Linaro-mm-sig August 2013

linaro-mm-sig@lists.linaro.org

26 participants
22 discussions

[PATCH v7 0/4] Device Tree support for CMA (Contiguous Memory Allocator)

by Marek Szyprowski

Hello, I thought that v6 series is really ready for merging, but I found today a stupid bug which broke compilation when CONFIG_CMA was not enabled, so another respin is needed. I've also took the opportunity and fixed some minor issues in the documentation (renamed all nodes to 'region') and rebased the patches onto Aneesh Kumar K.V patch queued earlier for merging. For more information, please refer to the V6 patches thread: http://thread.gmane.org/gmane.linux.ports.arm.kernel/261518 Best regards Marek Szyprowski Samsung R&D Institute Poland Changelog: v7: - fixed compilation break when CMA support has been disabled - rebased onto Aneesh Kumar K.V CMA patches queued earlier for merging - more cleanups in the binding documentation (thanks to Stephen Warren) v6: http://thread.gmane.org/gmane.linux.ports.arm.kernel/261518 - added support for 'status' property, so memory regions can be disabled like any other nodes - fixed issues pointed by Rob: removed annotations from function declarations and replaced macros with static inline functions. - restored of_scan_flat_dt_by_path() function to simplify reserved memory scanning function - the code now uses #size-cells/#address-cells properties from root node for interpreting 'reg' property in reserved memory regions - fixed some issues in dt binding documentation v5: http://thread.gmane.org/gmane.linux.ports.arm.kernel/259278 - renamed "contiguous-memory-region" compatibility string to "linux,contiguous-memory-region" (this one is really specific to Linux kernel implementation) - renamed "dma-memory-region" property to "memory-region" (suggested by Kumar Gala) - added support for #address-cells, #size-cells for memory regions (thanks to Rob Herring for suggestion) - removed generic code to scan specific path in flat device tree (cannot be used to fdt one-pass scan based initialization of memory regions with #address-cells and #size-cells parsing) - replaced dma_contiguous_set_default_area() and dma_contiguous_add_device() functions with dev_set_cma_area() call v4: http://thread.gmane.org/gmane.linux.ports.arm.kernel/256491 - corrected Devcie Tree mailing list address (resend) - moved back contiguous-memory bindings from /chosen/contiguous-memory to /memory nodes as suggested by Grant (see http://article.gmane.org/gmane.linux.drivers.devicetree/41030 for more details) - added support for DMA reserved memory with dma_declare_coherent() - moved code to drivers/of/of_reserved_mem.c - added generic code to scan specific path in flat device tree v3: http://thread.gmane.org/gmane.linux.drivers.devicetree/40013/ - fixed issues pointed by Laura and updated documentation v2: http://thread.gmane.org/gmane.linux.drivers.devicetree/34075 - moved contiguous-memory bindings from /memory to /chosen/contiguous-memory/ node to avoid spreading Linux specific parameters over the whole device tree definitions - added support for autoconfigured regions (use zero base) - fixes minor bugs v1: http://thread.gmane.org/gmane.linux.drivers.devicetree/30111/ - initial proposal Patch summary: Marek Szyprowski (4): drivers: dma-contiguous: clean source code and prepare for device tree drivers: of: add function to scan fdt nodes given by path drivers: of: add initialization code for dma reserved memory ARM: init: add support for reserved memory defined by device tree Documentation/devicetree/bindings/memory.txt | 168 +++++++++++++++++++++++++ arch/arm/include/asm/dma-contiguous.h | 1 - arch/arm/mm/init.c | 3 + arch/x86/include/asm/dma-contiguous.h | 1 - drivers/base/dma-contiguous.c | 119 +++++++----------- drivers/of/Kconfig | 6 + drivers/of/Makefile | 1 + drivers/of/fdt.c | 76 +++++++++++ drivers/of/of_reserved_mem.c | 175 ++++++++++++++++++++++++++ drivers/of/platform.c | 4 + include/asm-generic/dma-contiguous.h | 28 ----- include/linux/device.h | 2 +- include/linux/dma-contiguous.h | 62 ++++++++- include/linux/of_fdt.h | 3 + include/linux/of_reserved_mem.h | 14 +++ 15 files changed, 555 insertions(+), 108 deletions(-) create mode 100644 Documentation/devicetree/bindings/memory.txt create mode 100644 drivers/of/of_reserved_mem.c delete mode 100644 include/asm-generic/dma-contiguous.h create mode 100644 include/linux/of_reserved_mem.h -- 1.7.9.5

11 years, 2 months

[PATCH v3 0/2] Device Tree support for CMA (Contiguous Memory Allocator)

by Marek Szyprowski

Hello, This is a third version of my proposal for device tree integration for Contiguous Memory Allocator. Over 2 month has passed from the time I've posted the second version, but now some things about using /chosen device tree node has been clarified, so I expect to get this code merged soon this time. Just a few words for those who see this code for the first time: The proposed bindings allows to define contiguous memory regions of specified base address and size. Then, the defined regions can be assigned to the given device(s) by adding a property with a phanle to the defined contiguous memory region. From the device tree perspective that's all. Once the bindings are added, all the memory allocations from dma-mapping subsystem will be served from the defined contiguous memory regions. Contiguous Memory Allocator is a framework, which lets to provide a large contiguous memory buffers for (usually a multimedia) devices. The contiguous memory is reserved during early boot and then shared with kernel, which is allowed to allocate it for movable pages. Then, when device driver requests a contigouous buffer, the framework migrates movable pages out of contiguous region and gives it to the driver. When device driver frees the buffer, it is added to kernel memory pool again. For more information, please refer to commit c64be2bb1c6eb43c838b2c6d57 ("drivers: add Contiguous Memory Allocator") and d484864dd96e1830e76895 (CMA merge commit). Why we need device tree bindings for CMA at all? Older ARM kernels used so called board-based initialization. Those board files contained a definition of all hardware blocks available on the target system and particular kernel and driver software configuration selected by the board maintainer. In the new approach the board files will be removed completely and Device Tree approach is used to describe all hardware blocks available on the target system. By definition, the bindings should be software independent, so at least in theory it should be possible to use those bindings with other operating systems than Linux kernel. However we also need to pass somehow the information about kernel and device driver software-only configuration data, which were earlier encoded in the board file. For such data I decided to use /chosen node, where kernel command line has been already stored. Future bootloaders will allow to modify or replace particular nodes and one will be able to use custom /chosen node to configure his system. The proposed patches introduce /chosen/contiguous-memory node and related bindings, to avoid complicated encoding of CMA related configuration to kernel command line. Some rationale for using /chosen/ node for kernel configuration entities has been already suggested by Grant Likely in the following thread: http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/155296/focus=34363 Best regards Marek Szyprowski Samsung R&D Institute Poland Changelog: v3: - fixed issues pointed by Laura and updated documentation v2: http://thread.gmane.org/gmane.linux.drivers.devicetree/34075 - moved contiguous-memory bindings from /memory to /chosen/contiguous-memory/ node to avoid spreading Linux specific parameters over the whole device tree definitions - added support for autoconfigured regions (use zero base) - fixes minor bugs v1: http://thread.gmane.org/gmane.linux.drivers.devicetree/30111/ - initial proposal Patch summary: Marek Szyprowski (2): drivers: dma-contiguous: clean source code and prepare for device tree drivers: dma-contiguous: add initialization from device tree .../devicetree/bindings/contiguous-memory.txt | 94 ++++++ arch/arm/boot/dts/skeleton.dtsi | 7 +- drivers/base/dma-contiguous.c | 325 +++++++++++++------- include/asm-generic/dma-contiguous.h | 2 - include/linux/dma-contiguous.h | 32 +- 5 files changed, 352 insertions(+), 108 deletions(-) create mode 100644 Documentation/devicetree/bindings/contiguous-memory.txt -- 1.7.9.5

11 years, 3 months

[RFC 0/4] Atomic Display Framework

by Greg Hackmann

Hi, ADF is an experimental display framework that I designed after experimenting with a KMS-based hardware composer for Android. ADF started as an proof-of-concept implemented from scratch, so right now it's a separate framework rather than a patchstack on top of KMS. If there's community interest, moving forward I'd like to merge its functionality into KMS rather than keep it as a separate thing. I'm going to talk about ADF at the Android and Graphics session at Linux Plumbers. The documentation's not done but I wanted to post these patches to people a heads-up about ADF. If there's interest I can write up some more formal documentation ahead of Plumbers. I designed ADF to deal with some serious issues I had working with KMS: 1. The API is geared toward updating one object at a time. Android's graphics stack needs the entire screen updated atomically to avoid tearing, and on some SoCs to avoid wedging the display hardware. Rob Clark's atomic modeset patchset worked, but copy/update/commit design meant the driver had to keep a lot more internal state. 2. Some SoCs don't map well to KMS's CRTC + planes + encoders + connector model. At the time I was dealing with hardware where the blending engines didn't have their own framebuffer (they could only scan out constant colors or mix the output of other blocks), and you needed to gang several mixers together to drive high-res displays. 3. KMS doesn't support custom pixel formats, which a lot of newer SoCs use internally to cut down on bandwidth between hardware blocks. 4. KMS doesn't have a way to exchange sync fences. As a hack I managed to pass sync fences into the kernel as properties of the atomic pageflip, but there was no good way to get them back out of the kernel without a side channel. ADF represents display devices as collections of overlay engines and interfaces. Overlay engines (struct adf_overlay_engine) scan out images and interfaces (struct adf_interface) display those images. Overlay engines and interfaces can be connected in any n-to-n configuration that the hardware supports. Clients issue atomic updates to the screen by passing in a list of buffers (struct adf_buffer) consisting of dma-buf handles, sync fences, and basic metadata like format and size. If this involves composing multiple buffers, clients include a block of custom data describing the actual composition (scaling, z-order, blending, etc.) in a driver-specific format. Drivers provide hooks to validate these custom data blocks and commit the new configuration to hardware. ADF handles importing the dma-bufs and fences, waiting on incoming sync fences before committing, advancing the display's sync timeline, and releasing dma-bufs once they're removed from the screen. ADF represents pixel formats using DRM-style fourccs, and automatically sanity-checks buffer sizes when using one of the formats listed in drm_fourcc.h. Drivers can support custom fourccs if they provide hooks to validate buffers that use them. ADF also provides driver hooks for modesetting, managing and reporting hardware events like vsync, and changing DPMS state. These are documented in struct adf_{obj,overlay_engine,interface,device}_ops, and are similar to the equivalent DRM ops. Greg Hackmann (3): video: add atomic display framework video: adf: add display core helper video: adf: add memblock helper Laurent Pinchart (1): video: Add generic display entity core drivers/video/Kconfig | 2 + drivers/video/Makefile | 2 + drivers/video/adf/Kconfig | 15 + drivers/video/adf/Makefile | 14 + drivers/video/adf/adf.c | 1013 ++++++++++++++++++++++++++++++++++ drivers/video/adf/adf.h | 49 ++ drivers/video/adf/adf_client.c | 853 ++++++++++++++++++++++++++++ drivers/video/adf/adf_display.c | 123 +++++ drivers/video/adf/adf_fops.c | 982 ++++++++++++++++++++++++++++++++ drivers/video/adf/adf_fops.h | 37 ++ drivers/video/adf/adf_fops32.c | 217 ++++++++ drivers/video/adf/adf_fops32.h | 78 +++ drivers/video/adf/adf_memblock.c | 150 +++++ drivers/video/adf/adf_sysfs.c | 291 ++++++++++ drivers/video/adf/adf_sysfs.h | 33 ++ drivers/video/adf/adf_trace.h | 93 ++++ drivers/video/display/Kconfig | 4 + drivers/video/display/Makefile | 1 + drivers/video/display/display-core.c | 362 ++++++++++++ include/video/adf.h | 743 +++++++++++++++++++++++++ include/video/adf_client.h | 61 ++ include/video/adf_display.h | 31 ++ include/video/adf_format.h | 282 ++++++++++ include/video/adf_memblock.h | 20 + include/video/display.h | 150 +++++ 25 files changed, 5606 insertions(+) create mode 100644 drivers/video/adf/Kconfig create mode 100644 drivers/video/adf/Makefile create mode 100644 drivers/video/adf/adf.c create mode 100644 drivers/video/adf/adf.h create mode 100644 drivers/video/adf/adf_client.c create mode 100644 drivers/video/adf/adf_display.c create mode 100644 drivers/video/adf/adf_fops.c create mode 100644 drivers/video/adf/adf_fops.h create mode 100644 drivers/video/adf/adf_fops32.c create mode 100644 drivers/video/adf/adf_fops32.h create mode 100644 drivers/video/adf/adf_memblock.c create mode 100644 drivers/video/adf/adf_sysfs.c create mode 100644 drivers/video/adf/adf_sysfs.h create mode 100644 drivers/video/adf/adf_trace.h create mode 100644 drivers/video/display/Kconfig create mode 100644 drivers/video/display/Makefile create mode 100644 drivers/video/display/display-core.c create mode 100644 include/video/adf.h create mode 100644 include/video/adf_client.h create mode 100644 include/video/adf_display.h create mode 100644 include/video/adf_format.h create mode 100644 include/video/adf_memblock.h create mode 100644 include/video/display.h -- 1.8.0

11 years, 3 months

[PATCH v6 0/4] Device Tree support for CMA (Contiguous Memory Allocator)

by Marek Szyprowski

Hello, This is a sixth version of my proposal for device tree integration for reserved memory and Contiguous Memory Allocator. This time I've fixes more issues pointed by Rob Herring and added support for 'status' property. For more information, please check the change log at the end of the mail. Just a few words for those who see this code for the first time: The proposed bindings allows to define contiguous memory regions of specified base address and size. Then, the defined regions can be assigned to the given device(s) by adding a property with a phanle to the defined contiguous memory region. From the device tree perspective that's all. Once the bindings are added, all the memory allocations from dma-mapping subsystem will be served from the defined contiguous memory regions. Contiguous Memory Allocator is a framework, which lets to provide a large contiguous memory buffers for (usually a multimedia) devices. The contiguous memory is reserved during early boot and then shared with kernel, which is allowed to allocate it for movable pages. Then, when device driver requests a contigouous buffer, the framework migrates movable pages out of contiguous region and gives it to the driver. When device driver frees the buffer, it is added to kernel memory pool again. For more information, please refer to commit c64be2bb1c6eb43c838b2c6d57 ("drivers: add Contiguous Memory Allocator") and d484864dd96e1830e76895 (CMA merge commit). Why we need device tree bindings for CMA at all? Older ARM kernels used so called board-based initialization. Those board files contained a definition of all hardware blocks available on the target system and particular kernel and driver software configuration selected by the board maintainer. In the new approach the board files will be removed completely and Device Tree approach is used to describe all hardware blocks available on the target system. By definition, the bindings should be software independent, so at least in theory it should be possible to use those bindings with other operating systems than Linux kernel. Reserved memory configuration belongs to the grey area. It might depend on hardware restriction of the board or modules and low-level configuration done by bootloader. Putting reserved and contiguous memory regions to /memory node and having phandles to those regions in the device nodes however matches well with the device-tree typical style of linking devices with other resources like clocks, interrupts, regulators, power domains, etc. This is the main reason to use such approach instead of putting everything to /chosen node as it has been proposed in v2 and v3. However during the discussion at Linaro Connect in Dublin it has been decided that reserved memory is one of the _system_ property. Such system properties are not necessarily the hardware properties, but they are well-known and likely properties of the system that is running, so they can be encoded to device tree. This patch series tries to provide such encoding with the respect to the common device tree style of bindings and documentation. Best regards Marek Szyprowski Samsung R&D Institute Poland Changelog: v6: - added support for 'status' property, so memory regions can be disabled like any other nodes - fixed issues pointed by Rob: removed annotations from function declarations and replaced macros with static inline functions. - restored of_scan_flat_dt_by_path() function to simplify reserved memory scanning function - the code now uses #size-cells/#address-cells properties from root node for interpreting 'reg' property in reserved memory regions - fixed some issues in dt binding documentation v5: http://thread.gmane.org/gmane.linux.ports.arm.kernel/259278 - renamed "contiguous-memory-region" compatibility string to "linux,contiguous-memory-region" (this one is really specific to Linux kernel implementation) - renamed "dma-memory-region" property to "memory-region" (suggested by Kumar Gala) - added support for #address-cells, #size-cells for memory regions (thanks to Rob Herring for suggestion) - removed generic code to scan specific path in flat device tree (cannot be used to fdt one-pass scan based initialization of memory regions with #address-cells and #size-cells parsing) - replaced dma_contiguous_set_default_area() and dma_contiguous_add_device() functions with dev_set_cma_area() call v4: http://thread.gmane.org/gmane.linux.ports.arm.kernel/256491 - corrected Devcie Tree mailing list address (resend) - moved back contiguous-memory bindings from /chosen/contiguous-memory to /memory nodes as suggested by Grant (see http://article.gmane.org/gmane.linux.drivers.devicetree/41030 for more details) - added support for DMA reserved memory with dma_declare_coherent() - moved code to drivers/of/of_reserved_mem.c - added generic code to scan specific path in flat device tree v3: http://thread.gmane.org/gmane.linux.drivers.devicetree/40013/ - fixed issues pointed by Laura and updated documentation v2: http://thread.gmane.org/gmane.linux.drivers.devicetree/34075 - moved contiguous-memory bindings from /memory to /chosen/contiguous-memory/ node to avoid spreading Linux specific parameters over the whole device tree definitions - added support for autoconfigured regions (use zero base) - fixes minor bugs v1: http://thread.gmane.org/gmane.linux.drivers.devicetree/30111/ - initial proposal Patch summary: Marek Szyprowski (4): drivers: dma-contiguous: clean source code and prepare for device tree drivers: of: add function to scan fdt nodes given by path drivers: of: add initialization code for dma reserved memory ARM: init: add support for reserved memory defined by device tree Documentation/devicetree/bindings/memory.txt | 166 ++++++++++++++++++++++++ arch/arm/include/asm/dma-contiguous.h | 1 - arch/arm/mm/init.c | 3 + arch/x86/include/asm/dma-contiguous.h | 1 - drivers/base/dma-contiguous.c | 119 +++++++----------- drivers/of/Kconfig | 6 + drivers/of/Makefile | 1 + drivers/of/fdt.c | 76 +++++++++++ drivers/of/of_reserved_mem.c | 175 ++++++++++++++++++++++++++ drivers/of/platform.c | 5 + include/asm-generic/dma-contiguous.h | 28 ----- include/linux/dma-contiguous.h | 55 +++++++- include/linux/of_fdt.h | 3 + include/linux/of_reserved_mem.h | 14 +++ 14 files changed, 546 insertions(+), 107 deletions(-) create mode 100644 Documentation/devicetree/bindings/memory.txt create mode 100644 drivers/of/of_reserved_mem.c delete mode 100644 include/asm-generic/dma-contiguous.h create mode 100644 include/linux/of_reserved_mem.h -- 1.7.9.5

11 years, 3 months

[PATCH] dma-buf: Check return value of anon_inode_getfile

by Tuomas Tynkkynen

anon_inode_getfile might fail, so check its return value. Signed-off-by: Tuomas Tynkkynen <ttynkkynen(a)nvidia.com> --- drivers/base/dma-buf.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/base/dma-buf.c b/drivers/base/dma-buf.c index 1219ab7..2d5ac1a 100644 --- a/drivers/base/dma-buf.c +++ b/drivers/base/dma-buf.c @@ -133,7 +133,10 @@ struct dma_buf *dma_buf_export_named(void *priv, const struct dma_buf_ops *ops, dmabuf->exp_name = exp_name; file = anon_inode_getfile("dmabuf", &dma_buf_fops, dmabuf, flags); - + if (IS_ERR(file)) { + kfree(dmabuf); + return ERR_CAST(file); + } dmabuf->file = file; mutex_init(&dmabuf->lock); -- 1.8.1.5

11 years, 3 months

[PATCH] fence: dma-buf cross-device synchronization (v14)

by Maarten Lankhorst

A fence can be attached to a buffer which is being filled or consumed by hw, to allow userspace to pass the buffer without waiting to another device. For example, userspace can call page_flip ioctl to display the next frame of graphics after kicking the GPU but while the GPU is still rendering. The display device sharing the buffer with the GPU would attach a callback to get notified when the GPU's rendering-complete IRQ fires, to update the scan-out address of the display, without having to wake up userspace. A driver must allocate a fence context for each execution ring that can run in parallel. The function for this takes an argument with how many contexts to allocate: + fence_context_alloc() A fence is transient, one-shot deal. It is allocated and attached to one or more dma-buf's. When the one that attached it is done, with the pending operation, it can signal the fence: + fence_signal() To have a rough approximation whether a fence is fired, call: + fence_is_signaled() The dma-buf-mgr handles tracking, and waiting on, the fences associated with a dma-buf. The one pending on the fence can add an async callback: + fence_add_callback() The callback can optionally be cancelled with: + fence_remove_callback() To wait synchronously, optionally with a timeout: + fence_wait() + fence_wait_timeout() A default software-only implementation is provided, which can be used by drivers attaching a fence to a buffer when they have no other means for hw sync. But a memory backed fence is also envisioned, because it is common that GPU's can write to, or poll on some memory location for synchronization. For example: fence = custom_get_fence(...); if ((seqno_fence = to_seqno_fence(fence)) != NULL) { dma_buf *fence_buf = fence->sync_buf; get_dma_buf(fence_buf); ... tell the hw the memory location to wait ... custom_wait_on(fence_buf, fence->seqno_ofs, fence->seqno); } else { /* fall-back to sw sync * / fence_add_callback(fence, my_cb); } On SoC platforms, if some other hw mechanism is provided for synchronizing between IP blocks, it could be supported as an alternate implementation with it's own fence ops in a similar way. enable_signaling callback is used to provide sw signaling in case a cpu waiter is requested or no compatible hardware signaling could be used. The intention is to provide a userspace interface (presumably via eventfd) later, to be used in conjunction with dma-buf's mmap support for sw access to buffers (or for userspace apps that would prefer to do their own synchronization). v1: Original v2: After discussion w/ danvet and mlankhorst on #dri-devel, we decided that dma-fence didn't need to care about the sw->hw signaling path (it can be handled same as sw->sw case), and therefore the fence->ops can be simplified and more handled in the core. So remove the signal, add_callback, cancel_callback, and wait ops, and replace with a simple enable_signaling() op which can be used to inform a fence supporting hw->hw signaling that one or more devices which do not support hw signaling are waiting (and therefore it should enable an irq or do whatever is necessary in order that the CPU is notified when the fence is passed). v3: Fix locking fail in attach_fence() and get_fence() v4: Remove tie-in w/ dma-buf.. after discussion w/ danvet and mlankorst we decided that we need to be able to attach one fence to N dma-buf's, so using the list_head in dma-fence struct would be problematic. v5: [ Maarten Lankhorst ] Updated for dma-bikeshed-fence and dma-buf-manager. v6: [ Maarten Lankhorst ] I removed dma_fence_cancel_callback and some comments about checking if fence fired or not. This is broken by design. waitqueue_active during destruction is now fatal, since the signaller should be holding a reference in enable_signalling until it signalled the fence. Pass the original dma_fence_cb along, and call __remove_wait in the dma_fence_callback handler, so that no cleanup needs to be performed. v7: [ Maarten Lankhorst ] Set cb->func and only enable sw signaling if fence wasn't signaled yet, for example for hardware fences that may choose to signal blindly. v8: [ Maarten Lankhorst ] Tons of tiny fixes, moved __dma_fence_init to header and fixed include mess. dma-fence.h now includes dma-buf.h All members are now initialized, so kmalloc can be used for allocating a dma-fence. More documentation added. v9: Change compiler bitfields to flags, change return type of enable_signaling to bool. Rework dma_fence_wait. Added dma_fence_is_signaled and dma_fence_wait_timeout. s/dma// and change exports to non GPL. Added fence_is_signaled and fence_enable_sw_signaling calls, add ability to override default wait operation. v10: remove event_queue, use a custom list, export try_to_wake_up from scheduler. Remove fence lock and use a global spinlock instead, this should hopefully remove all the locking headaches I was having on trying to implement this. enable_signaling is called with this lock held. v11: Use atomic ops for flags, lifting the need for some spin_lock_irqsaves. However I kept the guarantee that after fence_signal returns, it is guaranteed that enable_signaling has either been called to completion, or will not be called any more. Add contexts and seqno to base fence implementation. This allows you to wait for less fences, by testing for seqno + signaled, and then only wait on the later fence. Add FENCE_TRACE, FENCE_WARN, and FENCE_ERR. This makes debugging easier. An CONFIG_DEBUG_FENCE will be added to turn off the FENCE_TRACE spam, and another runtime option can turn it off at runtime. v12: Add CONFIG_FENCE_TRACE. Add missing documentation for the fence->context and fence->seqno members. v13: Fixup CONFIG_FENCE_TRACE kconfig description. Move fence_context_alloc to fence. Simplify fence_later. Kill priv member to fence_cb. v14: Remove priv argument from fence_add_callback, oops! Signed-off-by: Maarten Lankhorst <maarten.lankhorst(a)canonical.com> --- Documentation/DocBook/device-drivers.tmpl | 2 drivers/base/Kconfig | 10 + drivers/base/Makefile | 2 drivers/base/fence.c | 311 ++++++++++++++++++++++++++ include/linux/fence.h | 344 +++++++++++++++++++++++++++++ 5 files changed, 668 insertions(+), 1 deletion(-) create mode 100644 drivers/base/fence.c create mode 100644 include/linux/fence.h diff --git a/Documentation/DocBook/device-drivers.tmpl b/Documentation/DocBook/device-drivers.tmpl index fe397f9..95d0db9 100644 --- a/Documentation/DocBook/device-drivers.tmpl +++ b/Documentation/DocBook/device-drivers.tmpl @@ -126,6 +126,8 @@ X!Edrivers/base/interface.c </sect1> <sect1><title>Device Drivers DMA Management</title> !Edrivers/base/dma-buf.c +!Edrivers/base/fence.c +!Iinclude/linux/fence.h !Edrivers/base/reservation.c !Iinclude/linux/reservation.h !Edrivers/base/dma-coherent.c diff --git a/drivers/base/Kconfig b/drivers/base/Kconfig index 5daa259..2bf0add 100644 --- a/drivers/base/Kconfig +++ b/drivers/base/Kconfig @@ -200,6 +200,16 @@ config DMA_SHARED_BUFFER APIs extension; the file's descriptor can then be passed on to other driver. +config FENCE_TRACE + bool "Enable verbose FENCE_TRACE messages" + default n + depends on DMA_SHARED_BUFFER + help + Enable the FENCE_TRACE printks. This will add extra + spam to the console log, but will make it easier to diagnose + lockup related problems for dma-buffers shared across multiple + devices. + config CMA bool "Contiguous Memory Allocator" depends on HAVE_DMA_CONTIGUOUS && HAVE_MEMBLOCK diff --git a/drivers/base/Makefile b/drivers/base/Makefile index 48029aa..8a55cb9 100644 --- a/drivers/base/Makefile +++ b/drivers/base/Makefile @@ -10,7 +10,7 @@ obj-$(CONFIG_CMA) += dma-contiguous.o obj-y += power/ obj-$(CONFIG_HAS_DMA) += dma-mapping.o obj-$(CONFIG_HAVE_GENERIC_DMA_COHERENT) += dma-coherent.o -obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf.o reservation.o +obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf.o fence.o reservation.o obj-$(CONFIG_ISA) += isa.o obj-$(CONFIG_FW_LOADER) += firmware_class.o obj-$(CONFIG_NUMA) += node.o diff --git a/drivers/base/fence.c b/drivers/base/fence.c new file mode 100644 index 0000000..a95df7d --- /dev/null +++ b/drivers/base/fence.c @@ -0,0 +1,311 @@ +/* + * Fence mechanism for dma-buf and to allow for asynchronous dma access + * + * Copyright (C) 2012 Canonical Ltd + * Copyright (C) 2012 Texas Instruments + * + * Authors: + * Rob Clark <robdclark(a)gmail.com> + * Maarten Lankhorst <maarten.lankhorst(a)canonical.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/slab.h> +#include <linux/export.h> +#include <linux/fence.h> + +/** + * fence context counter: each execution context should have its own + * fence context, this allows checking if fences belong to the same + * context or not. One device can have multiple separate contexts, + * and they're used if some engine can run independently of another. + */ +static atomic_t fence_context_counter = ATOMIC_INIT(0); + +/** + * fence_context_alloc - allocate an array of fence contexts + * @num: [in] amount of contexts to allocate + * + * This function will return the first index of the number of fences allocated. + * The fence context is used for setting fence->context to a unique number. + */ +unsigned fence_context_alloc(unsigned num) +{ + BUG_ON(!num); + return atomic_add_return(num, &fence_context_counter) - num; +} +EXPORT_SYMBOL(fence_context_alloc); + +int __fence_signal(struct fence *fence) +{ + struct fence_cb *cur, *tmp; + int ret = 0; + + if (WARN_ON(!fence)) + return -EINVAL; + + if (test_and_set_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) { + ret = -EINVAL; + + /* + * we might have raced with the unlocked fence_signal, + * still run through all callbacks + */ + } + + list_for_each_entry_safe(cur, tmp, &fence->cb_list, node) { + list_del_init(&cur->node); + cur->func(fence, cur); + } + return ret; +} +EXPORT_SYMBOL(__fence_signal); + +/** + * fence_signal - signal completion of a fence + * @fence: the fence to signal + * + * Signal completion for software callbacks on a fence, this will unblock + * fence_wait() calls and run all the callbacks added with + * fence_add_callback(). Can be called multiple times, but since a fence + * can only go from unsignaled to signaled state, it will only be effective + * the first time. + */ +int fence_signal(struct fence *fence) +{ + unsigned long flags; + + if (!fence || test_and_set_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return -EINVAL; + + if (test_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags)) { + struct fence_cb *cur, *tmp; + + spin_lock_irqsave(fence->lock, flags); + list_for_each_entry_safe(cur, tmp, &fence->cb_list, node) { + list_del_init(&cur->node); + cur->func(fence, cur); + } + spin_unlock_irqrestore(fence->lock, flags); + } + return 0; +} +EXPORT_SYMBOL(fence_signal); + +void release_fence(struct kref *kref) +{ + struct fence *fence = + container_of(kref, struct fence, refcount); + + BUG_ON(!list_empty(&fence->cb_list)); + + if (fence->ops->release) + fence->ops->release(fence); + else + kfree(fence); +} +EXPORT_SYMBOL(release_fence); + +/** + * fence_enable_sw_signaling - enable signaling on fence + * @fence: [in] the fence to enable + * + * this will request for sw signaling to be enabled, to make the fence + * complete as soon as possible + */ +void fence_enable_sw_signaling(struct fence *fence) +{ + unsigned long flags; + + if (!test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags) && + !test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) { + spin_lock_irqsave(fence->lock, flags); + + if (!fence->ops->enable_signaling(fence)) + __fence_signal(fence); + + spin_unlock_irqrestore(fence->lock, flags); + } +} +EXPORT_SYMBOL(fence_enable_sw_signaling); + +/** + * fence_add_callback - add a callback to be called when the fence + * is signaled + * @fence: [in] the fence to wait on + * @cb: [in] the callback to register + * @func: [in] the function to call + * + * cb will be initialized by fence_add_callback, no initialization + * by the caller is required. Any number of callbacks can be registered + * to a fence, but a callback can only be registered to one fence at a time. + * + * Note that the callback can be called from an atomic context. If + * fence is already signaled, this function will return -ENOENT (and + * *not* call the callback) + * + * Add a software callback to the fence. Same restrictions apply to + * refcount as it does to fence_wait, however the caller doesn't need to + * keep a refcount to fence afterwards: when software access is enabled, + * the creator of the fence is required to keep the fence alive until + * after it signals with fence_signal. The callback itself can be called + * from irq context. + * + */ +int fence_add_callback(struct fence *fence, struct fence_cb *cb, + fence_func_t func) +{ + unsigned long flags; + int ret = 0; + bool was_set; + + if (WARN_ON(!fence || !func)) + return -EINVAL; + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return -ENOENT; + + spin_lock_irqsave(fence->lock, flags); + + was_set = test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags); + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + ret = -ENOENT; + else if (!was_set && !fence->ops->enable_signaling(fence)) { + __fence_signal(fence); + ret = -ENOENT; + } + + if (!ret) { + cb->func = func; + list_add_tail(&cb->node, &fence->cb_list); + } + spin_unlock_irqrestore(fence->lock, flags); + + return ret; +} +EXPORT_SYMBOL(fence_add_callback); + +/** + * fence_remove_callback - remove a callback from the signaling list + * @fence: [in] the fence to wait on + * @cb: [in] the callback to remove + * + * Remove a previously queued callback from the fence. This function returns + * true is the callback is succesfully removed, or false if the fence has + * already been signaled. + * + * *WARNING*: + * Cancelling a callback should only be done if you really know what you're + * doing, since deadlocks and race conditions could occur all too easily. For + * this reason, it should only ever be done on hardware lockup recovery, + * with a reference held to the fence. + */ +bool +fence_remove_callback(struct fence *fence, struct fence_cb *cb) +{ + unsigned long flags; + bool ret; + + spin_lock_irqsave(fence->lock, flags); + + ret = !list_empty(&cb->node); + if (ret) + list_del_init(&cb->node); + + spin_unlock_irqrestore(fence->lock, flags); + + return ret; +} +EXPORT_SYMBOL(fence_remove_callback); + +struct default_wait_cb { + struct fence_cb base; + struct task_struct *task; +}; + +static void +fence_default_wait_cb(struct fence *fence, struct fence_cb *cb) +{ + struct default_wait_cb *wait = + container_of(cb, struct default_wait_cb, base); + + try_to_wake_up(wait->task, TASK_NORMAL, 0); +} + +/** + * fence_default_wait - default sleep until the fence gets signaled + * or until timeout elapses + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * @timeout: [in] timeout value in jiffies, or MAX_SCHEDULE_TIMEOUT + * + * Returns -ERESTARTSYS if interrupted, 0 if the wait timed out, or the + * remaining timeout in jiffies on success. + */ +long +fence_default_wait(struct fence *fence, bool intr, signed long timeout) +{ + struct default_wait_cb cb; + unsigned long flags; + long ret = timeout; + bool was_set; + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return timeout; + + spin_lock_irqsave(fence->lock, flags); + + if (intr && signal_pending(current)) { + ret = -ERESTARTSYS; + goto out; + } + + was_set = test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags); + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + goto out; + + if (!was_set && !fence->ops->enable_signaling(fence)) { + __fence_signal(fence); + goto out; + } + + cb.base.func = fence_default_wait_cb; + cb.task = current; + list_add(&cb.base.node, &fence->cb_list); + + while (!test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags) && ret > 0) { + if (intr) + __set_current_state(TASK_INTERRUPTIBLE); + else + __set_current_state(TASK_UNINTERRUPTIBLE); + spin_unlock_irqrestore(fence->lock, flags); + + ret = schedule_timeout(ret); + + spin_lock_irqsave(fence->lock, flags); + if (ret > 0 && intr && signal_pending(current)) + ret = -ERESTARTSYS; + } + + if (!list_empty(&cb.base.node)) + list_del(&cb.base.node); + __set_current_state(TASK_RUNNING); + +out: + spin_unlock_irqrestore(fence->lock, flags); + return ret; +} +EXPORT_SYMBOL(fence_default_wait); diff --git a/include/linux/fence.h b/include/linux/fence.h new file mode 100644 index 0000000..3ce2155 --- /dev/null +++ b/include/linux/fence.h @@ -0,0 +1,344 @@ +/* + * Fence mechanism for dma-buf to allow for asynchronous dma access + * + * Copyright (C) 2012 Canonical Ltd + * Copyright (C) 2012 Texas Instruments + * + * Authors: + * Rob Clark <robdclark(a)gmail.com> + * Maarten Lankhorst <maarten.lankhorst(a)canonical.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef __LINUX_FENCE_H +#define __LINUX_FENCE_H + +#include <linux/err.h> +#include <linux/wait.h> +#include <linux/list.h> +#include <linux/bitops.h> +#include <linux/kref.h> +#include <linux/sched.h> +#include <linux/printk.h> + +struct fence; +struct fence_ops; +struct fence_cb; + +/** + * struct fence - software synchronization primitive + * @refcount: refcount for this fence + * @ops: fence_ops associated with this fence + * @cb_list: list of all callbacks to call + * @lock: spin_lock_irqsave used for locking + * @context: execution context this fence belongs to, returned by + * fence_context_alloc() + * @seqno: the sequence number of this fence inside the execution context, + * can be compared to decide which fence would be signaled later. + * @flags: A mask of FENCE_FLAG_* defined below + * + * the flags member must be manipulated and read using the appropriate + * atomic ops (bit_*), so taking the spinlock will not be needed most + * of the time. + * + * FENCE_FLAG_SIGNALED_BIT - fence is already signaled + * FENCE_FLAG_ENABLE_SIGNAL_BIT - enable_signaling might have been called* + * FENCE_FLAG_USER_BITS - start of the unused bits, can be used by the + * implementer of the fence for its own purposes. Can be used in different + * ways by different fence implementers, so do not rely on this. + * + * *) Since atomic bitops are used, this is not guaranteed to be the case. + * Particularly, if the bit was set, but fence_signal was called right + * before this bit was set, it would have been able to set the + * FENCE_FLAG_SIGNALED_BIT, before enable_signaling was called. + * Adding a check for FENCE_FLAG_SIGNALED_BIT after setting + * FENCE_FLAG_ENABLE_SIGNAL_BIT closes this race, and makes sure that + * after fence_signal was called, any enable_signaling call will have either + * been completed, or never called at all. + */ +struct fence { + struct kref refcount; + const struct fence_ops *ops; + struct list_head cb_list; + spinlock_t *lock; + unsigned context, seqno; + unsigned long flags; +}; + +enum fence_flag_bits { + FENCE_FLAG_SIGNALED_BIT, + FENCE_FLAG_ENABLE_SIGNAL_BIT, + FENCE_FLAG_USER_BITS, /* must always be last member */ +}; + +typedef void (*fence_func_t)(struct fence *fence, struct fence_cb *cb); + +/** + * struct fence_cb - callback for fence_add_callback + * @node: used by fence_add_callback to append this struct to fence::cb_list + * @func: fence_func_t to call + * @priv: value of priv to pass to function + * + * This struct will be initialized by fence_add_callback, additional + * data can be passed along by embedding fence_cb in another struct. + */ +struct fence_cb { + struct list_head node; + fence_func_t func; +}; + +/** + * struct fence_ops - operations implemented for fence + * @enable_signaling: enable software signaling of fence + * @signaled: [optional] peek whether the fence is signaled, can be null + * @wait: custom wait implementation + * @release: [optional] called on destruction of fence, can be null + * + * Notes on enable_signaling: + * For fence implementations that have the capability for hw->hw + * signaling, they can implement this op to enable the necessary + * irqs, or insert commands into cmdstream, etc. This is called + * in the first wait() or add_callback() path to let the fence + * implementation know that there is another driver waiting on + * the signal (ie. hw->sw case). + * + * This function can be called called from atomic context, but not + * from irq context, so normal spinlocks can be used. + * + * A return value of false indicates the fence already passed, + * or some failure occured that made it impossible to enable + * signaling. True indicates succesful enabling. + * + * Calling fence_signal before enable_signaling is called allows + * for a tiny race window in which enable_signaling is called during, + * before, or after fence_signal. To fight this, it is recommended + * that before enable_signaling returns true an extra reference is + * taken on the fence, to be released when the fence is signaled. + * This will mean fence_signal will still be called twice, but + * the second time will be a noop since it was already signaled. + * + * Notes on wait: + * Must not be NULL, set to fence_default_wait for default implementation. + * the fence_default_wait implementation should work for any fence, as long + * as enable_signaling works correctly. + * + * Must return -ERESTARTSYS if the wait is intr = true and the wait was + * interrupted, and remaining jiffies if fence has signaled, or 0 if wait + * timed out. Can also return other error values on custom implementations, + * which should be treated as if the fence is signaled. For example a hardware + * lockup could be reported like that. + * + * Notes on release: + * Can be NULL, this function allows additional commands to run on + * destruction of the fence. Can be called from irq context. + * If pointer is set to NULL, kfree will get called instead. + */ + +struct fence_ops { + bool (*enable_signaling)(struct fence *fence); + bool (*signaled)(struct fence *fence); + long (*wait)(struct fence *fence, bool intr, signed long timeout); + void (*release)(struct fence *fence); +}; + +/** + * __fence_init - Initialize a custom fence. + * @fence: [in] the fence to initialize + * @ops: [in] the fence_ops for operations on this fence + * @lock: [in] the irqsafe spinlock to use for locking this fence + * @context: [in] the execution context this fence is run on + * @seqno: [in] a linear increasing sequence number for this context + * + * Initializes an allocated fence, the caller doesn't have to keep its + * refcount after committing with this fence, but it will need to hold a + * refcount again if fence_ops.enable_signaling gets called. This can + * be used for other implementing other types of fence. + * + * context and seqno are used for easy comparison between fences, allowing + * to check which fence is later by simply using fence_later. + */ +static inline void +__fence_init(struct fence *fence, const struct fence_ops *ops, + spinlock_t *lock, unsigned context, unsigned seqno) +{ + BUG_ON(!ops || !lock || !ops->enable_signaling || !ops->wait); + + kref_init(&fence->refcount); + fence->ops = ops; + INIT_LIST_HEAD(&fence->cb_list); + fence->lock = lock; + fence->context = context; + fence->seqno = seqno; + fence->flags = 0UL; +} + +/** + * fence_get - increases refcount of the fence + * @fence: [in] fence to increase refcount of + */ +static inline void fence_get(struct fence *fence) +{ + if (WARN_ON(!fence)) + return; + kref_get(&fence->refcount); +} + +extern void release_fence(struct kref *kref); + +/** + * fence_put - decreases refcount of the fence + * @fence: [in] fence to reduce refcount of + */ +static inline void fence_put(struct fence *fence) +{ + if (WARN_ON(!fence)) + return; + kref_put(&fence->refcount, release_fence); +} + +int fence_signal(struct fence *fence); +int __fence_signal(struct fence *fence); +long fence_default_wait(struct fence *fence, bool intr, signed long timeout); +int fence_add_callback(struct fence *fence, struct fence_cb *cb, + fence_func_t func); +bool fence_remove_callback(struct fence *fence, struct fence_cb *cb); +void fence_enable_sw_signaling(struct fence *fence); + +/** + * fence_is_signaled - Return an indication if the fence is signaled yet. + * @fence: [in] the fence to check + * + * Returns true if the fence was already signaled, false if not. Since this + * function doesn't enable signaling, it is not guaranteed to ever return true + * If fence_add_callback, fence_wait or fence_enable_sw_signaling + * haven't been called before. + * + * It's recommended for seqno fences to call fence_signal when the + * operation is complete, it makes it possible to prevent issues from + * wraparound between time of issue and time of use by checking the return + * value of this function before calling hardware-specific wait instructions. + */ +static inline bool +fence_is_signaled(struct fence *fence) +{ + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return true; + + if (fence->ops->signaled && fence->ops->signaled(fence)) { + fence_signal(fence); + return true; + } + + return false; +} + +/** + * fence_later - return the chronologically later fence + * @f1: [in] the first fence from the same context + * @f2: [in] the second fence from the same context + * + * Returns NULL if both fences are signaled, otherwise the fence that would be + * signaled last. Both fences must be from the same context, since a seqno is + * not re-used across contexts. + */ +static inline struct fence *fence_later(struct fence *f1, struct fence *f2) +{ + BUG_ON(f1->context != f2->context); + + /* + * can't check just FENCE_FLAG_SIGNALED_BIT here, it may never have been + * set called if enable_signaling wasn't, and enabling that here is + * overkill. + */ + if (f2->seqno - f1->seqno <= INT_MAX) + return fence_is_signaled(f2) ? NULL : f2; + else + return fence_is_signaled(f1) ? NULL : f1; +} + +/** + * fence_wait_timeout - sleep until the fence gets signaled + * or until timeout elapses + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * @timeout: [in] timeout value in jiffies, or MAX_SCHEDULE_TIMEOUT + * + * Returns -ERESTARTSYS if interrupted, 0 if the wait timed out, or the + * remaining timeout in jiffies on success. Other error values may be + * returned on custom implementations. + * + * Performs a synchronous wait on this fence. It is assumed the caller + * directly or indirectly (buf-mgr between reservation and committing) + * holds a reference to the fence, otherwise the fence might be + * freed before return, resulting in undefined behavior. + */ +static inline long +fence_wait_timeout(struct fence *fence, bool intr, signed long timeout) +{ + if (WARN_ON(timeout < 0)) + return -EINVAL; + + return fence->ops->wait(fence, intr, timeout); +} + +/** + * fence_wait - sleep until the fence gets signaled + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * + * This function will return -ERESTARTSYS if interrupted by a signal, + * or 0 if the fence was signaled. Other error values may be + * returned on custom implementations. + * + * Performs a synchronous wait on this fence. It is assumed the caller + * directly or indirectly (buf-mgr between reservation and committing) + * holds a reference to the fence, otherwise the fence might be + * freed before return, resulting in undefined behavior. + */ +static inline long fence_wait(struct fence *fence, bool intr) +{ + long ret; + + /* Since fence_wait_timeout cannot timeout with + * MAX_SCHEDULE_TIMEOUT, only valid return values are + * -ERESTARTSYS and MAX_SCHEDULE_TIMEOUT. + */ + ret = fence_wait_timeout(fence, intr, MAX_SCHEDULE_TIMEOUT); + + return ret < 0 ? ret : 0; +} + +unsigned fence_context_alloc(unsigned num); + +#define FENCE_TRACE(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + if (config_enabled(CONFIG_FENCE_TRACE)) \ + pr_info("f %u#%u: " fmt, \ + __ff->context, __ff->seqno, ##args); \ + } while (0) + +#define FENCE_WARN(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + pr_warn("f %u#%u: " fmt, __ff->context, __ff->seqno, ##args); \ + } while (0) + +#define FENCE_ERR(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + pr_err("f %u#%u: " fmt, __ff->context, __ff->seqno, ##args); \ + } while (0) + +#endif /* __LINUX_FENCE_H */

11 years, 4 months

[PATCH v5 0/3] Device Tree support for CMA (Contiguous Memory Allocator)

by Marek Szyprowski

Hello, This is a fifth version of my proposal for device tree integration for reserved memory and Contiguous Memory Allocator. I've fixed issues pointed by Michal Nazarewicz, Rob Herring and Kumar Gala. For more information, please check the change log at the end of the mail. In fourth version of this patch set, after the comments from Grant Likely I moved back memory region definitions back to /memory node (as it was in the first version of this proposal). I've also extended the code and made it more generic, added support for so called reserved dma memory (special dma memory regions created by dma_alloc_coherent() function, for exclusive usage for dma allocation for the given device). Just a few words for those who see this code for the first time: The proposed bindings allows to define contiguous memory regions of specified base address and size. Then, the defined regions can be assigned to the given device(s) by adding a property with a phanle to the defined contiguous memory region. From the device tree perspective that's all. Once the bindings are added, all the memory allocations from dma-mapping subsystem will be served from the defined contiguous memory regions. Contiguous Memory Allocator is a framework, which lets to provide a large contiguous memory buffers for (usually a multimedia) devices. The contiguous memory is reserved during early boot and then shared with kernel, which is allowed to allocate it for movable pages. Then, when device driver requests a contigouous buffer, the framework migrates movable pages out of contiguous region and gives it to the driver. When device driver frees the buffer, it is added to kernel memory pool again. For more information, please refer to commit c64be2bb1c6eb43c838b2c6d57 ("drivers: add Contiguous Memory Allocator") and d484864dd96e1830e76895 (CMA merge commit). Why we need device tree bindings for CMA at all? Older ARM kernels used so called board-based initialization. Those board files contained a definition of all hardware blocks available on the target system and particular kernel and driver software configuration selected by the board maintainer. In the new approach the board files will be removed completely and Device Tree approach is used to describe all hardware blocks available on the target system. By definition, the bindings should be software independent, so at least in theory it should be possible to use those bindings with other operating systems than Linux kernel. Reserved memory configuration belongs to the grey area. It might depend on hardware restriction of the board or modules and low-level configuration done by bootloader. Putting reserved and contiguous memory regions to /memory node and having phandles to those regions in the device nodes however matches well with the device-tree typical style of linking devices with other resources like clocks, interrupts, regulators, power domains, etc. This is the main reason to use such approach instead of putting everything to /chosen node as it has been proposed in v2 and v3. Best regards Marek Szyprowski Samsung R&D Institute Poland Changelog: v5: - renamed "contiguous-memory-region" compatibility string to "linux,contiguous-memory-region" (this one is really specific to Linux kernel implementation) - renamed "dma-memory-region" property to "memory-region" (suggested by Kumar Gala) - added support for #address-cells, #size-cells for memory regions (thanks to Rob Herring for suggestion) - removed generic code to scan specific path in flat device tree (cannot be used to fdt one-pass scan based initialization of memory regions with #address-cells and #size-cells parsing) - replaced dma_contiguous_set_default_area() and dma_contiguous_add_device() functions with dev_set_cma_area() call v4: http://thread.gmane.org/gmane.linux.ports.arm.kernel/256491 - corrected Devcie Tree mailing list address (resend) - moved back contiguous-memory bindings from /chosen/contiguous-memory to /memory nodes as suggested by Grant (see http://article.gmane.org/gmane.linux.drivers.devicetree/41030 for more details) - added support for DMA reserved memory with dma_declare_coherent() - moved code to drivers/of/of_reserved_mem.c - added generic code to scan specific path in flat device tree v3: http://thread.gmane.org/gmane.linux.drivers.devicetree/40013/ - fixed issues pointed by Laura and updated documentation v2: http://thread.gmane.org/gmane.linux.drivers.devicetree/34075 - moved contiguous-memory bindings from /memory to /chosen/contiguous-memory/ node to avoid spreading Linux specific parameters over the whole device tree definitions - added support for autoconfigured regions (use zero base) - fixes minor bugs v1: http://thread.gmane.org/gmane.linux.drivers.devicetree/30111/ - initial proposal Patch summary: Marek Szyprowski (3): drivers: dma-contiguous: clean source code and prepare for device tree drivers: of: add initialization code for dma reserved memory ARM: init: add support for reserved memory defined by device tree Documentation/devicetree/bindings/memory.txt | 152 ++++++++++++++++++++ arch/arm/include/asm/dma-contiguous.h | 1 - arch/arm/mm/init.c | 3 + arch/x86/include/asm/dma-contiguous.h | 1 - drivers/base/dma-contiguous.c | 119 ++++++---------- drivers/of/Kconfig | 6 + drivers/of/Makefile | 1 + drivers/of/of_reserved_mem.c | 197 ++++++++++++++++++++++++++ drivers/of/platform.c | 5 + include/asm-generic/dma-contiguous.h | 28 ---- include/linux/dma-contiguous.h | 55 ++++++- include/linux/of_reserved_mem.h | 14 ++ 12 files changed, 475 insertions(+), 107 deletions(-) create mode 100644 Documentation/devicetree/bindings/memory.txt create mode 100644 drivers/of/of_reserved_mem.c delete mode 100644 include/asm-generic/dma-contiguous.h create mode 100644 include/linux/of_reserved_mem.h -- 1.7.9.5

11 years, 4 months

[RFC PATCH] fence: dma-buf cross-device synchronization (v12)

by Maarten Lankhorst

A fence can be attached to a buffer which is being filled or consumed by hw, to allow userspace to pass the buffer without waiting to another device. For example, userspace can call page_flip ioctl to display the next frame of graphics after kicking the GPU but while the GPU is still rendering. The display device sharing the buffer with the GPU would attach a callback to get notified when the GPU's rendering-complete IRQ fires, to update the scan-out address of the display, without having to wake up userspace. A driver must allocate a fence context for each execution ring that can run in parallel. The function for this takes an argument with how many contexts to allocate: + fence_context_alloc() A fence is transient, one-shot deal. It is allocated and attached to one or more dma-buf's. When the one that attached it is done, with the pending operation, it can signal the fence: + fence_signal() To have a rough approximation whether a fence is fired, call: + fence_is_signaled() The dma-buf-mgr handles tracking, and waiting on, the fences associated with a dma-buf. The one pending on the fence can add an async callback: + fence_add_callback() The callback can optionally be cancelled with: + fence_remove_callback() To wait synchronously, optionally with a timeout: + fence_wait() + fence_wait_timeout() A default software-only implementation is provided, which can be used by drivers attaching a fence to a buffer when they have no other means for hw sync. But a memory backed fence is also envisioned, because it is common that GPU's can write to, or poll on some memory location for synchronization. For example: fence = custom_get_fence(...); if ((seqno_fence = to_seqno_fence(fence)) != NULL) { dma_buf *fence_buf = fence->sync_buf; get_dma_buf(fence_buf); ... tell the hw the memory location to wait ... custom_wait_on(fence_buf, fence->seqno_ofs, fence->seqno); } else { /* fall-back to sw sync * / fence_add_callback(fence, my_cb); } On SoC platforms, if some other hw mechanism is provided for synchronizing between IP blocks, it could be supported as an alternate implementation with it's own fence ops in a similar way. enable_signaling callback is used to provide sw signaling in case a cpu waiter is requested or no compatible hardware signaling could be used. The intention is to provide a userspace interface (presumably via eventfd) later, to be used in conjunction with dma-buf's mmap support for sw access to buffers (or for userspace apps that would prefer to do their own synchronization). v1: Original v2: After discussion w/ danvet and mlankhorst on #dri-devel, we decided that dma-fence didn't need to care about the sw->hw signaling path (it can be handled same as sw->sw case), and therefore the fence->ops can be simplified and more handled in the core. So remove the signal, add_callback, cancel_callback, and wait ops, and replace with a simple enable_signaling() op which can be used to inform a fence supporting hw->hw signaling that one or more devices which do not support hw signaling are waiting (and therefore it should enable an irq or do whatever is necessary in order that the CPU is notified when the fence is passed). v3: Fix locking fail in attach_fence() and get_fence() v4: Remove tie-in w/ dma-buf.. after discussion w/ danvet and mlankorst we decided that we need to be able to attach one fence to N dma-buf's, so using the list_head in dma-fence struct would be problematic. v5: [ Maarten Lankhorst ] Updated for dma-bikeshed-fence and dma-buf-manager. v6: [ Maarten Lankhorst ] I removed dma_fence_cancel_callback and some comments about checking if fence fired or not. This is broken by design. waitqueue_active during destruction is now fatal, since the signaller should be holding a reference in enable_signalling until it signalled the fence. Pass the original dma_fence_cb along, and call __remove_wait in the dma_fence_callback handler, so that no cleanup needs to be performed. v7: [ Maarten Lankhorst ] Set cb->func and only enable sw signaling if fence wasn't signaled yet, for example for hardware fences that may choose to signal blindly. v8: [ Maarten Lankhorst ] Tons of tiny fixes, moved __dma_fence_init to header and fixed include mess. dma-fence.h now includes dma-buf.h All members are now initialized, so kmalloc can be used for allocating a dma-fence. More documentation added. v9: Change compiler bitfields to flags, change return type of enable_signaling to bool. Rework dma_fence_wait. Added dma_fence_is_signaled and dma_fence_wait_timeout. s/dma// and change exports to non GPL. Added fence_is_signaled and fence_enable_sw_signaling calls, add ability to override default wait operation. v10: remove event_queue, use a custom list, export try_to_wake_up from scheduler. Remove fence lock and use a global spinlock instead, this should hopefully remove all the locking headaches I was having on trying to implement this. enable_signaling is called with this lock held. v11: Use atomic ops for flags, lifting the need for some spin_lock_irqsaves. However I kept the guarantee that after fence_signal returns, it is guaranteed that enable_signaling has either been called to completion, or will not be called any more. Add contexts and seqno to base fence implementation. This allows you to wait for less fences, by testing for seqno + signaled, and then only wait on the later fence. Add FENCE_TRACE, FENCE_WARN, and FENCE_ERR. This makes debugging easier. An CONFIG_DEBUG_FENCE will be added to turn off the FENCE_TRACE spam, and another runtime option can turn it off at runtime. v12: Add CONFIG_FENCE_TRACE. Add missing documentation for the fence->context and fence->seqno members. Signed-off-by: Maarten Lankhorst <maarten.lankhorst(a)canonical.com> --- Documentation/DocBook/device-drivers.tmpl | 2 drivers/base/Kconfig | 10 + drivers/base/Makefile | 2 drivers/base/fence.c | 286 +++++++++++++++++++++++ include/linux/fence.h | 365 +++++++++++++++++++++++++++++ 5 files changed, 664 insertions(+), 1 deletion(-) create mode 100644 drivers/base/fence.c create mode 100644 include/linux/fence.h diff --git a/Documentation/DocBook/device-drivers.tmpl b/Documentation/DocBook/device-drivers.tmpl index cbfdf54..241f4c5 100644 --- a/Documentation/DocBook/device-drivers.tmpl +++ b/Documentation/DocBook/device-drivers.tmpl @@ -126,6 +126,8 @@ X!Edrivers/base/interface.c </sect1> <sect1><title>Device Drivers DMA Management</title> !Edrivers/base/dma-buf.c +!Edrivers/base/fence.c +!Iinclude/linux/fence.h !Edrivers/base/reservation.c !Iinclude/linux/reservation.h !Edrivers/base/dma-coherent.c diff --git a/drivers/base/Kconfig b/drivers/base/Kconfig index 5daa259..0ad35df 100644 --- a/drivers/base/Kconfig +++ b/drivers/base/Kconfig @@ -200,6 +200,16 @@ config DMA_SHARED_BUFFER APIs extension; the file's descriptor can then be passed on to other driver. +config FENCE_TRACE + bool "Enable verbose FENCE_TRACE messages" + default n + depends on DMA_SHARED_BUFFER + help + Enable the FENCE_TRACE printks. This will add extra + spam to the config log, but will make it easier to diagnose + lockup related problems for dma-buffers shared across multiple + devices. + config CMA bool "Contiguous Memory Allocator" depends on HAVE_DMA_CONTIGUOUS && HAVE_MEMBLOCK diff --git a/drivers/base/Makefile b/drivers/base/Makefile index 48029aa..8a55cb9 100644 --- a/drivers/base/Makefile +++ b/drivers/base/Makefile @@ -10,7 +10,7 @@ obj-$(CONFIG_CMA) += dma-contiguous.o obj-y += power/ obj-$(CONFIG_HAS_DMA) += dma-mapping.o obj-$(CONFIG_HAVE_GENERIC_DMA_COHERENT) += dma-coherent.o -obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf.o reservation.o +obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf.o fence.o reservation.o obj-$(CONFIG_ISA) += isa.o obj-$(CONFIG_FW_LOADER) += firmware_class.o obj-$(CONFIG_NUMA) += node.o diff --git a/drivers/base/fence.c b/drivers/base/fence.c new file mode 100644 index 0000000..28e5ffd --- /dev/null +++ b/drivers/base/fence.c @@ -0,0 +1,286 @@ +/* + * Fence mechanism for dma-buf and to allow for asynchronous dma access + * + * Copyright (C) 2012 Canonical Ltd + * Copyright (C) 2012 Texas Instruments + * + * Authors: + * Rob Clark <rob.clark(a)linaro.org> + * Maarten Lankhorst <maarten.lankhorst(a)canonical.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/slab.h> +#include <linux/export.h> +#include <linux/fence.h> + +atomic_t fence_context_counter = ATOMIC_INIT(0); +EXPORT_SYMBOL(fence_context_counter); + +int __fence_signal(struct fence *fence) +{ + struct fence_cb *cur, *tmp; + int ret = 0; + + if (WARN_ON(!fence)) + return -EINVAL; + + if (test_and_set_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) { + ret = -EINVAL; + + /* + * we might have raced with the unlocked fence_signal, + * still run through all callbacks + */ + } + + list_for_each_entry_safe(cur, tmp, &fence->cb_list, node) { + list_del_init(&cur->node); + cur->func(fence, cur, cur->priv); + } + return ret; +} +EXPORT_SYMBOL(__fence_signal); + +/** + * fence_signal - signal completion of a fence + * @fence: the fence to signal + * + * Signal completion for software callbacks on a fence, this will unblock + * fence_wait() calls and run all the callbacks added with + * fence_add_callback(). Can be called multiple times, but since a fence + * can only go from unsignaled to signaled state, it will only be effective + * the first time. + */ +int fence_signal(struct fence *fence) +{ + unsigned long flags; + + if (!fence || test_and_set_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return -EINVAL; + + if (test_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags)) { + struct fence_cb *cur, *tmp; + + spin_lock_irqsave(fence->lock, flags); + list_for_each_entry_safe(cur, tmp, &fence->cb_list, node) { + list_del_init(&cur->node); + cur->func(fence, cur, cur->priv); + } + spin_unlock_irqrestore(fence->lock, flags); + } + return 0; +} +EXPORT_SYMBOL(fence_signal); + +void release_fence(struct kref *kref) +{ + struct fence *fence = + container_of(kref, struct fence, refcount); + + BUG_ON(!list_empty(&fence->cb_list)); + + if (fence->ops->release) + fence->ops->release(fence); + else + kfree(fence); +} +EXPORT_SYMBOL(release_fence); + +/** + * fence_enable_sw_signaling - enable signaling on fence + * @fence: [in] the fence to enable + * + * this will request for sw signaling to be enabled, to make the fence + * complete as soon as possible + */ +void fence_enable_sw_signaling(struct fence *fence) +{ + unsigned long flags; + + if (!test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags) && + !test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) { + spin_lock_irqsave(fence->lock, flags); + + if (!fence->ops->enable_signaling(fence)) + __fence_signal(fence); + + spin_unlock_irqrestore(fence->lock, flags); + } +} +EXPORT_SYMBOL(fence_enable_sw_signaling); + +/** + * fence_add_callback - add a callback to be called when the fence + * is signaled + * @fence: [in] the fence to wait on + * @cb: [in] the callback to register + * @func: [in] the function to call + * @priv: [in] the argument to pass to function + * + * cb will be initialized by fence_add_callback, no initialization + * by the caller is required. Any number of callbacks can be registered + * to a fence, but a callback can only be registered to one fence at a time. + * + * Note that the callback can be called from an atomic context. If + * fence is already signaled, this function will return -ENOENT (and + * *not* call the callback) + * + * Add a software callback to the fence. Same restrictions apply to + * refcount as it does to fence_wait, however the caller doesn't need to + * keep a refcount to fence afterwards: when software access is enabled, + * the creator of the fence is required to keep the fence alive until + * after it signals with fence_signal. The callback itself can be called + * from irq context. + * + */ +int fence_add_callback(struct fence *fence, struct fence_cb *cb, + fence_func_t func, void *priv) +{ + unsigned long flags; + int ret = 0; + bool was_set; + + if (WARN_ON(!fence || !func)) + return -EINVAL; + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return -ENOENT; + + spin_lock_irqsave(fence->lock, flags); + + was_set = test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags); + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + ret = -ENOENT; + else if (!was_set && !fence->ops->enable_signaling(fence)) { + __fence_signal(fence); + ret = -ENOENT; + } + + if (!ret) { + cb->func = func; + cb->priv = priv; + list_add_tail(&cb->node, &fence->cb_list); + } + spin_unlock_irqrestore(fence->lock, flags); + + return ret; +} +EXPORT_SYMBOL(fence_add_callback); + +/** + * fence_remove_callback - remove a callback from the signaling list + * @fence: [in] the fence to wait on + * @cb: [in] the callback to remove + * + * Remove a previously queued callback from the fence. This function returns + * true is the callback is succesfully removed, or false if the fence has + * already been signaled. + * + * *WARNING*: + * Cancelling a callback should only be done if you really know what you're + * doing, since deadlocks and race conditions could occur all too easily. For + * this reason, it should only ever be done on hardware lockup recovery, + * with a reference held to the fence. + */ +bool +fence_remove_callback(struct fence *fence, struct fence_cb *cb) +{ + unsigned long flags; + bool ret; + + spin_lock_irqsave(fence->lock, flags); + + ret = !list_empty(&cb->node); + if (ret) + list_del_init(&cb->node); + + spin_unlock_irqrestore(fence->lock, flags); + + return ret; +} +EXPORT_SYMBOL(fence_remove_callback); + +static void +fence_default_wait_cb(struct fence *fence, struct fence_cb *cb, void *priv) +{ + try_to_wake_up(priv, TASK_NORMAL, 0); +} + +/** + * fence_default_wait - default sleep until the fence gets signaled + * or until timeout elapses + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * @timeout: [in] timeout value in jiffies, or MAX_SCHEDULE_TIMEOUT + * + * Returns -ERESTARTSYS if interrupted, 0 if the wait timed out, or the + * remaining timeout in jiffies on success. + */ +long +fence_default_wait(struct fence *fence, bool intr, signed long timeout) +{ + struct fence_cb cb; + unsigned long flags; + long ret = timeout; + bool was_set; + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return timeout; + + spin_lock_irqsave(fence->lock, flags); + + if (intr && signal_pending(current)) { + ret = -ERESTARTSYS; + goto out; + } + + was_set = test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags); + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + goto out; + + if (!was_set && !fence->ops->enable_signaling(fence)) { + __fence_signal(fence); + goto out; + } + + cb.func = fence_default_wait_cb; + cb.priv = current; + list_add(&cb.node, &fence->cb_list); + + while (!test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags) && ret > 0) { + if (intr) + __set_current_state(TASK_INTERRUPTIBLE); + else + __set_current_state(TASK_UNINTERRUPTIBLE); + spin_unlock_irqrestore(fence->lock, flags); + + ret = schedule_timeout(ret); + + spin_lock_irqsave(fence->lock, flags); + if (ret > 0 && intr && signal_pending(current)) + ret = -ERESTARTSYS; + } + + if (!list_empty(&cb.node)) + list_del(&cb.node); + __set_current_state(TASK_RUNNING); + +out: + spin_unlock_irqrestore(fence->lock, flags); + return ret; +} +EXPORT_SYMBOL(fence_default_wait); diff --git a/include/linux/fence.h b/include/linux/fence.h new file mode 100644 index 0000000..8c7a126 --- /dev/null +++ b/include/linux/fence.h @@ -0,0 +1,365 @@ +/* + * Fence mechanism for dma-buf to allow for asynchronous dma access + * + * Copyright (C) 2012 Canonical Ltd + * Copyright (C) 2012 Texas Instruments + * + * Authors: + * Rob Clark <rob.clark(a)linaro.org> + * Maarten Lankhorst <maarten.lankhorst(a)canonical.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef __LINUX_FENCE_H +#define __LINUX_FENCE_H + +#include <linux/err.h> +#include <linux/wait.h> +#include <linux/list.h> +#include <linux/bitops.h> +#include <linux/kref.h> +#include <linux/sched.h> +#include <linux/printk.h> + +struct fence; +struct fence_ops; +struct fence_cb; + +/** + * struct fence - software synchronization primitive + * @refcount: refcount for this fence + * @ops: fence_ops associated with this fence + * @cb_list: list of all callbacks to call + * @lock: spin_lock_irqsave used for locking + * @context: execution context this fence belongs to, returned by + * fence_context_alloc() + * @seqno: the sequence number of this fence inside the execution context, + * can be compared to decide which fence would be signaled later. + * @flags: A mask of FENCE_FLAG_* defined below + * + * the flags member must be manipulated and read using the appropriate + * atomic ops (bit_*), so taking the spinlock will not be needed most + * of the time. + * + * FENCE_FLAG_SIGNALED_BIT - fence is already signaled + * FENCE_FLAG_ENABLE_SIGNAL_BIT - enable_signaling might have been called* + * FENCE_FLAG_USER_BITS - start of the unused bits, can be used by the + * implementer of the fence for its own purposes. Can be used in different + * ways by different fence implementers, so do not rely on this. + * + * *) Since atomic bitops are used, this is not guaranteed to be the case. + * Particularly, if the bit was set, but fence_signal was called right + * before this bit was set, it would have been able to set the + * FENCE_FLAG_SIGNALED_BIT, before enable_signaling was called. + * Adding a check for FENCE_FLAG_SIGNALED_BIT after setting + * FENCE_FLAG_ENABLE_SIGNAL_BIT closes this race, and makes sure that + * after fence_signal was called, any enable_signaling call will have either + * been completed, or never called at all. + */ +struct fence { + struct kref refcount; + const struct fence_ops *ops; + struct list_head cb_list; + spinlock_t *lock; + unsigned context, seqno; + unsigned long flags; +}; + +enum fence_flag_bits { + FENCE_FLAG_SIGNALED_BIT, + FENCE_FLAG_ENABLE_SIGNAL_BIT, + FENCE_FLAG_USER_BITS, /* must always be last member */ +}; + +typedef void (*fence_func_t)(struct fence *fence, struct fence_cb *cb, void *priv); + +/** + * struct fence_cb - callback for fence_add_callback + * @node: used by fence_add_callback to append this struct to fence::cb_list + * @func: fence_func_t to call + * @priv: value of priv to pass to function + * + * This struct will be initialized by fence_add_callback, additional + * data can be passed along by embedding fence_cb in another struct. + */ +struct fence_cb { + struct list_head node; + fence_func_t func; + void *priv; +}; + +/** + * struct fence_ops - operations implemented for fence + * @enable_signaling: enable software signaling of fence + * @signaled: [optional] peek whether the fence is signaled, can be null + * @wait: custom wait implementation + * @release: [optional] called on destruction of fence, can be null + * + * Notes on enable_signaling: + * For fence implementations that have the capability for hw->hw + * signaling, they can implement this op to enable the necessary + * irqs, or insert commands into cmdstream, etc. This is called + * in the first wait() or add_callback() path to let the fence + * implementation know that there is another driver waiting on + * the signal (ie. hw->sw case). + * + * This function can be called called from atomic context, but not + * from irq context, so normal spinlocks can be used. + * + * A return value of false indicates the fence already passed, + * or some failure occured that made it impossible to enable + * signaling. True indicates succesful enabling. + * + * Calling fence_signal before enable_signaling is called allows + * for a tiny race window in which enable_signaling is called during, + * before, or after fence_signal. To fight this, it is recommended + * that before enable_signaling returns true an extra reference is + * taken on the fence, to be released when the fence is signaled. + * This will mean fence_signal will still be called twice, but + * the second time will be a noop since it was already signaled. + * + * Notes on wait: + * Must not be NULL, set to fence_default_wait for default implementation. + * the fence_default_wait implementation should work for any fence, as long + * as enable_signaling works correctly. + * + * Must return -ERESTARTSYS if the wait is intr = true and the wait was + * interrupted, and remaining jiffies if fence has signaled, or 0 if wait + * timed out. Can also return other error values on custom implementations, + * which should be treated as if the fence is signaled. For example a hardware + * lockup could be reported like that. + * + * Notes on release: + * Can be NULL, this function allows additional commands to run on + * destruction of the fence. Can be called from irq context. + * If pointer is set to NULL, kfree will get called instead. + */ + +struct fence_ops { + bool (*enable_signaling)(struct fence *fence); + bool (*signaled)(struct fence *fence); + long (*wait)(struct fence *fence, bool intr, signed long timeout); + void (*release)(struct fence *fence); +}; + +/** + * __fence_init - Initialize a custom fence. + * @fence: [in] the fence to initialize + * @ops: [in] the fence_ops for operations on this fence + * @lock: [in] the irqsafe spinlock to use for locking this fence + * @context: [in] the execution context this fence is run on + * @seqno: [in] a linear increasing sequence number for this context + * + * Initializes an allocated fence, the caller doesn't have to keep its + * refcount after committing with this fence, but it will need to hold a + * refcount again if fence_ops.enable_signaling gets called. This can + * be used for other implementing other types of fence. + * + * context and seqno are used for easy comparison between fences, allowing + * to check which fence is later by simply using fence_later. + */ +static inline void +__fence_init(struct fence *fence, const struct fence_ops *ops, + spinlock_t *lock, unsigned context, unsigned seqno) +{ + BUG_ON(!ops || !lock || !ops->enable_signaling || !ops->wait); + + kref_init(&fence->refcount); + fence->ops = ops; + INIT_LIST_HEAD(&fence->cb_list); + fence->lock = lock; + fence->context = context; + fence->seqno = seqno; + fence->flags = 0UL; +} + +/** + * fence_get - increases refcount of the fence + * @fence: [in] fence to increase refcount of + */ +static inline void fence_get(struct fence *fence) +{ + if (WARN_ON(!fence)) + return; + kref_get(&fence->refcount); +} + +extern void release_fence(struct kref *kref); + +/** + * fence_put - decreases refcount of the fence + * @fence: [in] fence to reduce refcount of + */ +static inline void fence_put(struct fence *fence) +{ + if (WARN_ON(!fence)) + return; + kref_put(&fence->refcount, release_fence); +} + +int fence_signal(struct fence *fence); +int __fence_signal(struct fence *fence); +long fence_default_wait(struct fence *fence, bool intr, signed long timeout); +int fence_add_callback(struct fence *fence, struct fence_cb *cb, + fence_func_t func, void *priv); +bool fence_remove_callback(struct fence *fence, struct fence_cb *cb); +void fence_enable_sw_signaling(struct fence *fence); + +/** + * fence_is_signaled - Return an indication if the fence is signaled yet. + * @fence: [in] the fence to check + * + * Returns true if the fence was already signaled, false if not. Since this + * function doesn't enable signaling, it is not guaranteed to ever return true + * If fence_add_callback, fence_wait or fence_enable_sw_signaling + * haven't been called before. + * + * It's recommended for seqno fences to call fence_signal when the + * operation is complete, it makes it possible to prevent issues from + * wraparound between time of issue and time of use by checking the return + * value of this function before calling hardware-specific wait instructions. + */ +static inline bool +fence_is_signaled(struct fence *fence) +{ + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return true; + + if (fence->ops->signaled && fence->ops->signaled(fence)) { + fence_signal(fence); + return true; + } + + return false; +} + +/** + * fence_later - return the chronologically later fence + * @f1: [in] the first fence from the same context + * @f2: [in] the second fence from the same context + * + * Returns NULL if both fences are signaled, otherwise the fence that would be + * signaled last. Both fences must be from the same context, since a seqno is + * not re-used across contexts. + */ +static inline struct fence *fence_later(struct fence *f1, struct fence *f2) +{ + bool sig1, sig2; + + /* + * can't check just FENCE_FLAG_SIGNALED_BIT here, it may never have been + * set called if enable_signaling wasn't, and enabling that here is + * overkill. + */ + sig1 = fence_is_signaled(f1); + sig2 = fence_is_signaled(f2); + + if (sig1 && sig2) + return NULL; + + BUG_ON(f1->context != f2->context); + + if (sig1 || f2->seqno - f1->seqno <= INT_MAX) + return f2; + else + return f1; +} + +/** + * fence_wait_timeout - sleep until the fence gets signaled + * or until timeout elapses + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * @timeout: [in] timeout value in jiffies, or MAX_SCHEDULE_TIMEOUT + * + * Returns -ERESTARTSYS if interrupted, 0 if the wait timed out, or the + * remaining timeout in jiffies on success. Other error values may be + * returned on custom implementations. + * + * Performs a synchronous wait on this fence. It is assumed the caller + * directly or indirectly (buf-mgr between reservation and committing) + * holds a reference to the fence, otherwise the fence might be + * freed before return, resulting in undefined behavior. + */ +static inline long +fence_wait_timeout(struct fence *fence, bool intr, signed long timeout) +{ + if (WARN_ON(timeout < 0)) + return -EINVAL; + + return fence->ops->wait(fence, intr, timeout); +} + +/** + * fence_wait - sleep until the fence gets signaled + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * + * This function will return -ERESTARTSYS if interrupted by a signal, + * or 0 if the fence was signaled. Other error values may be + * returned on custom implementations. + * + * Performs a synchronous wait on this fence. It is assumed the caller + * directly or indirectly (buf-mgr between reservation and committing) + * holds a reference to the fence, otherwise the fence might be + * freed before return, resulting in undefined behavior. + */ +static inline long fence_wait(struct fence *fence, bool intr) +{ + long ret; + + /* Since fence_wait_timeout cannot timeout with + * MAX_SCHEDULE_TIMEOUT, only valid return values are + * -ERESTARTSYS and MAX_SCHEDULE_TIMEOUT. + */ + ret = fence_wait_timeout(fence, intr, MAX_SCHEDULE_TIMEOUT); + + return ret < 0 ? ret : 0; +} + +/** + * fence context counter: each execution context should have its own + * fence context, this allows checking if fences belong to the same + * context or not. One device can have multiple separate contexts, + * and they're used if some engine can run independently of another. + */ +extern atomic_t fence_context_counter; + +static inline unsigned fence_context_alloc(unsigned num) +{ + BUG_ON(!num); + return atomic_add_return(num, &fence_context_counter) - num; +} + +#define FENCE_TRACE(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + if (config_enabled(CONFIG_FENCE_TRACE)) \ + pr_info("f %u#%u: " fmt, \ + __ff->context, __ff->seqno, ##args); \ + } while (0) + +#define FENCE_WARN(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + pr_warn("f %u#%u: " fmt, __ff->context, __ff->seqno, ##args); \ + } while (0) + +#define FENCE_ERR(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + pr_err("f %u#%u: " fmt, __ff->context, __ff->seqno, ##args); \ + } while (0) + +#endif /* __LINUX_FENCE_H */

11 years, 4 months

[PATCH] fence: dma-buf cross-device synchronization (v13)

by Maarten Lankhorst

A fence can be attached to a buffer which is being filled or consumed by hw, to allow userspace to pass the buffer without waiting to another device. For example, userspace can call page_flip ioctl to display the next frame of graphics after kicking the GPU but while the GPU is still rendering. The display device sharing the buffer with the GPU would attach a callback to get notified when the GPU's rendering-complete IRQ fires, to update the scan-out address of the display, without having to wake up userspace. A driver must allocate a fence context for each execution ring that can run in parallel. The function for this takes an argument with how many contexts to allocate: + fence_context_alloc() A fence is transient, one-shot deal. It is allocated and attached to one or more dma-buf's. When the one that attached it is done, with the pending operation, it can signal the fence: + fence_signal() To have a rough approximation whether a fence is fired, call: + fence_is_signaled() The dma-buf-mgr handles tracking, and waiting on, the fences associated with a dma-buf. The one pending on the fence can add an async callback: + fence_add_callback() The callback can optionally be cancelled with: + fence_remove_callback() To wait synchronously, optionally with a timeout: + fence_wait() + fence_wait_timeout() A default software-only implementation is provided, which can be used by drivers attaching a fence to a buffer when they have no other means for hw sync. But a memory backed fence is also envisioned, because it is common that GPU's can write to, or poll on some memory location for synchronization. For example: fence = custom_get_fence(...); if ((seqno_fence = to_seqno_fence(fence)) != NULL) { dma_buf *fence_buf = fence->sync_buf; get_dma_buf(fence_buf); ... tell the hw the memory location to wait ... custom_wait_on(fence_buf, fence->seqno_ofs, fence->seqno); } else { /* fall-back to sw sync * / fence_add_callback(fence, my_cb); } On SoC platforms, if some other hw mechanism is provided for synchronizing between IP blocks, it could be supported as an alternate implementation with it's own fence ops in a similar way. enable_signaling callback is used to provide sw signaling in case a cpu waiter is requested or no compatible hardware signaling could be used. The intention is to provide a userspace interface (presumably via eventfd) later, to be used in conjunction with dma-buf's mmap support for sw access to buffers (or for userspace apps that would prefer to do their own synchronization). v1: Original v2: After discussion w/ danvet and mlankhorst on #dri-devel, we decided that dma-fence didn't need to care about the sw->hw signaling path (it can be handled same as sw->sw case), and therefore the fence->ops can be simplified and more handled in the core. So remove the signal, add_callback, cancel_callback, and wait ops, and replace with a simple enable_signaling() op which can be used to inform a fence supporting hw->hw signaling that one or more devices which do not support hw signaling are waiting (and therefore it should enable an irq or do whatever is necessary in order that the CPU is notified when the fence is passed). v3: Fix locking fail in attach_fence() and get_fence() v4: Remove tie-in w/ dma-buf.. after discussion w/ danvet and mlankorst we decided that we need to be able to attach one fence to N dma-buf's, so using the list_head in dma-fence struct would be problematic. v5: [ Maarten Lankhorst ] Updated for dma-bikeshed-fence and dma-buf-manager. v6: [ Maarten Lankhorst ] I removed dma_fence_cancel_callback and some comments about checking if fence fired or not. This is broken by design. waitqueue_active during destruction is now fatal, since the signaller should be holding a reference in enable_signalling until it signalled the fence. Pass the original dma_fence_cb along, and call __remove_wait in the dma_fence_callback handler, so that no cleanup needs to be performed. v7: [ Maarten Lankhorst ] Set cb->func and only enable sw signaling if fence wasn't signaled yet, for example for hardware fences that may choose to signal blindly. v8: [ Maarten Lankhorst ] Tons of tiny fixes, moved __dma_fence_init to header and fixed include mess. dma-fence.h now includes dma-buf.h All members are now initialized, so kmalloc can be used for allocating a dma-fence. More documentation added. v9: Change compiler bitfields to flags, change return type of enable_signaling to bool. Rework dma_fence_wait. Added dma_fence_is_signaled and dma_fence_wait_timeout. s/dma// and change exports to non GPL. Added fence_is_signaled and fence_enable_sw_signaling calls, add ability to override default wait operation. v10: remove event_queue, use a custom list, export try_to_wake_up from scheduler. Remove fence lock and use a global spinlock instead, this should hopefully remove all the locking headaches I was having on trying to implement this. enable_signaling is called with this lock held. v11: Use atomic ops for flags, lifting the need for some spin_lock_irqsaves. However I kept the guarantee that after fence_signal returns, it is guaranteed that enable_signaling has either been called to completion, or will not be called any more. Add contexts and seqno to base fence implementation. This allows you to wait for less fences, by testing for seqno + signaled, and then only wait on the later fence. Add FENCE_TRACE, FENCE_WARN, and FENCE_ERR. This makes debugging easier. An CONFIG_DEBUG_FENCE will be added to turn off the FENCE_TRACE spam, and another runtime option can turn it off at runtime. v12: Add CONFIG_FENCE_TRACE. Add missing documentation for the fence->context and fence->seqno members. v13: Fixup CONFIG_FENCE_TRACE kconfig description. Move fence_context_alloc to fence. Simplify fence_later. Kill priv member to fence_cb. Signed-off-by: Maarten Lankhorst <maarten.lankhorst(a)canonical.com> --- Documentation/DocBook/device-drivers.tmpl | 2 drivers/base/Kconfig | 10 + drivers/base/Makefile | 2 drivers/base/fence.c | 312 ++++++++++++++++++++++++++ include/linux/fence.h | 344 +++++++++++++++++++++++++++++ 5 files changed, 669 insertions(+), 1 deletion(-) create mode 100644 drivers/base/fence.c create mode 100644 include/linux/fence.h diff --git a/Documentation/DocBook/device-drivers.tmpl b/Documentation/DocBook/device-drivers.tmpl index fe397f9..95d0db9 100644 --- a/Documentation/DocBook/device-drivers.tmpl +++ b/Documentation/DocBook/device-drivers.tmpl @@ -126,6 +126,8 @@ X!Edrivers/base/interface.c </sect1> <sect1><title>Device Drivers DMA Management</title> !Edrivers/base/dma-buf.c +!Edrivers/base/fence.c +!Iinclude/linux/fence.h !Edrivers/base/reservation.c !Iinclude/linux/reservation.h !Edrivers/base/dma-coherent.c diff --git a/drivers/base/Kconfig b/drivers/base/Kconfig index 5daa259..2bf0add 100644 --- a/drivers/base/Kconfig +++ b/drivers/base/Kconfig @@ -200,6 +200,16 @@ config DMA_SHARED_BUFFER APIs extension; the file's descriptor can then be passed on to other driver. +config FENCE_TRACE + bool "Enable verbose FENCE_TRACE messages" + default n + depends on DMA_SHARED_BUFFER + help + Enable the FENCE_TRACE printks. This will add extra + spam to the console log, but will make it easier to diagnose + lockup related problems for dma-buffers shared across multiple + devices. + config CMA bool "Contiguous Memory Allocator" depends on HAVE_DMA_CONTIGUOUS && HAVE_MEMBLOCK diff --git a/drivers/base/Makefile b/drivers/base/Makefile index 48029aa..8a55cb9 100644 --- a/drivers/base/Makefile +++ b/drivers/base/Makefile @@ -10,7 +10,7 @@ obj-$(CONFIG_CMA) += dma-contiguous.o obj-y += power/ obj-$(CONFIG_HAS_DMA) += dma-mapping.o obj-$(CONFIG_HAVE_GENERIC_DMA_COHERENT) += dma-coherent.o -obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf.o reservation.o +obj-$(CONFIG_DMA_SHARED_BUFFER) += dma-buf.o fence.o reservation.o obj-$(CONFIG_ISA) += isa.o obj-$(CONFIG_FW_LOADER) += firmware_class.o obj-$(CONFIG_NUMA) += node.o diff --git a/drivers/base/fence.c b/drivers/base/fence.c new file mode 100644 index 0000000..a0b1357 --- /dev/null +++ b/drivers/base/fence.c @@ -0,0 +1,312 @@ +/* + * Fence mechanism for dma-buf and to allow for asynchronous dma access + * + * Copyright (C) 2012 Canonical Ltd + * Copyright (C) 2012 Texas Instruments + * + * Authors: + * Rob Clark <robdclark(a)gmail.com> + * Maarten Lankhorst <maarten.lankhorst(a)canonical.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <linux/slab.h> +#include <linux/export.h> +#include <linux/fence.h> + +/** + * fence context counter: each execution context should have its own + * fence context, this allows checking if fences belong to the same + * context or not. One device can have multiple separate contexts, + * and they're used if some engine can run independently of another. + */ +static atomic_t fence_context_counter = ATOMIC_INIT(0); + +/** + * fence_context_alloc - allocate an array of fence contexts + * @num: [in] amount of contexts to allocate + * + * This function will return the first index of the number of fences allocated. + * The fence context is used for setting fence->context to a unique number. + */ +unsigned fence_context_alloc(unsigned num) +{ + BUG_ON(!num); + return atomic_add_return(num, &fence_context_counter) - num; +} +EXPORT_SYMBOL(fence_context_alloc); + +int __fence_signal(struct fence *fence) +{ + struct fence_cb *cur, *tmp; + int ret = 0; + + if (WARN_ON(!fence)) + return -EINVAL; + + if (test_and_set_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) { + ret = -EINVAL; + + /* + * we might have raced with the unlocked fence_signal, + * still run through all callbacks + */ + } + + list_for_each_entry_safe(cur, tmp, &fence->cb_list, node) { + list_del_init(&cur->node); + cur->func(fence, cur); + } + return ret; +} +EXPORT_SYMBOL(__fence_signal); + +/** + * fence_signal - signal completion of a fence + * @fence: the fence to signal + * + * Signal completion for software callbacks on a fence, this will unblock + * fence_wait() calls and run all the callbacks added with + * fence_add_callback(). Can be called multiple times, but since a fence + * can only go from unsignaled to signaled state, it will only be effective + * the first time. + */ +int fence_signal(struct fence *fence) +{ + unsigned long flags; + + if (!fence || test_and_set_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return -EINVAL; + + if (test_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags)) { + struct fence_cb *cur, *tmp; + + spin_lock_irqsave(fence->lock, flags); + list_for_each_entry_safe(cur, tmp, &fence->cb_list, node) { + list_del_init(&cur->node); + cur->func(fence, cur); + } + spin_unlock_irqrestore(fence->lock, flags); + } + return 0; +} +EXPORT_SYMBOL(fence_signal); + +void release_fence(struct kref *kref) +{ + struct fence *fence = + container_of(kref, struct fence, refcount); + + BUG_ON(!list_empty(&fence->cb_list)); + + if (fence->ops->release) + fence->ops->release(fence); + else + kfree(fence); +} +EXPORT_SYMBOL(release_fence); + +/** + * fence_enable_sw_signaling - enable signaling on fence + * @fence: [in] the fence to enable + * + * this will request for sw signaling to be enabled, to make the fence + * complete as soon as possible + */ +void fence_enable_sw_signaling(struct fence *fence) +{ + unsigned long flags; + + if (!test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags) && + !test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) { + spin_lock_irqsave(fence->lock, flags); + + if (!fence->ops->enable_signaling(fence)) + __fence_signal(fence); + + spin_unlock_irqrestore(fence->lock, flags); + } +} +EXPORT_SYMBOL(fence_enable_sw_signaling); + +/** + * fence_add_callback - add a callback to be called when the fence + * is signaled + * @fence: [in] the fence to wait on + * @cb: [in] the callback to register + * @func: [in] the function to call + * @priv: [in] the argument to pass to function + * + * cb will be initialized by fence_add_callback, no initialization + * by the caller is required. Any number of callbacks can be registered + * to a fence, but a callback can only be registered to one fence at a time. + * + * Note that the callback can be called from an atomic context. If + * fence is already signaled, this function will return -ENOENT (and + * *not* call the callback) + * + * Add a software callback to the fence. Same restrictions apply to + * refcount as it does to fence_wait, however the caller doesn't need to + * keep a refcount to fence afterwards: when software access is enabled, + * the creator of the fence is required to keep the fence alive until + * after it signals with fence_signal. The callback itself can be called + * from irq context. + * + */ +int fence_add_callback(struct fence *fence, struct fence_cb *cb, + fence_func_t func, void *priv) +{ + unsigned long flags; + int ret = 0; + bool was_set; + + if (WARN_ON(!fence || !func)) + return -EINVAL; + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return -ENOENT; + + spin_lock_irqsave(fence->lock, flags); + + was_set = test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags); + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + ret = -ENOENT; + else if (!was_set && !fence->ops->enable_signaling(fence)) { + __fence_signal(fence); + ret = -ENOENT; + } + + if (!ret) { + cb->func = func; + list_add_tail(&cb->node, &fence->cb_list); + } + spin_unlock_irqrestore(fence->lock, flags); + + return ret; +} +EXPORT_SYMBOL(fence_add_callback); + +/** + * fence_remove_callback - remove a callback from the signaling list + * @fence: [in] the fence to wait on + * @cb: [in] the callback to remove + * + * Remove a previously queued callback from the fence. This function returns + * true is the callback is succesfully removed, or false if the fence has + * already been signaled. + * + * *WARNING*: + * Cancelling a callback should only be done if you really know what you're + * doing, since deadlocks and race conditions could occur all too easily. For + * this reason, it should only ever be done on hardware lockup recovery, + * with a reference held to the fence. + */ +bool +fence_remove_callback(struct fence *fence, struct fence_cb *cb) +{ + unsigned long flags; + bool ret; + + spin_lock_irqsave(fence->lock, flags); + + ret = !list_empty(&cb->node); + if (ret) + list_del_init(&cb->node); + + spin_unlock_irqrestore(fence->lock, flags); + + return ret; +} +EXPORT_SYMBOL(fence_remove_callback); + +struct default_wait_cb { + struct fence_cb base; + struct task_struct *task; +}; + +static void +fence_default_wait_cb(struct fence *fence, struct fence_cb *cb) +{ + struct default_wait_cb *wait = + container_of(cb, struct default_wait_cb, base); + + try_to_wake_up(wait->task, TASK_NORMAL, 0); +} + +/** + * fence_default_wait - default sleep until the fence gets signaled + * or until timeout elapses + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * @timeout: [in] timeout value in jiffies, or MAX_SCHEDULE_TIMEOUT + * + * Returns -ERESTARTSYS if interrupted, 0 if the wait timed out, or the + * remaining timeout in jiffies on success. + */ +long +fence_default_wait(struct fence *fence, bool intr, signed long timeout) +{ + struct default_wait_cb cb; + unsigned long flags; + long ret = timeout; + bool was_set; + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return timeout; + + spin_lock_irqsave(fence->lock, flags); + + if (intr && signal_pending(current)) { + ret = -ERESTARTSYS; + goto out; + } + + was_set = test_and_set_bit(FENCE_FLAG_ENABLE_SIGNAL_BIT, &fence->flags); + + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + goto out; + + if (!was_set && !fence->ops->enable_signaling(fence)) { + __fence_signal(fence); + goto out; + } + + cb.base.func = fence_default_wait_cb; + cb.task = current; + list_add(&cb.base.node, &fence->cb_list); + + while (!test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags) && ret > 0) { + if (intr) + __set_current_state(TASK_INTERRUPTIBLE); + else + __set_current_state(TASK_UNINTERRUPTIBLE); + spin_unlock_irqrestore(fence->lock, flags); + + ret = schedule_timeout(ret); + + spin_lock_irqsave(fence->lock, flags); + if (ret > 0 && intr && signal_pending(current)) + ret = -ERESTARTSYS; + } + + if (!list_empty(&cb.base.node)) + list_del(&cb.base.node); + __set_current_state(TASK_RUNNING); + +out: + spin_unlock_irqrestore(fence->lock, flags); + return ret; +} +EXPORT_SYMBOL(fence_default_wait); diff --git a/include/linux/fence.h b/include/linux/fence.h new file mode 100644 index 0000000..0319c59 --- /dev/null +++ b/include/linux/fence.h @@ -0,0 +1,344 @@ +/* + * Fence mechanism for dma-buf to allow for asynchronous dma access + * + * Copyright (C) 2012 Canonical Ltd + * Copyright (C) 2012 Texas Instruments + * + * Authors: + * Rob Clark <robdclark(a)gmail.com> + * Maarten Lankhorst <maarten.lankhorst(a)canonical.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published by + * the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef __LINUX_FENCE_H +#define __LINUX_FENCE_H + +#include <linux/err.h> +#include <linux/wait.h> +#include <linux/list.h> +#include <linux/bitops.h> +#include <linux/kref.h> +#include <linux/sched.h> +#include <linux/printk.h> + +struct fence; +struct fence_ops; +struct fence_cb; + +/** + * struct fence - software synchronization primitive + * @refcount: refcount for this fence + * @ops: fence_ops associated with this fence + * @cb_list: list of all callbacks to call + * @lock: spin_lock_irqsave used for locking + * @context: execution context this fence belongs to, returned by + * fence_context_alloc() + * @seqno: the sequence number of this fence inside the execution context, + * can be compared to decide which fence would be signaled later. + * @flags: A mask of FENCE_FLAG_* defined below + * + * the flags member must be manipulated and read using the appropriate + * atomic ops (bit_*), so taking the spinlock will not be needed most + * of the time. + * + * FENCE_FLAG_SIGNALED_BIT - fence is already signaled + * FENCE_FLAG_ENABLE_SIGNAL_BIT - enable_signaling might have been called* + * FENCE_FLAG_USER_BITS - start of the unused bits, can be used by the + * implementer of the fence for its own purposes. Can be used in different + * ways by different fence implementers, so do not rely on this. + * + * *) Since atomic bitops are used, this is not guaranteed to be the case. + * Particularly, if the bit was set, but fence_signal was called right + * before this bit was set, it would have been able to set the + * FENCE_FLAG_SIGNALED_BIT, before enable_signaling was called. + * Adding a check for FENCE_FLAG_SIGNALED_BIT after setting + * FENCE_FLAG_ENABLE_SIGNAL_BIT closes this race, and makes sure that + * after fence_signal was called, any enable_signaling call will have either + * been completed, or never called at all. + */ +struct fence { + struct kref refcount; + const struct fence_ops *ops; + struct list_head cb_list; + spinlock_t *lock; + unsigned context, seqno; + unsigned long flags; +}; + +enum fence_flag_bits { + FENCE_FLAG_SIGNALED_BIT, + FENCE_FLAG_ENABLE_SIGNAL_BIT, + FENCE_FLAG_USER_BITS, /* must always be last member */ +}; + +typedef void (*fence_func_t)(struct fence *fence, struct fence_cb *cb); + +/** + * struct fence_cb - callback for fence_add_callback + * @node: used by fence_add_callback to append this struct to fence::cb_list + * @func: fence_func_t to call + * @priv: value of priv to pass to function + * + * This struct will be initialized by fence_add_callback, additional + * data can be passed along by embedding fence_cb in another struct. + */ +struct fence_cb { + struct list_head node; + fence_func_t func; +}; + +/** + * struct fence_ops - operations implemented for fence + * @enable_signaling: enable software signaling of fence + * @signaled: [optional] peek whether the fence is signaled, can be null + * @wait: custom wait implementation + * @release: [optional] called on destruction of fence, can be null + * + * Notes on enable_signaling: + * For fence implementations that have the capability for hw->hw + * signaling, they can implement this op to enable the necessary + * irqs, or insert commands into cmdstream, etc. This is called + * in the first wait() or add_callback() path to let the fence + * implementation know that there is another driver waiting on + * the signal (ie. hw->sw case). + * + * This function can be called called from atomic context, but not + * from irq context, so normal spinlocks can be used. + * + * A return value of false indicates the fence already passed, + * or some failure occured that made it impossible to enable + * signaling. True indicates succesful enabling. + * + * Calling fence_signal before enable_signaling is called allows + * for a tiny race window in which enable_signaling is called during, + * before, or after fence_signal. To fight this, it is recommended + * that before enable_signaling returns true an extra reference is + * taken on the fence, to be released when the fence is signaled. + * This will mean fence_signal will still be called twice, but + * the second time will be a noop since it was already signaled. + * + * Notes on wait: + * Must not be NULL, set to fence_default_wait for default implementation. + * the fence_default_wait implementation should work for any fence, as long + * as enable_signaling works correctly. + * + * Must return -ERESTARTSYS if the wait is intr = true and the wait was + * interrupted, and remaining jiffies if fence has signaled, or 0 if wait + * timed out. Can also return other error values on custom implementations, + * which should be treated as if the fence is signaled. For example a hardware + * lockup could be reported like that. + * + * Notes on release: + * Can be NULL, this function allows additional commands to run on + * destruction of the fence. Can be called from irq context. + * If pointer is set to NULL, kfree will get called instead. + */ + +struct fence_ops { + bool (*enable_signaling)(struct fence *fence); + bool (*signaled)(struct fence *fence); + long (*wait)(struct fence *fence, bool intr, signed long timeout); + void (*release)(struct fence *fence); +}; + +/** + * __fence_init - Initialize a custom fence. + * @fence: [in] the fence to initialize + * @ops: [in] the fence_ops for operations on this fence + * @lock: [in] the irqsafe spinlock to use for locking this fence + * @context: [in] the execution context this fence is run on + * @seqno: [in] a linear increasing sequence number for this context + * + * Initializes an allocated fence, the caller doesn't have to keep its + * refcount after committing with this fence, but it will need to hold a + * refcount again if fence_ops.enable_signaling gets called. This can + * be used for other implementing other types of fence. + * + * context and seqno are used for easy comparison between fences, allowing + * to check which fence is later by simply using fence_later. + */ +static inline void +__fence_init(struct fence *fence, const struct fence_ops *ops, + spinlock_t *lock, unsigned context, unsigned seqno) +{ + BUG_ON(!ops || !lock || !ops->enable_signaling || !ops->wait); + + kref_init(&fence->refcount); + fence->ops = ops; + INIT_LIST_HEAD(&fence->cb_list); + fence->lock = lock; + fence->context = context; + fence->seqno = seqno; + fence->flags = 0UL; +} + +/** + * fence_get - increases refcount of the fence + * @fence: [in] fence to increase refcount of + */ +static inline void fence_get(struct fence *fence) +{ + if (WARN_ON(!fence)) + return; + kref_get(&fence->refcount); +} + +extern void release_fence(struct kref *kref); + +/** + * fence_put - decreases refcount of the fence + * @fence: [in] fence to reduce refcount of + */ +static inline void fence_put(struct fence *fence) +{ + if (WARN_ON(!fence)) + return; + kref_put(&fence->refcount, release_fence); +} + +int fence_signal(struct fence *fence); +int __fence_signal(struct fence *fence); +long fence_default_wait(struct fence *fence, bool intr, signed long timeout); +int fence_add_callback(struct fence *fence, struct fence_cb *cb, + fence_func_t func, void *priv); +bool fence_remove_callback(struct fence *fence, struct fence_cb *cb); +void fence_enable_sw_signaling(struct fence *fence); + +/** + * fence_is_signaled - Return an indication if the fence is signaled yet. + * @fence: [in] the fence to check + * + * Returns true if the fence was already signaled, false if not. Since this + * function doesn't enable signaling, it is not guaranteed to ever return true + * If fence_add_callback, fence_wait or fence_enable_sw_signaling + * haven't been called before. + * + * It's recommended for seqno fences to call fence_signal when the + * operation is complete, it makes it possible to prevent issues from + * wraparound between time of issue and time of use by checking the return + * value of this function before calling hardware-specific wait instructions. + */ +static inline bool +fence_is_signaled(struct fence *fence) +{ + if (test_bit(FENCE_FLAG_SIGNALED_BIT, &fence->flags)) + return true; + + if (fence->ops->signaled && fence->ops->signaled(fence)) { + fence_signal(fence); + return true; + } + + return false; +} + +/** + * fence_later - return the chronologically later fence + * @f1: [in] the first fence from the same context + * @f2: [in] the second fence from the same context + * + * Returns NULL if both fences are signaled, otherwise the fence that would be + * signaled last. Both fences must be from the same context, since a seqno is + * not re-used across contexts. + */ +static inline struct fence *fence_later(struct fence *f1, struct fence *f2) +{ + BUG_ON(f1->context != f2->context); + + /* + * can't check just FENCE_FLAG_SIGNALED_BIT here, it may never have been + * set called if enable_signaling wasn't, and enabling that here is + * overkill. + */ + if (f2->seqno - f1->seqno <= INT_MAX) + return fence_is_signaled(f2) ? NULL : f2; + else + return fence_is_signaled(f1) ? NULL : f1; +} + +/** + * fence_wait_timeout - sleep until the fence gets signaled + * or until timeout elapses + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * @timeout: [in] timeout value in jiffies, or MAX_SCHEDULE_TIMEOUT + * + * Returns -ERESTARTSYS if interrupted, 0 if the wait timed out, or the + * remaining timeout in jiffies on success. Other error values may be + * returned on custom implementations. + * + * Performs a synchronous wait on this fence. It is assumed the caller + * directly or indirectly (buf-mgr between reservation and committing) + * holds a reference to the fence, otherwise the fence might be + * freed before return, resulting in undefined behavior. + */ +static inline long +fence_wait_timeout(struct fence *fence, bool intr, signed long timeout) +{ + if (WARN_ON(timeout < 0)) + return -EINVAL; + + return fence->ops->wait(fence, intr, timeout); +} + +/** + * fence_wait - sleep until the fence gets signaled + * @fence: [in] the fence to wait on + * @intr: [in] if true, do an interruptible wait + * + * This function will return -ERESTARTSYS if interrupted by a signal, + * or 0 if the fence was signaled. Other error values may be + * returned on custom implementations. + * + * Performs a synchronous wait on this fence. It is assumed the caller + * directly or indirectly (buf-mgr between reservation and committing) + * holds a reference to the fence, otherwise the fence might be + * freed before return, resulting in undefined behavior. + */ +static inline long fence_wait(struct fence *fence, bool intr) +{ + long ret; + + /* Since fence_wait_timeout cannot timeout with + * MAX_SCHEDULE_TIMEOUT, only valid return values are + * -ERESTARTSYS and MAX_SCHEDULE_TIMEOUT. + */ + ret = fence_wait_timeout(fence, intr, MAX_SCHEDULE_TIMEOUT); + + return ret < 0 ? ret : 0; +} + +unsigned fence_context_alloc(unsigned num); + +#define FENCE_TRACE(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + if (config_enabled(CONFIG_FENCE_TRACE)) \ + pr_info("f %u#%u: " fmt, \ + __ff->context, __ff->seqno, ##args); \ + } while (0) + +#define FENCE_WARN(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + pr_warn("f %u#%u: " fmt, __ff->context, __ff->seqno, ##args); \ + } while (0) + +#define FENCE_ERR(f, fmt, args...) \ + do { \ + struct fence *__ff = (f); \ + pr_err("f %u#%u: " fmt, __ff->context, __ff->seqno, ##args); \ + } while (0) + +#endif /* __LINUX_FENCE_H */

11 years, 4 months

[PATCH] dma-buf: Expose buffer size to userspace

by Christopher James Halse Rogers

Each dma-buf has an associated size and it's reasonable for userspace to want to know what it is. Since userspace already has an fd, expose the size using the size = lseek(fd, SEEK_END, 0); lseek(fd, SEEK_CUR, 0); idiom. Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers(a)canonical.com> --- I've run into a point in the radeon DRM userspace where I need the size of a dma-buf. I could add a radeon-specific mechanism to get that, but this seems like something that would be more generally useful. I'm not entirely sure about supporting both SEEK_END and SEEK_CUR; this is somewhat of an abuse of lseek, as seeking obviously doesn't make sense. It's the obivous idiom for getting the size of what's on the other end of a file descriptor, though. I didn't notice anywhere to document this; Documentation/dma-buf-api didn't seem like the right place. Is there somewhere I've overlooked? drivers/base/dma-buf.c | 28 ++++++++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/drivers/base/dma-buf.c b/drivers/base/dma-buf.c index 6687ba7..c33a857 100644 --- a/drivers/base/dma-buf.c +++ b/drivers/base/dma-buf.c @@ -77,9 +77,36 @@ static int dma_buf_mmap_internal(struct file *file, struct vm_area_struct *vma) return dmabuf->ops->mmap(dmabuf, vma); } +static loff_t dma_buf_llseek(struct file *file, loff_t offset, int whence) +{ + struct dma_buf *dmabuf; + loff_t base; + + if (!is_dma_buf_file(file)) + return -EBADF; + + dmabuf = file->private_data; + + /* only support discovering the end of the buffer, + but also allow SEEK_SET to maintain the idiomatic + SEEK_END(0), SEEK_CUR(0) pattern */ + if (whence == SEEK_END) + base = dmabuf->size; + else if (whence == SEEK_SET) + base = 0; + else + return -EINVAL; + + if (offset != 0) + return -EINVAL; + + return base + offset; +} + static const struct file_operations dma_buf_fops = { .release = dma_buf_release, .mmap = dma_buf_mmap_internal, + .llseek = dma_buf_llseek, }; /* @@ -133,6 +160,7 @@ struct dma_buf *dma_buf_export_named(void *priv, const struct dma_buf_ops *ops, dmabuf->exp_name = exp_name; file = anon_inode_getfile("dmabuf", &dma_buf_fops, dmabuf, flags); + file->f_mode |= FMODE_LSEEK; dmabuf->file = file; -- 1.8.3.2

11 years, 4 months

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

Linaro-mm-sig August 2013