From: Mark Brown <broonie(a)kernel.org>
[ Upstream commit 97eea946b93961fffd29448dcda7398d0d51c4b2 ]
The bounds checks in snd_soc_put_volsw_sx() are only being applied to the
first channel, meaning it is possible to write out of bounds values to the
second channel in stereo controls. Add appropriate checks.
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Link: https://lore.kernel.org/r/20220511134137.169575-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Signed-off-by: Sasha Levin <sashal(a)kernel.org>
---
sound/soc/soc-ops.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/sound/soc/soc-ops.c b/sound/soc/soc-ops.c
index 81c9ecfa7c7f9..63c0e61b17541 100644
--- a/sound/soc/soc-ops.c
+++ b/sound/soc/soc-ops.c
@@ -465,6 +465,12 @@ int snd_soc_put_volsw_sx(struct snd_kcontrol *kcontrol,
if (snd_soc_volsw_is_stereo(mc)) {
val_mask = mask << rshift;
val2 = (ucontrol->value.integer.value[1] + min) & mask;
+
+ if (mc->platform_max && val2 > mc->platform_max)
+ return -EINVAL;
+ if (val2 > max)
+ return -EINVAL;
+
val2 = val2 << rshift;
err = snd_soc_component_update_bits(component, reg2, val_mask,
--
2.39.2
From: Mark Brown <broonie(a)kernel.org>
[ Upstream commit 97eea946b93961fffd29448dcda7398d0d51c4b2 ]
The bounds checks in snd_soc_put_volsw_sx() are only being applied to the
first channel, meaning it is possible to write out of bounds values to the
second channel in stereo controls. Add appropriate checks.
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Link: https://lore.kernel.org/r/20220511134137.169575-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Signed-off-by: Sasha Levin <sashal(a)kernel.org>
---
sound/soc/soc-ops.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/sound/soc/soc-ops.c b/sound/soc/soc-ops.c
index 453b61b42dd9e..00e6a6e46fe52 100644
--- a/sound/soc/soc-ops.c
+++ b/sound/soc/soc-ops.c
@@ -460,6 +460,12 @@ int snd_soc_put_volsw_sx(struct snd_kcontrol *kcontrol,
if (snd_soc_volsw_is_stereo(mc)) {
val_mask = mask << rshift;
val2 = (ucontrol->value.integer.value[1] + min) & mask;
+
+ if (mc->platform_max && val2 > mc->platform_max)
+ return -EINVAL;
+ if (val2 > max)
+ return -EINVAL;
+
val2 = val2 << rshift;
err = snd_soc_component_update_bits(component, reg2, val_mask,
--
2.39.2
From: Mark Brown <broonie(a)kernel.org>
[ Upstream commit 97eea946b93961fffd29448dcda7398d0d51c4b2 ]
The bounds checks in snd_soc_put_volsw_sx() are only being applied to the
first channel, meaning it is possible to write out of bounds values to the
second channel in stereo controls. Add appropriate checks.
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Link: https://lore.kernel.org/r/20220511134137.169575-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie(a)kernel.org>
Signed-off-by: Sasha Levin <sashal(a)kernel.org>
---
sound/soc/soc-ops.c | 6 ++++++
1 file changed, 6 insertions(+)
diff --git a/sound/soc/soc-ops.c b/sound/soc/soc-ops.c
index 453b61b42dd9e..00e6a6e46fe52 100644
--- a/sound/soc/soc-ops.c
+++ b/sound/soc/soc-ops.c
@@ -460,6 +460,12 @@ int snd_soc_put_volsw_sx(struct snd_kcontrol *kcontrol,
if (snd_soc_volsw_is_stereo(mc)) {
val_mask = mask << rshift;
val2 = (ucontrol->value.integer.value[1] + min) & mask;
+
+ if (mc->platform_max && val2 > mc->platform_max)
+ return -EINVAL;
+ if (val2 > max)
+ return -EINVAL;
+
val2 = val2 << rshift;
err = snd_soc_component_update_bits(component, reg2, val_mask,
--
2.39.2
From: Lorenz Brun <lorenz(a)brun.one>
[ Upstream commit 03633c4ef1fb5ee119296dfe0c411656a9b5e04f ]
Currently the ROCK64 device tree specifies two regulators, vcc_host_5v
and vcc_host1_5v for USB VBUS on the device. Both of those are however
specified with RK_PA2 as the GPIO enabling them, causing the following
error when booting:
rockchip-pinctrl pinctrl: pin gpio0-2 already requested by vcc-host-5v-regulator; cannot claim for vcc-host1-5v-regulator
rockchip-pinctrl pinctrl: pin-2 (vcc-host1-5v-regulator) status -22
rockchip-pinctrl pinctrl: could not request pin 2 (gpio0-2) from group usb20-host-drv on device rockchip-pinctrl
reg-fixed-voltage vcc-host1-5v-regulator: Error applying setting, reverse things back
Looking at the schematic, there are in fact three USB regulators,
vcc_host_5v, vcc_host1_5v and vcc_otg_v5. But the enable signal for all
three is driven by Q2604 which is in turn driven by GPIO_A2/PA2.
Since these three regulators are not controllable separately, I removed
the second one which was causing the error and added labels for all
rails to the single regulator.
Signed-off-by: Lorenz Brun <lorenz(a)brun.one>
Tested-by: Diederik de Haas <didi.debian(a)cknow.org>
Link: https://lore.kernel.org/r/20230421213841.3079632-1-lorenz@brun.one
Signed-off-by: Heiko Stuebner <heiko(a)sntech.de>
Signed-off-by: Sasha Levin <sashal(a)kernel.org>
---
arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 14 ++------------
1 file changed, 2 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index 95ab6928cfd40..d6a288b0e2ab6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -32,7 +32,8 @@ vcc_sd: sdmmc-regulator {
vin-supply = <&vcc_io>;
};
- vcc_host_5v: vcc-host-5v-regulator {
+ /* Common enable line for all of the rails mentioned in the labels */
+ vcc_host_5v: vcc_host1_5v: vcc_otg_5v: vcc-host-5v-regulator {
compatible = "regulator-fixed";
gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
@@ -43,17 +44,6 @@ vcc_host_5v: vcc-host-5v-regulator {
vin-supply = <&vcc_sys>;
};
- vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
- compatible = "regulator-fixed";
- gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb20_host_drv>;
- regulator-name = "vcc_host1_5v";
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vcc_sys>;
- };
-
vcc_sys: vcc-sys {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
--
2.39.2
From: Lorenz Brun <lorenz(a)brun.one>
[ Upstream commit 03633c4ef1fb5ee119296dfe0c411656a9b5e04f ]
Currently the ROCK64 device tree specifies two regulators, vcc_host_5v
and vcc_host1_5v for USB VBUS on the device. Both of those are however
specified with RK_PA2 as the GPIO enabling them, causing the following
error when booting:
rockchip-pinctrl pinctrl: pin gpio0-2 already requested by vcc-host-5v-regulator; cannot claim for vcc-host1-5v-regulator
rockchip-pinctrl pinctrl: pin-2 (vcc-host1-5v-regulator) status -22
rockchip-pinctrl pinctrl: could not request pin 2 (gpio0-2) from group usb20-host-drv on device rockchip-pinctrl
reg-fixed-voltage vcc-host1-5v-regulator: Error applying setting, reverse things back
Looking at the schematic, there are in fact three USB regulators,
vcc_host_5v, vcc_host1_5v and vcc_otg_v5. But the enable signal for all
three is driven by Q2604 which is in turn driven by GPIO_A2/PA2.
Since these three regulators are not controllable separately, I removed
the second one which was causing the error and added labels for all
rails to the single regulator.
Signed-off-by: Lorenz Brun <lorenz(a)brun.one>
Tested-by: Diederik de Haas <didi.debian(a)cknow.org>
Link: https://lore.kernel.org/r/20230421213841.3079632-1-lorenz@brun.one
Signed-off-by: Heiko Stuebner <heiko(a)sntech.de>
Signed-off-by: Sasha Levin <sashal(a)kernel.org>
---
arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 14 ++------------
1 file changed, 2 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index 1b0f7e4551ea4..522d2d4281033 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -37,7 +37,8 @@ vcc_sd: sdmmc-regulator {
vin-supply = <&vcc_io>;
};
- vcc_host_5v: vcc-host-5v-regulator {
+ /* Common enable line for all of the rails mentioned in the labels */
+ vcc_host_5v: vcc_host1_5v: vcc_otg_5v: vcc-host-5v-regulator {
compatible = "regulator-fixed";
gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
@@ -48,17 +49,6 @@ vcc_host_5v: vcc-host-5v-regulator {
vin-supply = <&vcc_sys>;
};
- vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
- compatible = "regulator-fixed";
- gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb20_host_drv>;
- regulator-name = "vcc_host1_5v";
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vcc_sys>;
- };
-
vcc_sys: vcc-sys {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
--
2.39.2
From: Lorenz Brun <lorenz(a)brun.one>
[ Upstream commit 03633c4ef1fb5ee119296dfe0c411656a9b5e04f ]
Currently the ROCK64 device tree specifies two regulators, vcc_host_5v
and vcc_host1_5v for USB VBUS on the device. Both of those are however
specified with RK_PA2 as the GPIO enabling them, causing the following
error when booting:
rockchip-pinctrl pinctrl: pin gpio0-2 already requested by vcc-host-5v-regulator; cannot claim for vcc-host1-5v-regulator
rockchip-pinctrl pinctrl: pin-2 (vcc-host1-5v-regulator) status -22
rockchip-pinctrl pinctrl: could not request pin 2 (gpio0-2) from group usb20-host-drv on device rockchip-pinctrl
reg-fixed-voltage vcc-host1-5v-regulator: Error applying setting, reverse things back
Looking at the schematic, there are in fact three USB regulators,
vcc_host_5v, vcc_host1_5v and vcc_otg_v5. But the enable signal for all
three is driven by Q2604 which is in turn driven by GPIO_A2/PA2.
Since these three regulators are not controllable separately, I removed
the second one which was causing the error and added labels for all
rails to the single regulator.
Signed-off-by: Lorenz Brun <lorenz(a)brun.one>
Tested-by: Diederik de Haas <didi.debian(a)cknow.org>
Link: https://lore.kernel.org/r/20230421213841.3079632-1-lorenz@brun.one
Signed-off-by: Heiko Stuebner <heiko(a)sntech.de>
Signed-off-by: Sasha Levin <sashal(a)kernel.org>
---
arch/arm64/boot/dts/rockchip/rk3328-rock64.dts | 14 ++------------
1 file changed, 2 insertions(+), 12 deletions(-)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
index f69a38f42d2d5..0a27fa5271f57 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts
@@ -37,7 +37,8 @@ vcc_sd: sdmmc-regulator {
vin-supply = <&vcc_io>;
};
- vcc_host_5v: vcc-host-5v-regulator {
+ /* Common enable line for all of the rails mentioned in the labels */
+ vcc_host_5v: vcc_host1_5v: vcc_otg_5v: vcc-host-5v-regulator {
compatible = "regulator-fixed";
gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
@@ -48,17 +49,6 @@ vcc_host_5v: vcc-host-5v-regulator {
vin-supply = <&vcc_sys>;
};
- vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
- compatible = "regulator-fixed";
- gpio = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&usb20_host_drv>;
- regulator-name = "vcc_host1_5v";
- regulator-always-on;
- regulator-boot-on;
- vin-supply = <&vcc_sys>;
- };
-
vcc_sys: vcc-sys {
compatible = "regulator-fixed";
regulator-name = "vcc_sys";
--
2.39.2