Hi Patrice

Thanks for your time to test my patch.

On Mon, May 31, 2021 at 9:20 PM Patrice CHOTARD patrice.chotard@foss.st.com wrote:

Hi Dillon

On 5/14/21 1:02 PM, dillon.minfei@gmail.com wrote:

...

From: Dillon Min dillon.minfei@gmail.com

This seriese fix three i2c/clk bug for stm32 f4/f7

• kernel runing in sdram, i2c driver get data timeout
• ltdc clk turn off after kernel console active
• kernel hang in set ltdc clock rate

clk bug found on stm32f429/f469-disco board

Hi Patrice: below is the guide to verify the patch:

setup test env with following files(link at below 'files link'): [1] u-boot-dtb.bin [2] rootfs zip file (used in kernel initramfs) [3] u-boot's mkimage to create itb file [4] kernel config file [5] my itb with-or-without i2c patch

This patch based on kernel commit: 88b06399c9c766c283e070b022b5ceafa4f63f19

Note: panel-ilitek-ili9341.c is the driver which was submitted last year, but not get accepted. it's used to setup touch screen calibration, then test i2c.

create itb file(please correct path of 'data'): ./mkimage -f stm32.its stm32.itb

HW setup: console: PA9, PA10 usart0 serial@40011000 115200 8n1

-- flash u-boot.bin to stm32f429-disco on PC $ sudo openocd -f board/stm32f429discovery.cfg -c \ '{PATH-TO-YOUR-UBOOT}/u-boot-dtb.bin 0x08000000 exit reset'

-- setup kernel load bootargs at u-boot U-Boot > setenv bootargs 'console=tty0 console=ttySTM0,115200 root=/dev/ram rdinit=/linuxrc loglevel=8 fbcon=rotate:2' U-Boot > loady;bootm (download stm32.dtb or your kernel with itb format, or download zImage, dtb)

Thanks for these informations I was able to load and boot DTB and uImage directly in SDRAM as you suggested, i saw Linux logo and kernel log on the STM32F429-disco display, but i can't reach the login.

The last kernel log i got is :

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.13.0-rc1-00082-g9dbbd5cb6240-dirty (nxp11987@lmecxl0573.lme1 [ 0.000000] CPU: ARMv7-M [410fc241] revision 1 (ARMv7M), cr=00000000 [ 0.000000] CPU: unknown data cache, unknown instruction cache [ 0.000000] OF: fdt: Machine model: STMicroelectronics STM32F429i-DISCO board [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000090000000-0x00000000907fffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges

[...]

[ 2.637564] printk: console [ttySTM0] enabled [ 2.747984] panel-ilitek-ili9341 spi0.1: get optional vcc failed [ 2.758986] spi_stm32 40015000.spi: driver initialized [ 2.795733] i2c /dev entries driver [ 2.849955] stmpe-i2c 0-0041: stmpe811 detected, chip id: 0x811 [ 2.922030] stmpe-ts stmpe-ts: DMA mask not set [ 2.965729] input: stmpe-ts as /devices/platform/soc/40005c00.i2c/i2c-0/0-0041/stmpe-ts0 [ 2.991570] stm32f4-i2c 40005c00.i2c: STM32F4 I2C driver registered [ 3.058262] [drm] Initialized stm 1.0.0 20170330 for 40016800.display-controller on min0 [ 3.665951] panel-ilitek-ili9341 spi0.1: initialized display rgb interface [ 3.765208] Console: switching to colour frame buffer device 30x40 [ 4.014269] stm32-display 40016800.display-controller: [drm] fb0: stmdrmfb frame buffere [ 4.212737] Freeing unused kernel memory: 324K [ 4.287300] This architecture does not have kernel memory protection. [ 4.401202] Run /linuxrc as init process [ 4.478622] with arguments: [ 4.555069] /linuxrc [ 4.595406] with environment: [ 4.672213] HOME=/ [ 4.712511] TERM=linux [ 206.785289] random: crng init done

I guess you didn't add the rootfs to uImage I sent you. Could you post all the logs from u-boot startup to kernel log end.

If possible, you can try my suggestion. - tar -jxf stm32_rootfs.tar.bz2 - add stm32_rootfs to your kernel config( enable initramfs) - make O=YOUR_KERNEL_OUT zImage dtbs LOADADDR=0x90008000 - create itb file (combine dtb and kernel, initramfs) by mkimage ./mkimage -f stm32.its stm32.itb (before above command, make sure you correct stm32.its adapt to your env)

This process will make u-boot to load the kernel more simple.

Thanks.

Best Regards. Dillon

I can't test your I2C patch.

Patrice

...

-- setup ts_calibrate running env on stm32f429-disco / # export TSLIB_CONFFILE=/etc/ts.conf / # export TSLIB_TSDEVICE=/dev/input/event0 / # export TSLIB_CONSOLEDEVICE=none / # export TSLIB_FBDEVICE=/dev/fb0

-- clear screen / # ./fb

-- run ts_calibrate / # ts_calibrate (you can calibrate touchscreen now, and get below errors)

[ 113.942087] stmpe-i2c0-0041: failed to read regs 0x52: -110 [ 114.063598] stmpe-i2c 0-0041: failed to read reg 0x4b: -16 [ 114.185629] stmpe-i2c 0-0041: failed to read reg 0x40: -16 [ 114.307257] stmpe-i2c 0-0041: failed to write reg 0xb: -16

... with i2c patch applied, you will find below logs:

RAW---------------------> 3164 908 183 118.110884 TS_READ_RAW----> x = 3164, y =908, pressure = 183 RAW---------------------> 3166 922 126 118.138946 TS_READ_RAW----> x = 3166, y = 922, pressure = 126 ....

files link: https://drive.google.com/drive/folders/1qNbjChcB6UGtKzne2F5x9_WG_sZFyo3o?usp...

Dillon Min (4): drm/panel: Add ilitek ili9341 panel driver i2c: stm32f4: Fix stmpe811 get xyz data timeout issue clk: stm32: Fix stm32f429's ltdc driver hang in set clock rate clk: stm32: Fix ltdc's clock turn off by clk_disable_unused() after kernel startup

drivers/clk/clk-stm32f4.c | 10 +- drivers/gpu/drm/panel/Kconfig | 12 + drivers/gpu/drm/panel/Makefile | 1 + drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 1285 ++++++++++++++++++++++++++ drivers/i2c/busses/i2c-stm32f4.c | 12 +- 5 files changed, 1310 insertions(+), 10 deletions(-) create mode 100755 drivers/gpu/drm/panel/panel-ilitek-ili9341.c