In current implementation the Arasan NAND driver is updating the
system clock(i.e., anand->clk) in accordance to the timing modes
(i.e., SDR or NVDDR). But as per the Arasan NAND controller spec the
flash clock or the NAND bus clock(i.e., nfc->bus_clk), need to be
updated instead. This patch keeps the system clock unchanged and updates
the NAND bus clock as per the timing modes.
Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable(a)vger.kernel.org # 5.8+
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra(a)xilinx.com>
---
drivers/mtd/nand/raw/arasan-nand-controller.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
index 53bd10738418..c5264fa223c4 100644
--- a/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -347,17 +347,17 @@ static int anfc_select_target(struct nand_chip *chip, int target)
/* Update clock frequency */
if (nfc->cur_clk != anand->clk) {
- clk_disable_unprepare(nfc->controller_clk);
- ret = clk_set_rate(nfc->controller_clk, anand->clk);
+ clk_disable_unprepare(nfc->bus_clk);
+ ret = clk_set_rate(nfc->bus_clk, anand->clk);
if (ret) {
dev_err(nfc->dev, "Failed to change clock rate\n");
return ret;
}
- ret = clk_prepare_enable(nfc->controller_clk);
+ ret = clk_prepare_enable(nfc->bus_clk);
if (ret) {
dev_err(nfc->dev,
- "Failed to re-enable the controller clock\n");
+ "Failed to re-enable the bus clock\n");
return ret;
}
--
2.17.1
From: Olga Kitaina <okitain(a)gmail.com>
According to the Arasan NAND controller spec, the flash clock rate for SDR
must be <= 100 MHz, while for NV-DDR it must be the same as the rate of the
CLK line for the mode. The driver previously always set 100 MHz for NV-DDR,
which would result in incorrect behavior for NV-DDR modes 0-4.
The appropriate clock rate can be calculated from the NV-DDR timing
parameters as 1/tCK, or for rates measured in picoseconds,
10^12 / nand_nvddr_timings->tCK_min.
Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")
CC: stable(a)vger.kernel.org # 5.8+
Signed-off-by: Olga Kitaina <okitain(a)gmail.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra(a)xilinx.com>
---
drivers/mtd/nand/raw/arasan-nand-controller.c | 8 +++++++-
1 file changed, 7 insertions(+), 1 deletion(-)
diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
index c5264fa223c4..d4121d1243bf 100644
--- a/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -1043,7 +1043,13 @@ static int anfc_setup_interface(struct nand_chip *chip, int target,
DQS_BUFF_SEL_OUT(dqs_mode);
}
- anand->clk = ANFC_XLNX_SDR_DFLT_CORE_CLK;
+ if (nand_interface_is_sdr(conf)) {
+ anand->clk = ANFC_XLNX_SDR_DFLT_CORE_CLK;
+ } else {
+ /* ONFI timings are defined in picoseconds */
+ anand->clk = div_u64((u64)NSEC_PER_SEC * 1000,
+ conf->timings.nvddr.tCK_min);
+ }
/*
* Due to a hardware bug in the ZynqMP SoC, SDR timing modes 0-1 work
--
2.17.1