December 2022 - Linux-kselftest-mirror

[PATCH v2 net-next] selftests: forwarding: add Per-Stream Filtering and Policing test for Ocelot

by Vladimir Oltean

The Felix VSC9959 switch in NXP LS1028A supports the tc-gate action which enforced time-based access control per stream. A stream as seen by this switch is identified by {MAC DA, VID}. We use the standard forwarding selftest topology with 2 host interfaces and 2 switch interfaces. The host ports must require timestamping non-IP packets and supporting tc-etf offload, for isochron to work. The isochron program monitors network sync status (ptp4l, phc2sys) and deterministically transmits packets to the switch such that the tc-gate action either (a) always accepts them based on its schedule, or (b) always drops them. I tried to keep as much of the logic that isn't specific to the NXP LS1028A in a new tsn_lib.sh, for future reuse. This covers synchronization using ptp4l and phc2sys, and isochron. The cycle-time chosen for this selftest isn't particularly impressive (and the focus is the functionality of the switch), but I didn't really know what to do better, considering that it will mostly be run during debugging sessions, various kernel bloatware would be enabled, like lockdep, KASAN, etc, and we certainly can't run any races with those on. I tried to look through the kselftest framework for other real time applications and didn't really find any, so I'm not sure how better to prepare the environment in case we want to go for a lower cycle time. At the moment, the only thing the selftest is ensuring is that dynamic frequency scaling is disabled on the CPU that isochron runs on. It would probably be useful to have a blacklist of kernel config options (checked through zcat /proc/config.gz) and some cyclictest scripts to run beforehand, but I saw none of those. Signed-off-by: Vladimir Oltean <vladimir.oltean(a)nxp.com> --- v1->v2: - fix an off-by-one bug introduced at the last minute regarding which tc-mqprio queue was used for tc-etf and SO_TXTIME - introduce debugging for packets incorrectly received / incorrectly dropped based on "isochron report" - make the tsn_lib.sh dependency on isochron and linuxptp optional via REQUIRE_ISOCHRON and REQUIRE_LINUXPTP - avoid errors when CONFIG_CPU_FREQ is disabled - consistently use SCHED_FIFO instead of SCHED_RR for the isochron receiver .../selftests/drivers/net/ocelot/psfp.sh | 327 ++++++++++++++++++ .../selftests/net/forwarding/tsn_lib.sh | 235 +++++++++++++ 2 files changed, 562 insertions(+) create mode 100755 tools/testing/selftests/drivers/net/ocelot/psfp.sh create mode 100644 tools/testing/selftests/net/forwarding/tsn_lib.sh diff --git a/tools/testing/selftests/drivers/net/ocelot/psfp.sh b/tools/testing/selftests/drivers/net/ocelot/psfp.sh new file mode 100755 index 000000000000..5a5cee92c665 --- /dev/null +++ b/tools/testing/selftests/drivers/net/ocelot/psfp.sh @@ -0,0 +1,327 @@ +#!/bin/bash +# SPDX-License-Identifier: GPL-2.0 +# Copyright 2021-2022 NXP + +# Note: On LS1028A, in lack of enough user ports, this setup requires patching +# the device tree to use the second CPU port as a user port + +WAIT_TIME=1 +NUM_NETIFS=4 +STABLE_MAC_ADDRS=yes +NETIF_CREATE=no +lib_dir=$(dirname $0)/../../../net/forwarding +source $lib_dir/tc_common.sh +source $lib_dir/lib.sh +source $lib_dir/tsn_lib.sh + +UDS_ADDRESS_H1="/var/run/ptp4l_h1" +UDS_ADDRESS_SWP1="/var/run/ptp4l_swp1" + +# Tunables +NUM_PKTS=1000 +STREAM_VID=100 +STREAM_PRIO=6 +# Use a conservative cycle of 10 ms to allow the test to still pass when the +# kernel has some extra overhead like lockdep etc +CYCLE_TIME_NS=10000000 +# Create two Gate Control List entries, one OPEN and one CLOSE, of equal +# durations +GATE_DURATION_NS=$((${CYCLE_TIME_NS} / 2)) +# Give 2/3 of the cycle time to user space and 1/3 to the kernel +FUDGE_FACTOR=$((${CYCLE_TIME_NS} / 3)) +# Shift the isochron base time by half the gate time, so that packets are +# always received by swp1 close to the middle of the time slot, to minimize +# inaccuracies due to network sync +SHIFT_TIME_NS=$((${GATE_DURATION_NS} / 2)) + +h1=${NETIFS[p1]} +swp1=${NETIFS[p2]} +swp2=${NETIFS[p3]} +h2=${NETIFS[p4]} + +H1_IPV4="192.0.2.1" +H2_IPV4="192.0.2.2" +H1_IPV6="2001:db8:1::1" +H2_IPV6="2001:db8:1::2" + +# Chain number exported by the ocelot driver for +# Per-Stream Filtering and Policing filters +PSFP() +{ + echo 30000 +} + +psfp_chain_create() +{ + local if_name=$1 + + tc qdisc add dev $if_name clsact + + tc filter add dev $if_name ingress chain 0 pref 49152 flower \ + skip_sw action goto chain $(PSFP) +} + +psfp_chain_destroy() +{ + local if_name=$1 + + tc qdisc del dev $if_name clsact +} + +psfp_filter_check() +{ + local expected=$1 + local packets="" + local drops="" + local stats="" + + stats=$(tc -j -s filter show dev ${swp1} ingress chain $(PSFP) pref 1) + packets=$(echo ${stats} | jq ".[1].options.actions[].stats.packets") + drops=$(echo ${stats} | jq ".[1].options.actions[].stats.drops") + + if ! [ "${packets}" = "${expected}" ]; then + printf "Expected filter to match on %d packets but matched on %d instead\n" \ + "${expected}" "${packets}" + fi + + echo "Hardware filter reports ${drops} drops" +} + +h1_create() +{ + simple_if_init $h1 $H1_IPV4/24 $H1_IPV6/64 +} + +h1_destroy() +{ + simple_if_fini $h1 $H1_IPV4/24 $H1_IPV6/64 +} + +h2_create() +{ + simple_if_init $h2 $H2_IPV4/24 $H2_IPV6/64 +} + +h2_destroy() +{ + simple_if_fini $h2 $H2_IPV4/24 $H2_IPV6/64 +} + +switch_create() +{ + local h2_mac_addr=$(mac_get $h2) + + ip link set ${swp1} up + ip link set ${swp2} up + + ip link add br0 type bridge vlan_filtering 1 + ip link set ${swp1} master br0 + ip link set ${swp2} master br0 + ip link set br0 up + + bridge vlan add dev ${swp2} vid ${STREAM_VID} + bridge vlan add dev ${swp1} vid ${STREAM_VID} + # PSFP on Ocelot requires the filter to also be added to the bridge + # FDB, and not be removed + bridge fdb add dev ${swp2} \ + ${h2_mac_addr} vlan ${STREAM_VID} static master + + psfp_chain_create ${swp1} + + tc filter add dev ${swp1} ingress chain $(PSFP) pref 1 \ + protocol 802.1Q flower skip_sw \ + dst_mac ${h2_mac_addr} vlan_id ${STREAM_VID} \ + action gate base-time 0.000000000 \ + sched-entry OPEN ${GATE_DURATION_NS} -1 -1 \ + sched-entry CLOSE ${GATE_DURATION_NS} -1 -1 +} + +switch_destroy() +{ + psfp_chain_destroy ${swp1} + ip link del br0 +} + +txtime_setup() +{ + local if_name=$1 + + tc qdisc add dev ${if_name} clsact + # Classify PTP on TC 7 and isochron on TC 6 + tc filter add dev ${if_name} egress protocol 0x88f7 \ + flower action skbedit priority 7 + tc filter add dev ${if_name} egress protocol 802.1Q \ + flower vlan_ethtype 0xdead action skbedit priority 6 + tc qdisc add dev ${if_name} handle 100: parent root mqprio num_tc 8 \ + queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \ + map 0 1 2 3 4 5 6 7 \ + hw 1 + # Set up TC 6 for SO_TXTIME. tc-mqprio queues count from 1. + tc qdisc replace dev ${if_name} parent 100:$((${STREAM_PRIO} + 1)) etf \ + clockid CLOCK_TAI offload delta ${FUDGE_FACTOR} +} + +txtime_cleanup() +{ + local if_name=$1 + + tc qdisc del dev ${if_name} root + tc qdisc del dev ${if_name} clsact +} + +setup_prepare() +{ + vrf_prepare + + h1_create + h2_create + switch_create + + txtime_setup ${h1} + + # Set up swp1 as a master PHC for h1, synchronized to the local + # CLOCK_REALTIME. + phc2sys_start ${swp1} ${UDS_ADDRESS_SWP1} + + # Assumption true for LS1028A: h1 and h2 use the same PHC. So by + # synchronizing h1 to swp1 via PTP, h2 is also implicitly synchronized + # to swp1 (and both to CLOCK_REALTIME). + ptp4l_start ${h1} true ${UDS_ADDRESS_H1} + ptp4l_start ${swp1} false ${UDS_ADDRESS_SWP1} + + # Make sure there are no filter matches at the beginning of the test + psfp_filter_check 0 +} + +cleanup() +{ + pre_cleanup + + ptp4l_stop ${swp1} + ptp4l_stop ${h1} + phc2sys_stop + isochron_recv_stop + + txtime_cleanup ${h1} + + h2_destroy + h1_destroy + switch_destroy + + vrf_cleanup +} + +debug_incorrectly_dropped_packets() +{ + local isochron_dat=$1 + local dropped_seqids + local seqid + + echo "Packets incorrectly dropped:" + + dropped_seqids=$(isochron report \ + --input-file "${isochron_dat}" \ + --printf-format "%u RX hw %T\n" \ + --printf-args "qR" | \ + grep 'RX hw 0.000000000' | \ + awk '{print $1}') + + for seqid in ${dropped_seqids}; do + isochron report \ + --input-file "${isochron_dat}" \ + --start ${seqid} --stop ${seqid} \ + --printf-format "seqid %u scheduled for %T, HW TX timestamp %T\n" \ + --printf-args "qST" + done +} + +debug_incorrectly_received_packets() +{ + local isochron_dat=$1 + + echo "Packets incorrectly received:" + + isochron report \ + --input-file "${isochron_dat}" \ + --printf-format "seqid %u scheduled for %T, HW TX timestamp %T, HW RX timestamp %T\n" \ + --printf-args "qSTR" | + grep -v 'HW RX timestamp 0.000000000' +} + +run_test() +{ + local base_time=$1 + local expected=$2 + local test_name=$3 + local debug=$4 + local isochron_dat="$(mktemp)" + local extra_args="" + local received + + isochron_do \ + "${h1}" \ + "${h2}" \ + "${UDS_ADDRESS_H1}" \ + "" \ + "${base_time}" \ + "${CYCLE_TIME_NS}" \ + "${SHIFT_TIME_NS}" \ + "${NUM_PKTS}" \ + "${STREAM_VID}" \ + "${STREAM_PRIO}" \ + "" \ + "${isochron_dat}" + + # Count all received packets by looking at the non-zero RX timestamps + received=$(isochron report \ + --input-file "${isochron_dat}" \ + --printf-format "%u\n" --printf-args "R" | \ + grep -w -v '0' | wc -l) + + if [ "${received}" = "${expected}" ]; then + RET=0 + else + RET=1 + echo "Expected isochron to receive ${expected} packets but received ${received}" + fi + + log_test "${test_name}" + + if [ "$RET" = "1" ]; then + ${debug} "${isochron_dat}" + fi + + rm ${isochron_dat} 2> /dev/null +} + +test_gate_in_band() +{ + # Send packets in-band with the OPEN gate entry + run_test 0.000000000 ${NUM_PKTS} "In band" \ + debug_incorrectly_dropped_packets + + psfp_filter_check ${NUM_PKTS} +} + +test_gate_out_of_band() +{ + # Send packets in-band with the CLOSE gate entry + run_test 0.005000000 0 "Out of band" \ + debug_incorrectly_received_packets + + psfp_filter_check $((2 * ${NUM_PKTS})) +} + +trap cleanup EXIT + +ALL_TESTS=" + test_gate_in_band + test_gate_out_of_band +" + +setup_prepare +setup_wait + +tests_run + +exit $EXIT_STATUS diff --git a/tools/testing/selftests/net/forwarding/tsn_lib.sh b/tools/testing/selftests/net/forwarding/tsn_lib.sh new file mode 100644 index 000000000000..60a1423e8116 --- /dev/null +++ b/tools/testing/selftests/net/forwarding/tsn_lib.sh @@ -0,0 +1,235 @@ +#!/bin/bash +# SPDX-License-Identifier: GPL-2.0 +# Copyright 2021-2022 NXP + +REQUIRE_ISOCHRON=${REQUIRE_ISOCHRON:=yes} +REQUIRE_LINUXPTP=${REQUIRE_LINUXPTP:=yes} + +# Tunables +UTC_TAI_OFFSET=37 +ISOCHRON_CPU=1 + +if [[ "$REQUIRE_ISOCHRON" = "yes" ]]; then + # https://github.com/vladimiroltean/tsn-scripts + # WARNING: isochron versions pre-1.0 are unstable, + # always use the latest version + require_command isochron +fi +if [[ "$REQUIRE_LINUXPTP" = "yes" ]]; then + require_command phc2sys + require_command ptp4l +fi + +phc2sys_start() +{ + local if_name=$1 + local uds_address=$2 + local extra_args="" + + if ! [ -z "${uds_address}" ]; then + extra_args="${extra_args} -z ${uds_address}" + fi + + phc2sys_log="$(mktemp)" + + chrt -f 10 phc2sys -m \ + -c ${if_name} \ + -s CLOCK_REALTIME \ + -O ${UTC_TAI_OFFSET} \ + --step_threshold 0.00002 \ + --first_step_threshold 0.00002 \ + ${extra_args} \ + > "${phc2sys_log}" 2>&1 & + phc2sys_pid=$! + + echo "phc2sys logs to ${phc2sys_log} and has pid ${phc2sys_pid}" + + sleep 1 +} + +phc2sys_stop() +{ + { kill ${phc2sys_pid} && wait ${phc2sys_pid}; } 2> /dev/null + rm "${phc2sys_log}" 2> /dev/null +} + +ptp4l_start() +{ + local if_name=$1 + local slave_only=$2 + local uds_address=$3 + local log="ptp4l_log_${if_name}" + local pid="ptp4l_pid_${if_name}" + local extra_args="" + + if [ "${slave_only}" = true ]; then + extra_args="${extra_args} -s" + fi + + # declare dynamic variables ptp4l_log_${if_name} and ptp4l_pid_${if_name} + # as global, so that they can be referenced later + declare -g "${log}=$(mktemp)" + + chrt -f 10 ptp4l -m -2 -P \ + -i ${if_name} \ + --step_threshold 0.00002 \ + --first_step_threshold 0.00002 \ + --tx_timestamp_timeout 100 \ + --uds_address="${uds_address}" \ + ${extra_args} \ + > "${!log}" 2>&1 & + declare -g "${pid}=$!" + + echo "ptp4l for interface ${if_name} logs to ${!log} and has pid ${!pid}" + + sleep 1 +} + +ptp4l_stop() +{ + local if_name=$1 + local log="ptp4l_log_${if_name}" + local pid="ptp4l_pid_${if_name}" + + { kill ${!pid} && wait ${!pid}; } 2> /dev/null + rm "${!log}" 2> /dev/null +} + +cpufreq_max() +{ + local cpu=$1 + local freq="cpu${cpu}_freq" + local governor="cpu${cpu}_governor" + + # Kernel may be compiled with CONFIG_CPU_FREQ disabled + if ! [ -d /sys/bus/cpu/devices/cpu${cpu}/cpufreq ]; then + return + fi + + # declare dynamic variables cpu${cpu}_freq and cpu${cpu}_governor as + # global, so they can be referenced later + declare -g "${freq}=$(cat /sys/bus/cpu/devices/cpu${cpu}/cpufreq/scaling_min_freq)" + declare -g "${governor}=$(cat /sys/bus/cpu/devices/cpu${cpu}/cpufreq/scaling_governor)" + + cat /sys/bus/cpu/devices/cpu${cpu}/cpufreq/scaling_max_freq > \ + /sys/bus/cpu/devices/cpu${cpu}/cpufreq/scaling_min_freq + echo -n "performance" > \ + /sys/bus/cpu/devices/cpu${cpu}/cpufreq/scaling_governor +} + +cpufreq_restore() +{ + local cpu=$1 + local freq="cpu${cpu}_freq" + local governor="cpu${cpu}_governor" + + if ! [ -d /sys/bus/cpu/devices/cpu${cpu}/cpufreq ]; then + return + fi + + echo "${!freq}" > /sys/bus/cpu/devices/cpu${cpu}/cpufreq/scaling_min_freq + echo -n "${!governor}" > \ + /sys/bus/cpu/devices/cpu${cpu}/cpufreq/scaling_governor +} + +isochron_recv_start() +{ + local if_name=$1 + local uds=$2 + local extra_args=$3 + + if ! [ -z "${uds}" ]; then + extra_args="--unix-domain-socket ${uds}" + fi + + isochron rcv \ + --interface ${if_name} \ + --sched-priority 98 \ + --sched-fifo \ + --utc-tai-offset ${UTC_TAI_OFFSET} \ + --quiet \ + ${extra_args} & \ + isochron_pid=$! + + sleep 1 +} + +isochron_recv_stop() +{ + { kill ${isochron_pid} && wait ${isochron_pid}; } 2> /dev/null +} + +isochron_do() +{ + local sender_if_name=$1; shift + local receiver_if_name=$1; shift + local sender_uds=$1; shift + local receiver_uds=$1; shift + local base_time=$1; shift + local cycle_time=$1; shift + local shift_time=$1; shift + local num_pkts=$1; shift + local vid=$1; shift + local priority=$1; shift + local dst_ip=$1; shift + local isochron_dat=$1; shift + local extra_args="" + local receiver_extra_args="" + local vrf="$(master_name_get ${sender_if_name})" + local use_l2="true" + + if ! [ -z "${dst_ip}" ]; then + use_l2="false" + fi + + if ! [ -z "${vrf}" ]; then + dst_ip="${dst_ip}%${vrf}" + fi + + if ! [ -z "${vid}" ]; then + vid="--vid=${vid}" + fi + + if [ -z "${receiver_uds}" ]; then + extra_args="${extra_args} --omit-remote-sync" + fi + + if ! [ -z "${shift_time}" ]; then + extra_args="${extra_args} --shift-time=${shift_time}" + fi + + if [ "${use_l2}" = "true" ]; then + extra_args="${extra_args} --l2 --etype=0xdead ${vid}" + receiver_extra_args="--l2 --etype=0xdead" + else + extra_args="${extra_args} --l4 --ip-destination=${dst_ip}" + receiver_extra_args="--l4" + fi + + cpufreq_max ${ISOCHRON_CPU} + + isochron_recv_start "${h2}" "${receiver_uds}" "${receiver_extra_args}" + + isochron send \ + --interface ${sender_if_name} \ + --unix-domain-socket ${sender_uds} \ + --priority ${priority} \ + --base-time ${base_time} \ + --cycle-time ${cycle_time} \ + --num-frames ${num_pkts} \ + --frame-size 64 \ + --txtime \ + --utc-tai-offset ${UTC_TAI_OFFSET} \ + --cpu-mask $((1 << ${ISOCHRON_CPU})) \ + --sched-fifo \ + --sched-priority 98 \ + --client 127.0.0.1 \ + --sync-threshold 5000 \ + --output-file ${isochron_dat} \ + ${extra_args} \ + --quiet + + isochron_recv_stop + + cpufreq_restore ${ISOCHRON_CPU} +} -- 2.25.1

1 year, 10 months

5
13
0 0

[PATCH i-g-t v2 0/4] Add support for KUnit tests

by Isabella Basso

This patch series was first developed as part of the LKCamp hackathon that happened last year[1], mainly focusing on refactoring DRM tests to use KUnit. KUnit[2][3] is a unified test framework that provides helper tools, simplifying their development and execution. Using an x86-64 machine it's possible to run tests in the host's kernel natively using user-mode Linux[4] (aka UML), which simplifies usage in a wide variety of scenarios, including integration to CI. As the tool's adoption widens into graphics testing territory, I and LKCamp members figured it would be important to support it in IGT, as it's a core tool for GPU drivers maintainers. I have then added KUnit support into IGT mainly following the KTAP specs, and it can be tested using patch 4/4 in this series together with a DRM selftests patch series available at [5]. Changes since v1: - Major rework of parsing function structure: - It is not longer recursive - Adapt kselftests functions and structs to be used with KUnit - Switch DRM selftests to KUnit parsing as they're updated in the kernel - Replace AMD KUnit tests by DRM selftests [1]: https://groups.google.com/g/kunit-dev/c/YqFR1q2uZvk/m/IbvItSfHBAAJ [2]: https://kunit.dev [3]: https://docs.kernel.org/dev-tools/kunit/index.html [4]: http://user-mode-linux.sourceforge.net [5]: https://lore.kernel.org/all/20220708203052.236290-1-maira.canal@usp.br/ Isabella Basso (4): lib/igt_kmod: rename kselftest functions to ktest lib/igt_kmod.c: check if module is builtin before attempting to unload it lib/igt_kmod: add compatibility for KUnit tests: DRM selftests: switch to KUnit lib/igt_kmod.c | 315 +++++++++++++++++++++++++++++++++++++++++-- lib/igt_kmod.h | 14 +- tests/drm_buddy.c | 7 +- tests/drm_mm.c | 7 +- tests/kms_selftest.c | 12 +- 5 files changed, 329 insertions(+), 26 deletions(-) -- 2.37.2

1 year, 10 months

6
29
0 0

[PATCH] selftests: fix LLVM build for i386 and x86_64

by Guillaume Tucker

Add missing cases for the i386 and x86_64 architectures when determining the LLVM target for building kselftest. Fixes: 795285ef2425 ("selftests: Fix clang cross compilation") Signed-off-by: Guillaume Tucker <guillaume.tucker(a)collabora.com> --- tools/testing/selftests/lib.mk | 2 ++ 1 file changed, 2 insertions(+) diff --git a/tools/testing/selftests/lib.mk b/tools/testing/selftests/lib.mk index b1c62914366b..cc4c443d5b14 100644 --- a/tools/testing/selftests/lib.mk +++ b/tools/testing/selftests/lib.mk @@ -10,12 +10,14 @@ endif CLANG_TARGET_FLAGS_arm := arm-linux-gnueabi CLANG_TARGET_FLAGS_arm64 := aarch64-linux-gnu CLANG_TARGET_FLAGS_hexagon := hexagon-linux-musl +CLANG_TARGET_FLAGS_i386 := i386-linux-gnu CLANG_TARGET_FLAGS_m68k := m68k-linux-gnu CLANG_TARGET_FLAGS_mips := mipsel-linux-gnu CLANG_TARGET_FLAGS_powerpc := powerpc64le-linux-gnu CLANG_TARGET_FLAGS_riscv := riscv64-linux-gnu CLANG_TARGET_FLAGS_s390 := s390x-linux-gnu CLANG_TARGET_FLAGS_x86 := x86_64-linux-gnu +CLANG_TARGET_FLAGS_x86_64 := x86_64-linux-gnu CLANG_TARGET_FLAGS := $(CLANG_TARGET_FLAGS_$(ARCH)) ifeq ($(CROSS_COMPILE),) -- 2.30.2

1 year, 10 months

2
2
0 0

[PATCH] selftests: add missing ')' in lib.mk

by Guillaume Tucker

Add missing closing ')' in lib.mk in a call to $error(). This only affects LLVM / Clang builds. Fixes: 795285ef2425 ("selftests: Fix clang cross compilation") Signed-off-by: Guillaume Tucker <guillaume.tucker(a)collabora.com> --- tools/testing/selftests/lib.mk | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/testing/selftests/lib.mk b/tools/testing/selftests/lib.mk index 947fc72413e9..a87f60873e5b 100644 --- a/tools/testing/selftests/lib.mk +++ b/tools/testing/selftests/lib.mk @@ -20,7 +20,7 @@ CLANG_TARGET_FLAGS := $(CLANG_TARGET_FLAGS_$(ARCH)) ifeq ($(CROSS_COMPILE),) ifeq ($(CLANG_TARGET_FLAGS),) -$(error Specify CROSS_COMPILE or add '--target=' option to lib.mk +$(error Specify CROSS_COMPILE or add '--target=' option to lib.mk) else CLANG_FLAGS += --target=$(CLANG_TARGET_FLAGS) endif # CLANG_TARGET_FLAGS -- 2.30.2

1 year, 10 months

3
3
0 0

[PATCH net-next v2 0/3] net: introduce rps_default_mask

by Paolo Abeni

Real-time setups try hard to ensure proper isolation between time critical applications and e.g. network processing performed by the network stack in softirq and RPS is used to move the softirq activity away from the isolated core. If the network configuration is dynamic, with netns and devices routinely created at run-time, enforcing the correct RPS setting on each newly created device allowing to transient bad configuration became complex. These series try to address the above, introducing a new sysctl knob: rps_default_mask. The new sysctl entry allows configuring a systemwide RPS mask, to be enforced since receive queue creation time without any fourther per device configuration required. Additionally, a simple self-test is introduced to check the rps_default_mask behavior. v1 -> v2: - fix sparse warning in patch 2/3 Paolo Abeni (3): net/sysctl: factor-out netdev_rx_queue_set_rps_mask() helper net/core: introduce default_rps_mask netns attribute self-tests: introduce self-tests for RPS default mask Documentation/admin-guide/sysctl/net.rst | 6 ++ include/linux/netdevice.h | 1 + net/core/net-sysfs.c | 73 +++++++++++-------- net/core/sysctl_net_core.c | 58 +++++++++++++++ tools/testing/selftests/net/Makefile | 1 + tools/testing/selftests/net/config | 3 + .../testing/selftests/net/rps_default_mask.sh | 57 +++++++++++++++ 7 files changed, 169 insertions(+), 30 deletions(-) create mode 100755 tools/testing/selftests/net/rps_default_mask.sh -- 2.26.2

1 year, 10 months

4
12
0 0

[PATCH v6] tracing/probe: add a char type to show the character value of traced arguments

by Donglin Peng

There are scenes that we want to show the character value of traced arguments other than a decimal or hexadecimal or string value for debug convinience. I add a new type named 'char' to do it and a new test case file named 'kprobe_args_char.tc' to do selftest for char type. For example: The to be traced function is 'void demo_func(char type, char *name);', we can add a kprobe event as follows to show argument values as we want: echo 'p:myprobe demo_func $arg1:char +0($arg2):char[5]' > kprobe_events we will get the following trace log: ... myprobe: (demo_func+0x0/0x29) arg1='A' arg2={'b','p','f','1',''} Signed-off-by: Donglin Peng <dolinux.peng(a)gmail.com> Acked-by: Masami Hiramatsu (Google) <mhiramat(a)kernel.org> Reported-by: kernel test robot <lkp(a)intel.com> --- Changes in v6: - change "\'%c\'" to "'%c'" in trace_probe.c Changes in v5: - wrap the output character with single quotes - add a test case named kprobe_args_char.tc to do selftest Changes in v4: - update the example in the commit log Changes in v3: - update readme_msg Changes in v2: - fix build warnings reported by kernel test robot - modify commit log --- Documentation/trace/kprobetrace.rst | 3 +- kernel/trace/trace.c | 2 +- kernel/trace/trace_probe.c | 2 + kernel/trace/trace_probe.h | 1 + .../ftrace/test.d/kprobe/kprobe_args_char.tc | 47 +++++++++++++++++++ 5 files changed, 53 insertions(+), 2 deletions(-) create mode 100644 tools/testing/selftests/ftrace/test.d/kprobe/kprobe_args_char.tc diff --git a/Documentation/trace/kprobetrace.rst b/Documentation/trace/kprobetrace.rst index 4274cc6a2f94..007972a3c5c4 100644 --- a/Documentation/trace/kprobetrace.rst +++ b/Documentation/trace/kprobetrace.rst @@ -58,7 +58,7 @@ Synopsis of kprobe_events NAME=FETCHARG : Set NAME as the argument name of FETCHARG. FETCHARG:TYPE : Set TYPE as the type of FETCHARG. Currently, basic types (u8/u16/u32/u64/s8/s16/s32/s64), hexadecimal types - (x8/x16/x32/x64), "string", "ustring" and bitfield + (x8/x16/x32/x64), "char", "string", "ustring" and bitfield are supported. (\*1) only for the probe on function entry (offs == 0). @@ -80,6 +80,7 @@ E.g. 'x16[4]' means an array of x16 (2bytes hex) with 4 elements. Note that the array can be applied to memory type fetchargs, you can not apply it to registers/stack-entries etc. (for example, '$stack1:x8[8]' is wrong, but '+8($stack):x8[8]' is OK.) +Char type can be used to show the character value of traced arguments. String type is a special type, which fetches a "null-terminated" string from kernel space. This means it will fail and store NULL if the string container has been paged out. "ustring" type is an alternative of string for user-space. diff --git a/kernel/trace/trace.c b/kernel/trace/trace.c index 6d7ef130f57e..c602081e64c8 100644 --- a/kernel/trace/trace.c +++ b/kernel/trace/trace.c @@ -5615,7 +5615,7 @@ static const char readme_msg[] = "\t $stack<index>, $stack, $retval, $comm,\n" #endif "\t +|-[u]<offset>(<fetcharg>), \\imm-value, \\\"imm-string\"\n" - "\t type: s8/16/32/64, u8/16/32/64, x8/16/32/64, string, symbol,\n" + "\t type: s8/16/32/64, u8/16/32/64, x8/16/32/64, char, string, symbol,\n" "\t b<bit-width>@<bit-offset>/<container-size>, ustring,\n" "\t <type>\\[<array-size>\\]\n" #ifdef CONFIG_HIST_TRIGGERS diff --git a/kernel/trace/trace_probe.c b/kernel/trace/trace_probe.c index bb2f95d7175c..794a21455396 100644 --- a/kernel/trace/trace_probe.c +++ b/kernel/trace/trace_probe.c @@ -50,6 +50,7 @@ DEFINE_BASIC_PRINT_TYPE_FUNC(x8, u8, "0x%x") DEFINE_BASIC_PRINT_TYPE_FUNC(x16, u16, "0x%x") DEFINE_BASIC_PRINT_TYPE_FUNC(x32, u32, "0x%x") DEFINE_BASIC_PRINT_TYPE_FUNC(x64, u64, "0x%Lx") +DEFINE_BASIC_PRINT_TYPE_FUNC(char, u8, "'%c'") int PRINT_TYPE_FUNC_NAME(symbol)(struct trace_seq *s, void *data, void *ent) { @@ -93,6 +94,7 @@ static const struct fetch_type probe_fetch_types[] = { ASSIGN_FETCH_TYPE_ALIAS(x16, u16, u16, 0), ASSIGN_FETCH_TYPE_ALIAS(x32, u32, u32, 0), ASSIGN_FETCH_TYPE_ALIAS(x64, u64, u64, 0), + ASSIGN_FETCH_TYPE_ALIAS(char, u8, u8, 0), ASSIGN_FETCH_TYPE_ALIAS(symbol, ADDR_FETCH_TYPE, ADDR_FETCH_TYPE, 0), ASSIGN_FETCH_TYPE_END diff --git a/kernel/trace/trace_probe.h b/kernel/trace/trace_probe.h index de38f1c03776..8c86aaa8b0c9 100644 --- a/kernel/trace/trace_probe.h +++ b/kernel/trace/trace_probe.h @@ -164,6 +164,7 @@ DECLARE_BASIC_PRINT_TYPE_FUNC(x16); DECLARE_BASIC_PRINT_TYPE_FUNC(x32); DECLARE_BASIC_PRINT_TYPE_FUNC(x64); +DECLARE_BASIC_PRINT_TYPE_FUNC(char); DECLARE_BASIC_PRINT_TYPE_FUNC(string); DECLARE_BASIC_PRINT_TYPE_FUNC(symbol); diff --git a/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_args_char.tc b/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_args_char.tc new file mode 100644 index 000000000000..285b4770efad --- /dev/null +++ b/tools/testing/selftests/ftrace/test.d/kprobe/kprobe_args_char.tc @@ -0,0 +1,47 @@ +#!/bin/sh +# SPDX-License-Identifier: GPL-2.0 +# description: Kprobe event char type argument +# requires: kprobe_events + +case `uname -m` in +x86_64) + ARG1=%di +;; +i[3456]86) + ARG1=%ax +;; +aarch64) + ARG1=%x0 +;; +arm*) + ARG1=%r0 +;; +ppc64*) + ARG1=%r3 +;; +ppc*) + ARG1=%r3 +;; +s390*) + ARG1=%r2 +;; +mips*) + ARG1=%r4 +;; +*) + echo "Please implement other architecture here" + exit_untested +esac + +: "Test get argument (1)" +echo "p:testprobe tracefs_create_dir arg1=+0(${ARG1}):char" > kprobe_events +echo 1 > events/kprobes/testprobe/enable +echo "p:test $FUNCTION_FORK" >> kprobe_events +grep -qe "testprobe.* arg1='t'" trace + +echo 0 > events/kprobes/testprobe/enable +: "Test get argument (2)" +echo "p:testprobe tracefs_create_dir arg1=+0(${ARG1}):char arg2=+0(${ARG1}):char[4]" > kprobe_events +echo 1 > events/kprobes/testprobe/enable +echo "p:test $FUNCTION_FORK" >> kprobe_events +grep -qe "testprobe.* arg1='t' arg2={'t','e','s','t'}" trace -- 2.25.1

1 year, 11 months

3
2
0 0

[PATCH bpf-next v3 00/16] bpfilter

by Quentin Deslandes

The patchset is based on the patches from David S. Miller [1], Daniel Borkmann [2], and Dmitrii Banshchikov [3]. Note: I've partially sent this patchset earlier due to a mistake on my side, sorry for then noise. The main goal of the patchset is to prepare bpfilter for iptables' configuration blob parsing and code generation. The patchset introduces data structures and code for matches, targets, rules and tables. Beside that the code generation is introduced. The first version of the code generation supports only "inline" mode - all chains and their rules emit instructions in linear approach. Things that are not implemented yet: 1) The process of switching from the previous BPF programs to the new set isn't atomic. 2) No support of device ifindex - it's hardcoded 3) No helper subprog for counters update Another problem is using iptables' blobs for tests and filter table initialization. While it saves lines something more maintainable should be done here. The plan for the next iteration: 1) Add a helper program for counters update 2) Handle ifindex Patches 1/2 adds definitions of the used types. Patch 3 adds logging to bpfilter. Patch 4 adds an associative map. Patch 5 add runtime context structure. Patches 6/7 add code generation infrastructure and TC code generator. Patches 8/9/10/11/12 add code for matches, targets, rules and table. Patch 13 adds code generation for table. Patch 14 handles hooked setsockopt(2) calls. Patch 15 adds filter table Patch 16 uses prepared code in main(). Due to poor hardware availability on my side, I've not been able to benchmark those changes. I plan to get some numbers for the next iteration. FORWARD filter chain is now supported, however, it's attached to TC INGRESS along with INPUT filter chain. This is due to XDP not supporting multiple programs to be attached. I could generate a single program out of both INPUT and FORWARD chains, but that would prevent another BPF program to be attached to the interface anyway. If a solution exists to attach both those programs to XDP while allowing for other programs to be attached, it requires more investigation. In the meantime, INPUT and FORWARD filtering is supported using TC. Most of the code in this series was written by Dmitrii Banshchikov, my changes are limited to v3. I've tried to reflect this fact in the commits by adding 'Co-developed-by:' and 'Signed-off-by:' for Dmitrii, please tell me this was done the wrong way. v2 -> v3 Chains: * Add support for FORWARD filter chain. * Add generation of BPF bytecode to assess whether a packet should be forwarded or not, using bpf_fib_lookup(). * Allow for multiple programs to be attached to TC. * Allow for multiple TC hooks to be used. Code generation: * Remove duplicated BPF bytecode generation. * Fix a bug regarding jump offset during generation. * Remove support for XDP from the series, as it's not currently used. Table: * Add new filter_table_update_counters() virtual call. It updates the table's counter stored in the ipt_entry structure. This way, when iptables tries to fetch the values of the counters, bpfilter only has to copy the ipt_entry cached in the table structure. Logging: * Refactor logging primitives. Sockopts: * Add support for userspace counters querying. Rule: * Store the rule's index inside struct rule, to each counters' map usage. v1 -> v2 Maps: * Use map_upsert instead of separate map_insert and map_update Matches: * Add a new virtual call - gen_inline. The call is used for * inline generating of a rule's match. Targets: * Add a new virtual call - gen_inline. The call is used for inline generating of a rule's target. Rules: * Add code generation for rules Table: * Add struct table_ops * Add map for table_ops * Add filter table * Reorganize the way filter table is initialized Sockopts: * Install/uninstall BPF programs while handling IPT_SO_SET_REPLACE Code generation: * Add first version of the code generation Dependencies: * Add libbpf v0 -> v1 IO: * Use ssize_t in pvm_read, pvm_write for total_bytes * Move IO functions into sockopt.c and main.c Logging: * Use LOGLEVEL_EMERG, LOGLEVEL_NOTICE, LOGLEVE_DEBUG while logging to /dev/kmsg * Prepend log message with <n> where n is log level * Conditionally enable BFLOG_DEBUG messages * Merge bflog.{h,c} into context.h Matches: * Reorder fields in struct match_ops for tight packing * Get rid of struct match_ops_map * Rename udp_match_ops to xt_udp * Use XT_ALIGN macro * Store payload size in match size * Move udp match routines into a separate file Targets: * Reorder fields in struct target_ops for tight packing * Get rid of struct target_ops_map * Add comments for convert_verdict function Rules: * Add validation Tables: * Combine table_map and table_list into table_index * Add validation Sockopts: * Handle IPT_SO_GET_REVISION_TARGET 1. https://lore.kernel.org/patchwork/patch/902785/ 2. https://lore.kernel.org/patchwork/patch/902783/ 3. https://kernel.ubuntu.com/~cking/stress-ng/stress-ng.pdf Quentin Deslandes (16): bpfilter: add types for usermode helper tools: add bpfilter usermode helper header bpfilter: add logging facility bpfilter: add map container bpfilter: add runtime context bpfilter: add BPF bytecode generation infrastructure bpfilter: add support for TC bytecode generation bpfilter: add match structure bpfilter: add support for src/dst addr and ports bpfilter: add target structure bpfilter: add rule structure bpfilter: add table structure bpfilter: add table code generation bpfilter: add setsockopt() support bpfilter: add filter table bpfilter: handle setsockopt() calls include/uapi/linux/bpfilter.h | 154 +++ net/bpfilter/Makefile | 16 +- net/bpfilter/codegen.c | 1040 +++++++++++++++++ net/bpfilter/codegen.h | 183 +++ net/bpfilter/context.c | 168 +++ net/bpfilter/context.h | 24 + net/bpfilter/filter-table.c | 344 ++++++ net/bpfilter/filter-table.h | 18 + net/bpfilter/logger.c | 52 + net/bpfilter/logger.h | 80 ++ net/bpfilter/main.c | 132 ++- net/bpfilter/map-common.c | 51 + net/bpfilter/map-common.h | 19 + net/bpfilter/match.c | 55 + net/bpfilter/match.h | 37 + net/bpfilter/rule.c | 286 +++++ net/bpfilter/rule.h | 37 + net/bpfilter/sockopt.c | 533 +++++++++ net/bpfilter/sockopt.h | 15 + net/bpfilter/table.c | 391 +++++++ net/bpfilter/table.h | 59 + net/bpfilter/target.c | 203 ++++ net/bpfilter/target.h | 57 + net/bpfilter/xt_udp.c | 111 ++ tools/include/uapi/linux/bpfilter.h | 175 +++ .../testing/selftests/bpf/bpfilter/.gitignore | 8 + tools/testing/selftests/bpf/bpfilter/Makefile | 57 + .../selftests/bpf/bpfilter/bpfilter_util.h | 80 ++ .../selftests/bpf/bpfilter/test_codegen.c | 338 ++++++ .../testing/selftests/bpf/bpfilter/test_map.c | 63 + .../selftests/bpf/bpfilter/test_match.c | 69 ++ .../selftests/bpf/bpfilter/test_rule.c | 56 + .../selftests/bpf/bpfilter/test_target.c | 83 ++ .../selftests/bpf/bpfilter/test_xt_udp.c | 48 + 34 files changed, 4999 insertions(+), 43 deletions(-) create mode 100644 net/bpfilter/codegen.c create mode 100644 net/bpfilter/codegen.h create mode 100644 net/bpfilter/context.c create mode 100644 net/bpfilter/context.h create mode 100644 net/bpfilter/filter-table.c create mode 100644 net/bpfilter/filter-table.h create mode 100644 net/bpfilter/logger.c create mode 100644 net/bpfilter/logger.h create mode 100644 net/bpfilter/map-common.c create mode 100644 net/bpfilter/map-common.h create mode 100644 net/bpfilter/match.c create mode 100644 net/bpfilter/match.h create mode 100644 net/bpfilter/rule.c create mode 100644 net/bpfilter/rule.h create mode 100644 net/bpfilter/sockopt.c create mode 100644 net/bpfilter/sockopt.h create mode 100644 net/bpfilter/table.c create mode 100644 net/bpfilter/table.h create mode 100644 net/bpfilter/target.c create mode 100644 net/bpfilter/target.h create mode 100644 net/bpfilter/xt_udp.c create mode 100644 tools/include/uapi/linux/bpfilter.h create mode 100644 tools/testing/selftests/bpf/bpfilter/.gitignore create mode 100644 tools/testing/selftests/bpf/bpfilter/Makefile create mode 100644 tools/testing/selftests/bpf/bpfilter/bpfilter_util.h create mode 100644 tools/testing/selftests/bpf/bpfilter/test_codegen.c create mode 100644 tools/testing/selftests/bpf/bpfilter/test_map.c create mode 100644 tools/testing/selftests/bpf/bpfilter/test_match.c create mode 100644 tools/testing/selftests/bpf/bpfilter/test_rule.c create mode 100644 tools/testing/selftests/bpf/bpfilter/test_target.c create mode 100644 tools/testing/selftests/bpf/bpfilter/test_xt_udp.c -- 2.38.1

1 year, 11 months

3
24
0 0

[PATCH 1/2] kselftest/arm64: Remove the local NUM_VL definition

by Zenghui Yu

It was introduced in commit b77e995e3b96 ("kselftest/arm64: Add a test program to exercise the syscall ABI") but never actually used. Remove it. Signed-off-by: Zenghui Yu <yuzenghui(a)huawei.com> --- tools/testing/selftests/arm64/abi/syscall-abi.c | 2 -- 1 file changed, 2 deletions(-) diff --git a/tools/testing/selftests/arm64/abi/syscall-abi.c b/tools/testing/selftests/arm64/abi/syscall-abi.c index 9800f9dc6b35..24a498029c78 100644 --- a/tools/testing/selftests/arm64/abi/syscall-abi.c +++ b/tools/testing/selftests/arm64/abi/syscall-abi.c @@ -20,8 +20,6 @@ #include "syscall-abi.h" -#define NUM_VL ((SVE_VQ_MAX - SVE_VQ_MIN) + 1) - static int default_sme_vl; extern void do_syscall(int sve_vl, int sme_vl); -- 2.33.0

1 year, 11 months

3
4
0 0

[PATCH v3 0/4] arm64/signal: Support TPIDR2

by Mark Brown

When SME support was merged support for TPIDR2 in signal frames was omitted, meaning that it was not possible for signal handers to inspect or modify it. This will present an issue for programs using signals to implement lightweight threads so let's provide access to TPIDR2 in signal handlers. Implement a new record type for TPIDR2 using the same format as we use for ESR and add coverage to make sure that this appears in the signal context as expected. Due to TPIDR2 being reserved for libc we only validate that the value is unchanged, meaning we're likely to just be validating the default value of 0 on current systems. I have tested with a modified version that sets an explicit value. v3: - Rebase onto v6.2-rc1. v2: - Rebase onto v6.1-rc3. - Change the signal frame magic to 0x54504902 (TPI). To: Catalin Marinas <catalin.marinas(a)arm.com> To: Will Deacon <will(a)kernel.org> To: Shuah Khan <shuah(a)kernel.org> Cc: Szabolcs Nagy <szabolcs.nagy(a)arm.com> Cc: linux-arm-kernel(a)lists.infradead.org Cc: linux-kselftest(a)vger.kernel.org Signed-off-by: Mark Brown <broonie(a)kernel.org> --- Mark Brown (4): arm64/sme: Document ABI for TPIDR2 signal information arm64/signal: Include TPIDR2 in the signal context kselftest/arm64: Add TPIDR2 to the set of known signal context records kselftest/arm64: Add test case for TPIDR2 signal frame records Documentation/arm64/sme.rst | 3 + arch/arm64/include/uapi/asm/sigcontext.h | 8 ++ arch/arm64/kernel/signal.c | 59 ++++++++++++++ tools/testing/selftests/arm64/signal/.gitignore | 1 + .../selftests/arm64/signal/testcases/testcases.c | 4 + .../arm64/signal/testcases/tpidr2_siginfo.c | 90 ++++++++++++++++++++++ 6 files changed, 165 insertions(+) --- base-commit: 1b929c02afd37871d5afb9d498426f83432e71c2 change-id: 20221208-arm64-tpidr2-sig-8fbb93725d8e Best regards, -- Mark Brown <broonie(a)kernel.org>

1 year, 11 months

2
5
0 0

[PATCH linux-next] KVM: x86/xen: Remove unneeded semicolon

by zhang.songyi＠zte.com.cn

From: zhang songyi <zhang.songyi(a)zte.com.cn> The semicolon after the "}" is unneeded. Signed-off-by: zhang songyi <zhang.songyi(a)zte.com.cn> --- tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c b/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c index 721f6a693799..3e6ac82eba15 100644 --- a/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c +++ b/tools/testing/selftests/kvm/x86_64/xen_shinfo_test.c @@ -426,7 +426,7 @@ static void *juggle_shinfo_state(void *arg) __vm_ioctl(vm, KVM_XEN_HVM_SET_ATTR, &cache_init); __vm_ioctl(vm, KVM_XEN_HVM_SET_ATTR, &cache_destroy); pthread_testcancel(); - }; + } return NULL; } -- 2.15.2

1 year, 11 months

2
1
0 0

2024

2023

2022

2021

2020

2019

2018

2017

Linux-kselftest-mirror December 2022