linaro-dev October 2011

linaro-dev@lists.linaro.org

107 participants
156 discussions

by Vincent Guittot

Hi, I've tried to use Linaro 11.08 nano image with vexpress 11.08 hwpack but the board hangs in the init script and I never get the shell prompt. if I use the linaro 11.07 nano image with the 11.08 hwpack, the vexpress board boot successfully. Did someone else face the same problem ? Regards, Vincent

13 years, 10 months

LTTng 2.0 pre-release for ARM

by Avik Sil

Hi, I've put together LTTng 2.0 tools into overlay PPA to use and evaluate it on ARM platforms. LTTng 2.0 [1] is a tracer toolchain that allows integrated kernel and user-space tracing from a single user interface: the "lttng" command. LTTng 2.0 kernel tracer modules build against a vanilla or distribution kernel, without need for additional patches. It is currently in pre-release state to gather feedback from users. I've taken the packages from LTTng Daily Builds PPA [2], modified it to build and run on armel and pushed it to overlay. To install it: $ sudo apt-add-repository ppa:linaro-maintainers/overlay $ sudo apt-get update $ sudo apt-get install lttng-tools lttng-modules-dkms babeltrace To run it, we need to create a session $ sudo lttng create mysession To list the available kernel events: $ sudo lttng list -k Enable all/some events for this session $ sudo lttng enable-event -a -k Start the tracing: $ sudo lttng start By default traces are saved in ~/lttng-traces/mysession-<date>-<time>/ When you're done: $ sudo lttng stop You can then read the trace with babeltrace: $ babeltrace /path/to/trace/dir Please test it and give feedback. Regards, Avik [1] http://lttng.org/lttng2.0 [2] https://launchpad.net/~lttng/+archive/daily

13 years, 10 months

[PATCH v10] pinctrl: add a driver for the U300 pinmux

by Linus Walleij

From: Linus Walleij <linus.walleij(a)linaro.org> This adds a driver for the U300 pinmux portions of the system controller "SYSCON". It also serves as an example of how to use the pinmux subsystem. This driver also houses the platform data for the only supported platform. This deletes the old U300 driver in arch/arm/mach-u300 and replace it with a driver using the new subsystem. The new driver is considerably fatter than the old one, but it also registers all 467 pins of the system and adds the power and EMIF pin groups and corresponding functions. The idea is to use this driver as a a reference for other implementation so it needs to be as complete and verbose as possible. Signed-off-by: Linus Walleij <linus.walleij(a)linaro.org> --- ChangeLog v9 -> v10 - Removed debug register dump (review from Barry Song) - Allocate sizeof(*ptr) instead of sizeof(struct foo) --- arch/arm/mach-u300/Kconfig | 2 + arch/arm/mach-u300/Makefile | 2 +- arch/arm/mach-u300/core.c | 84 +++- arch/arm/mach-u300/include/mach/syscon.h | 136 ---- arch/arm/mach-u300/mmc.c | 16 - arch/arm/mach-u300/padmux.c | 367 ---------- arch/arm/mach-u300/padmux.h | 39 - arch/arm/mach-u300/spi.c | 20 - drivers/pinctrl/Kconfig | 7 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinmux-u300.c | 1135 ++++++++++++++++++++++++++++++ 11 files changed, 1228 insertions(+), 581 deletions(-) delete mode 100644 arch/arm/mach-u300/padmux.c delete mode 100644 arch/arm/mach-u300/padmux.h create mode 100644 drivers/pinctrl/pinmux-u300.c diff --git a/arch/arm/mach-u300/Kconfig b/arch/arm/mach-u300/Kconfig index 32a7b0f..449fd6a 100644 --- a/arch/arm/mach-u300/Kconfig +++ b/arch/arm/mach-u300/Kconfig @@ -6,6 +6,8 @@ comment "ST-Ericsson Mobile Platform Products" config MACH_U300 bool "U300" + select PINCTRL + select PINMUX_U300 comment "ST-Ericsson U300/U330/U335/U365 Feature Selections" diff --git a/arch/arm/mach-u300/Makefile b/arch/arm/mach-u300/Makefile index 8fd354a..2855381 100644 --- a/arch/arm/mach-u300/Makefile +++ b/arch/arm/mach-u300/Makefile @@ -2,7 +2,7 @@ # Makefile for the linux kernel, U300 machine. # -obj-y := core.o clock.o timer.o padmux.o +obj-y := core.o clock.o timer.o obj-m := obj-n := obj- := diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 399c89f..2f5929b 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -25,6 +25,8 @@ #include <linux/err.h> #include <linux/mtd/nand.h> #include <linux/mtd/fsmc.h> +#include <linux/pinctrl/machine.h> +#include <linux/pinctrl/pinmux.h> #include <asm/types.h> #include <asm/setup.h> @@ -1535,6 +1537,14 @@ static struct coh901318_platform coh901318_platform = { .max_channels = U300_DMA_CHANNELS, }; +static struct resource pinmux_resources[] = { + { + .start = U300_SYSCON_BASE, + .end = U300_SYSCON_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + static struct platform_device wdog_device = { .name = "coh901327_wdog", .id = -1, @@ -1630,6 +1640,72 @@ static struct platform_device dma_device = { }, }; +static struct platform_device pinmux_device = { + .name = "pinmux-u300", + .id = -1, + .num_resources = ARRAY_SIZE(pinmux_resources), + .resource = pinmux_resources, +}; + +/* Pinmux settings */ +static struct pinmux_map u300_pinmux_map[] = { + /* anonymous maps for chip power and EMIFs */ + PINMUX_MAP_PRIMARY_SYS_HOG("POWER", "power"), + PINMUX_MAP_PRIMARY_SYS_HOG("EMIF0", "emif0"), + PINMUX_MAP_PRIMARY_SYS_HOG("EMIF1", "emif1"), + /* per-device maps for MMC/SD, SPI and UART */ + PINMUX_MAP_PRIMARY("MMCSD", "mmc0", "mmci"), + PINMUX_MAP_PRIMARY("SPI", "spi0", "pl022"), + PINMUX_MAP_PRIMARY("UART0", "uart0", "uart0"), +}; + +struct u300_mux_hog { + const char *name; + struct device *dev; + struct pinmux *pmx; +}; + +static struct u300_mux_hog u300_mux_hogs[] = { + { + .name = "uart0", + .dev = &uart0_device.dev, + }, + { + .name = "spi0", + .dev = &pl022_device.dev, + }, + { + .name = "mmc0", + .dev = &mmcsd_device.dev, + }, +}; + +static int __init u300_pinmux_fetch(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(u300_mux_hogs); i++) { + struct pinmux *pmx; + int ret; + + pmx = pinmux_get(u300_mux_hogs[i].dev, NULL); + if (IS_ERR(pmx)) { + pr_err("u300: could not get pinmux hog %s\n", + u300_mux_hogs[i].name); + continue; + } + ret = pinmux_enable(pmx); + if (ret) { + pr_err("u300: could enable pinmux hog %s\n", + u300_mux_hogs[i].name); + continue; + } + u300_mux_hogs[i].pmx = pmx; + } + return 0; +} +subsys_initcall(u300_pinmux_fetch); + /* * Notice that AMBA devices are initialized before platform devices. * @@ -1643,10 +1719,10 @@ static struct platform_device *platform_devs[] __initdata = { &gpio_device, &nand_device, &wdog_device, - &ave_device + &ave_device, + &pinmux_device, }; - /* * Interrupts: the U300 platforms have two pl190 ARM PrimeCells connected * together so some interrupts are connected to the first one and some @@ -1828,6 +1904,10 @@ void __init u300_init_devices(void) u300_assign_physmem(); + /* Initialize pinmuxing */ + pinmux_register_mappings(u300_pinmux_map, + ARRAY_SIZE(u300_pinmux_map)); + /* Register subdevices on the I2C buses */ u300_i2c_register_board_devices(); diff --git a/arch/arm/mach-u300/include/mach/syscon.h b/arch/arm/mach-u300/include/mach/syscon.h index 7444f5c..6e84f07 100644 --- a/arch/arm/mach-u300/include/mach/syscon.h +++ b/arch/arm/mach-u300/include/mach/syscon.h @@ -234,91 +234,6 @@ #define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE (0x0004) #define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE (0x0002) #define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE (0x0001) -/* PAD MUX Control register 1 (LOW) 16bit (R/W) */ -#define U300_SYSCON_PMC1LR (0x007C) -#define U300_SYSCON_PMC1LR_MASK (0xFFFF) -#define U300_SYSCON_PMC1LR_CDI_MASK (0xC000) -#define U300_SYSCON_PMC1LR_CDI_CDI (0x0000) -#define U300_SYSCON_PMC1LR_CDI_EMIF (0x4000) -#ifdef CONFIG_MACH_U300_BS335 -#define U300_SYSCON_PMC1LR_CDI_CDI2 (0x8000) -#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO (0xC000) -#elif CONFIG_MACH_U300_BS365 -#define U300_SYSCON_PMC1LR_CDI_GPIO (0x8000) -#define U300_SYSCON_PMC1LR_CDI_WCDMA (0xC000) -#endif -#define U300_SYSCON_PMC1LR_PDI_MASK (0x3000) -#define U300_SYSCON_PMC1LR_PDI_PDI (0x0000) -#define U300_SYSCON_PMC1LR_PDI_EGG (0x1000) -#define U300_SYSCON_PMC1LR_PDI_WCDMA (0x3000) -#define U300_SYSCON_PMC1LR_MMCSD_MASK (0x0C00) -#define U300_SYSCON_PMC1LR_MMCSD_MMCSD (0x0000) -#define U300_SYSCON_PMC1LR_MMCSD_MSPRO (0x0400) -#define U300_SYSCON_PMC1LR_MMCSD_DSP (0x0800) -#define U300_SYSCON_PMC1LR_MMCSD_WCDMA (0x0C00) -#define U300_SYSCON_PMC1LR_ETM_MASK (0x0300) -#define U300_SYSCON_PMC1LR_ETM_ACC (0x0000) -#define U300_SYSCON_PMC1LR_ETM_APP (0x0100) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK (0x00C0) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF (0x0040) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM (0x0080) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB (0x00C0) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK (0x0030) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF (0x0010) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM (0x0020) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI (0x0030) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK (0x000C) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF (0x0004) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM (0x0008) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI (0x000C) -#define U300_SYSCON_PMC1LR_EMIF_1_MASK (0x0003) -#define U300_SYSCON_PMC1LR_EMIF_1_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 (0x0001) -#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1 (0x0002) -#define U300_SYSCON_PMC1LR_EMIF_1 (0x0003) -/* PAD MUX Control register 2 (HIGH) 16bit (R/W) */ -#define U300_SYSCON_PMC1HR (0x007E) -#define U300_SYSCON_PMC1HR_MASK (0xFFFF) -#define U300_SYSCON_PMC1HR_MISC_2_MASK (0xC000) -#define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_MISC_2_MSPRO (0x4000) -#define U300_SYSCON_PMC1HR_MISC_2_DSP (0x8000) -#define U300_SYSCON_PMC1HR_MISC_2_AAIF (0xC000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK (0x3000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF (0x1000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP (0x2000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF (0x3000) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK (0x0C00) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC (0x0400) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP (0x0800) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF (0x0C00) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK (0x0300) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI (0x0100) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF (0x0300) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK (0x00C0) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI (0x0040) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF (0x00C0) -#define U300_SYSCON_PMC1HR_APP_SPI_2_MASK (0x0030) -#define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_SPI_2_SPI (0x0010) -#define U300_SYSCON_PMC1HR_APP_SPI_2_DSP (0x0020) -#define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF (0x0030) -#define U300_SYSCON_PMC1HR_APP_UART0_2_MASK (0x000C) -#define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_UART0_2_UART0 (0x0004) -#define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS (0x0008) -#define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF (0x000C) -#define U300_SYSCON_PMC1HR_APP_UART0_1_MASK (0x0003) -#define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_UART0_1_UART0 (0x0001) -#define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF (0x0003) /* Step one for killing the applications system 16bit (-/W) */ #define U300_SYSCON_KA1R (0x0080) #define U300_SYSCON_KA1R_MASK (0xFFFF) @@ -357,57 +272,6 @@ #define U300_SYSCON_PUCR_EMIF_1_16BIT_PU_ENABLE (0x0080) #define U300_SYSCON_PUCR_EMIF_1_8BIT_PU_ENABLE (0x0040) #define U300_SYSCON_PUCR_KEY_IN_PU_EN_MASK (0x003F) -/* Padmux 2 control */ -#define U300_SYSCON_PMC2R (0x100) -#define U300_SYSCON_PMC2R_APP_MISC_0_MASK (0x00C0) -#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM (0x0040) -#define U300_SYSCON_PMC2R_APP_MISC_0_MMC (0x0080) -#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 (0x00C0) -#define U300_SYSCON_PMC2R_APP_MISC_1_MASK (0x0300) -#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM (0x0100) -#define U300_SYSCON_PMC2R_APP_MISC_1_MMC (0x0200) -#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 (0x0300) -#define U300_SYSCON_PMC2R_APP_MISC_2_MASK (0x0C00) -#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM (0x0400) -#define U300_SYSCON_PMC2R_APP_MISC_2_MMC (0x0800) -#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 (0x0C00) -#define U300_SYSCON_PMC2R_APP_MISC_3_MASK (0x3000) -#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM (0x1000) -#define U300_SYSCON_PMC2R_APP_MISC_3_MMC (0x2000) -#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 (0x3000) -#define U300_SYSCON_PMC2R_APP_MISC_4_MASK (0xC000) -#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM (0x4000) -#define U300_SYSCON_PMC2R_APP_MISC_4_MMC (0x8000) -#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO (0xC000) -/* TODO: More SYSCON registers missing */ -#define U300_SYSCON_PMC3R (0x10c) -#define U300_SYSCON_PMC3R_APP_MISC_11_MASK (0xc000) -#define U300_SYSCON_PMC3R_APP_MISC_11_SPI (0x4000) -#define U300_SYSCON_PMC3R_APP_MISC_10_MASK (0x3000) -#define U300_SYSCON_PMC3R_APP_MISC_10_SPI (0x1000) -/* TODO: Missing other configs */ -#define U300_SYSCON_PMC4R (0x168) -#define U300_SYSCON_PMC4R_APP_MISC_12_MASK (0x0003) -#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_13_MASK (0x000C) -#define U300_SYSCON_PMC4R_APP_MISC_13_CDI (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA (0x0004) -#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 (0x0008) -#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO (0x000C) -#define U300_SYSCON_PMC4R_APP_MISC_14_MASK (0x0030) -#define U300_SYSCON_PMC4R_APP_MISC_14_CDI (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA (0x0010) -#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 (0x0020) -#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO (0x0030) -#define U300_SYSCON_PMC4R_APP_MISC_16_MASK (0x0300) -#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS (0x0100) -#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N (0x0200) /* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */ #define U300_SYSCON_S0CCR (0x120) #define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF) diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c index 677ccef..d5e4a98 100644 --- a/arch/arm/mach-u300/mmc.c +++ b/arch/arm/mach-u300/mmc.c @@ -21,7 +21,6 @@ #include <mach/dma_channels.h> #include "mmc.h" -#include "padmux.h" static struct mmci_platform_data mmc0_plat_data = { /* @@ -45,24 +44,9 @@ static struct mmci_platform_data mmc0_plat_data = { int __devinit mmc_init(struct amba_device *adev) { struct device *mmcsd_device = &adev->dev; - struct pmx *pmx; int ret = 0; mmcsd_device->platform_data = &mmc0_plat_data; - /* - * Setup padmuxing for MMC. Since this must always be - * compiled into the kernel, pmx is never released. - */ - pmx = pmx_get(mmcsd_device, U300_APP_PMX_MMC_SETTING); - - if (IS_ERR(pmx)) - pr_warning("Could not get padmux handle\n"); - else { - ret = pmx_activate(mmcsd_device, pmx); - if (IS_ERR_VALUE(ret)) - pr_warning("Could not activate padmuxing\n"); - } - return ret; } diff --git a/arch/arm/mach-u300/padmux.c b/arch/arm/mach-u300/padmux.c deleted file mode 100644 index 4c93c6c..0000000 --- a/arch/arm/mach-u300/padmux.c +++ /dev/null @@ -1,367 +0,0 @@ -/* - * - * arch/arm/mach-u300/padmux.c - * - * - * Copyright (C) 2009 ST-Ericsson AB - * License terms: GNU General Public License (GPL) version 2 - * U300 PADMUX functions - * Author: Martin Persson <martin.persson(a)stericsson.com> - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/device.h> -#include <linux/err.h> -#include <linux/errno.h> -#include <linux/io.h> -#include <linux/mutex.h> -#include <linux/string.h> -#include <linux/bug.h> -#include <linux/debugfs.h> -#include <linux/seq_file.h> -#include <mach/u300-regs.h> -#include <mach/syscon.h> -#include "padmux.h" - -static DEFINE_MUTEX(pmx_mutex); - -const u32 pmx_registers[] = { - (U300_SYSCON_VBASE + U300_SYSCON_PMC1LR), - (U300_SYSCON_VBASE + U300_SYSCON_PMC1HR), - (U300_SYSCON_VBASE + U300_SYSCON_PMC2R), - (U300_SYSCON_VBASE + U300_SYSCON_PMC3R), - (U300_SYSCON_VBASE + U300_SYSCON_PMC4R) -}; - -/* High level functionality */ - -/* Lazy dog: - * onmask = { - * {"PMC1LR" mask, "PMC1LR" value}, - * {"PMC1HR" mask, "PMC1HR" value}, - * {"PMC2R" mask, "PMC2R" value}, - * {"PMC3R" mask, "PMC3R" value}, - * {"PMC4R" mask, "PMC4R" value} - * } - */ -static struct pmx mmc_setting = { - .setting = U300_APP_PMX_MMC_SETTING, - .default_on = false, - .activated = false, - .name = "MMC", - .onmask = { - {U300_SYSCON_PMC1LR_MMCSD_MASK, - U300_SYSCON_PMC1LR_MMCSD_MMCSD}, - {0, 0}, - {0, 0}, - {0, 0}, - {U300_SYSCON_PMC4R_APP_MISC_12_MASK, - U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO} - }, -}; - -static struct pmx spi_setting = { - .setting = U300_APP_PMX_SPI_SETTING, - .default_on = false, - .activated = false, - .name = "SPI", - .onmask = {{0, 0}, - {U300_SYSCON_PMC1HR_APP_SPI_2_MASK | - U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK | - U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK, - U300_SYSCON_PMC1HR_APP_SPI_2_SPI | - U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI | - U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI}, - {0, 0}, - {0, 0}, - {0, 0} - }, -}; - -/* Available padmux settings */ -static struct pmx *pmx_settings[] = { - &mmc_setting, - &spi_setting, -}; - -static void update_registers(struct pmx *pmx, bool activate) -{ - u16 regval, val, mask; - int i; - - for (i = 0; i < ARRAY_SIZE(pmx_registers); i++) { - if (activate) - val = pmx->onmask[i].val; - else - val = 0; - - mask = pmx->onmask[i].mask; - if (mask != 0) { - regval = readw(pmx_registers[i]); - regval &= ~mask; - regval |= val; - writew(regval, pmx_registers[i]); - } - } -} - -struct pmx *pmx_get(struct device *dev, enum pmx_settings setting) -{ - int i; - struct pmx *pmx = ERR_PTR(-ENOENT); - - if (dev == NULL) - return ERR_PTR(-EINVAL); - - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (setting == pmx_settings[i]->setting) { - - if (pmx_settings[i]->dev != NULL) { - WARN(1, "padmux: required setting " - "in use by another consumer\n"); - } else { - pmx = pmx_settings[i]; - pmx->dev = dev; - dev_dbg(dev, "padmux: setting nr %d is now " - "bound to %s and ready to use\n", - setting, dev_name(dev)); - break; - } - } - } - mutex_unlock(&pmx_mutex); - - return pmx; -} -EXPORT_SYMBOL(pmx_get); - -int pmx_put(struct device *dev, struct pmx *pmx) -{ - int i; - int ret = -ENOENT; - - if (pmx == NULL || dev == NULL) - return -EINVAL; - - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (pmx->setting == pmx_settings[i]->setting) { - - if (dev != pmx->dev) { - WARN(1, "padmux: cannot release handle as " - "it is bound to another consumer\n"); - ret = -EINVAL; - break; - } else { - pmx_settings[i]->dev = NULL; - ret = 0; - break; - } - } - } - mutex_unlock(&pmx_mutex); - - return ret; -} -EXPORT_SYMBOL(pmx_put); - -int pmx_activate(struct device *dev, struct pmx *pmx) -{ - int i, j, ret; - ret = 0; - - if (pmx == NULL || dev == NULL) - return -EINVAL; - - mutex_lock(&pmx_mutex); - - /* Make sure the required bits are not used */ - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (pmx_settings[i]->dev == NULL || pmx_settings[i] == pmx) - continue; - - for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) { - - if (pmx_settings[i]->onmask[j].mask & pmx-> - onmask[j].mask) { - /* More than one entry on the same bits */ - WARN(1, "padmux: cannot activate " - "setting. Bit conflict with " - "an active setting\n"); - - ret = -EUSERS; - goto exit; - } - } - } - update_registers(pmx, true); - pmx->activated = true; - dev_dbg(dev, "padmux: setting nr %d is activated\n", - pmx->setting); - -exit: - mutex_unlock(&pmx_mutex); - return ret; -} -EXPORT_SYMBOL(pmx_activate); - -int pmx_deactivate(struct device *dev, struct pmx *pmx) -{ - int i; - int ret = -ENOENT; - - if (pmx == NULL || dev == NULL) - return -EINVAL; - - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (pmx_settings[i]->dev == NULL) - continue; - - if (pmx->setting == pmx_settings[i]->setting) { - - if (dev != pmx->dev) { - WARN(1, "padmux: cannot deactivate " - "pmx setting as it was activated " - "by another consumer\n"); - - ret = -EBUSY; - continue; - } else { - update_registers(pmx, false); - pmx_settings[i]->dev = NULL; - pmx->activated = false; - ret = 0; - dev_dbg(dev, "padmux: setting nr %d is deactivated", - pmx->setting); - break; - } - } - } - mutex_unlock(&pmx_mutex); - - return ret; -} -EXPORT_SYMBOL(pmx_deactivate); - -/* - * For internal use only. If it is to be exported, - * it should be reentrant. Notice that pmx_activate - * (i.e. runtime settings) always override default settings. - */ -static int pmx_set_default(void) -{ - /* Used to identify several entries on the same bits */ - u16 modbits[ARRAY_SIZE(pmx_registers)]; - - int i, j; - - memset(modbits, 0, ARRAY_SIZE(pmx_registers) * sizeof(u16)); - - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (!pmx_settings[i]->default_on) - continue; - - for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) { - - /* Make sure there is only one entry on the same bits */ - if (modbits[j] & pmx_settings[i]->onmask[j].mask) { - BUG(); - return -EUSERS; - } - modbits[j] |= pmx_settings[i]->onmask[j].mask; - } - update_registers(pmx_settings[i], true); - } - return 0; -} - -#if (defined(CONFIG_DEBUG_FS) && defined(CONFIG_U300_DEBUG)) -static int pmx_show(struct seq_file *s, void *data) -{ - int i; - seq_printf(s, "-------------------------------------------------\n"); - seq_printf(s, "SETTING BOUND TO DEVICE STATE\n"); - seq_printf(s, "-------------------------------------------------\n"); - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - /* Format pmx and device name nicely */ - char cdp[33]; - int chars; - - chars = snprintf(&cdp[0], 17, "%s", pmx_settings[i]->name); - while (chars < 16) { - cdp[chars] = ' '; - chars++; - } - chars = snprintf(&cdp[16], 17, "%s", pmx_settings[i]->dev ? - dev_name(pmx_settings[i]->dev) : "N/A"); - while (chars < 16) { - cdp[chars+16] = ' '; - chars++; - } - cdp[32] = '\0'; - - seq_printf(s, - "%s\t%s\n", - &cdp[0], - pmx_settings[i]->activated ? - "ACTIVATED" : "DEACTIVATED" - ); - - } - mutex_unlock(&pmx_mutex); - return 0; -} - -static int pmx_open(struct inode *inode, struct file *file) -{ - return single_open(file, pmx_show, NULL); -} - -static const struct file_operations pmx_operations = { - .owner = THIS_MODULE, - .open = pmx_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; - -static int __init init_pmx_read_debugfs(void) -{ - /* Expose a simple debugfs interface to view pmx settings */ - (void) debugfs_create_file("padmux", S_IFREG | S_IRUGO, - NULL, NULL, - &pmx_operations); - return 0; -} - -/* - * This needs to come in after the core_initcall(), - * because debugfs is not available until - * the subsystems come up. - */ -module_init(init_pmx_read_debugfs); -#endif - -static int __init pmx_init(void) -{ - int ret; - - ret = pmx_set_default(); - - if (IS_ERR_VALUE(ret)) - pr_crit("padmux: default settings could not be set\n"); - - return 0; -} - -/* Should be initialized before consumers */ -core_initcall(pmx_init); diff --git a/arch/arm/mach-u300/padmux.h b/arch/arm/mach-u300/padmux.h deleted file mode 100644 index 6e8b860..0000000 --- a/arch/arm/mach-u300/padmux.h +++ /dev/null @@ -1,39 +0,0 @@ -/* - * - * arch/arm/mach-u300/padmux.h - * - * - * Copyright (C) 2009 ST-Ericsson AB - * License terms: GNU General Public License (GPL) version 2 - * U300 PADMUX API - * Author: Martin Persson <martin.persson(a)stericsson.com> - */ - -#ifndef __MACH_U300_PADMUX_H -#define __MACH_U300_PADMUX_H - -enum pmx_settings { - U300_APP_PMX_MMC_SETTING, - U300_APP_PMX_SPI_SETTING -}; - -struct pmx_onmask { - u16 mask; /* Mask bits */ - u16 val; /* Value when active */ -}; - -struct pmx { - struct device *dev; - enum pmx_settings setting; - char *name; - bool activated; - bool default_on; - struct pmx_onmask onmask[]; -}; - -struct pmx *pmx_get(struct device *dev, enum pmx_settings setting); -int pmx_put(struct device *dev, struct pmx *pmx); -int pmx_activate(struct device *dev, struct pmx *pmx); -int pmx_deactivate(struct device *dev, struct pmx *pmx); - -#endif diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c index 7b597e2..a1affac 100644 --- a/arch/arm/mach-u300/spi.c +++ b/arch/arm/mach-u300/spi.c @@ -14,8 +14,6 @@ #include <mach/coh901318.h> #include <mach/dma_channels.h> -#include "padmux.h" - /* * The following is for the actual devices on the SSP/SPI bus */ @@ -95,25 +93,7 @@ static struct pl022_ssp_controller ssp_platform_data = { void __init u300_spi_init(struct amba_device *adev) { - struct pmx *pmx; - adev->dev.platform_data = &ssp_platform_data; - /* - * Setup padmuxing for SPI. Since this must always be - * compiled into the kernel, pmx is never released. - */ - pmx = pmx_get(&adev->dev, U300_APP_PMX_SPI_SETTING); - - if (IS_ERR(pmx)) - dev_warn(&adev->dev, "Could not get padmux handle\n"); - else { - int ret; - - ret = pmx_activate(&adev->dev, pmx); - if (IS_ERR_VALUE(ret)) - dev_warn(&adev->dev, "Could not activate padmuxing\n"); - } - } void __init u300_spi_register_board_devices(void) diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 02b4d4e..7b175c3 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -26,4 +26,11 @@ config DEBUG_PINCTRL help Say Y here to add some extra checks and diagnostics to PINCTRL calls. +config PINMUX_U300 + bool "U300 pinmux driver" + depends on ARCH_U300 + select PINMUX + help + Say Y here to enable the U300 pinmux driver + endif diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index 596ce9f..63d4241 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -4,3 +4,4 @@ ccflags-$(CONFIG_DEBUG_PINMUX) += -DDEBUG obj-$(CONFIG_PINCTRL) += core.o obj-$(CONFIG_PINMUX) += pinmux.o +obj-$(CONFIG_PINMUX_U300) += pinmux-u300.o diff --git a/drivers/pinctrl/pinmux-u300.c b/drivers/pinctrl/pinmux-u300.c new file mode 100644 index 0000000..23f082f --- /dev/null +++ b/drivers/pinctrl/pinmux-u300.c @@ -0,0 +1,1135 @@ +/* + * Driver for the U300 pin controller + * + * Based on the original U300 padmux functions + * Copyright (C) 2009-2011 ST-Ericsson AB + * Author: Martin Persson <martin.persson(a)stericsson.com> + * Author: Linus Walleij <linus.walleij(a)linaro.org> + * + * The DB3350 design and control registers are oriented around pads rather than + * pins, so we enumerate the pads we can mux rather than actual pins. The pads + * are connected to different pins in different packaging types, so it would + * be confusing. + */ +#include <linux/init.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/err.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> + +/* + * Register definitions for the U300 Padmux control registers in the + * system controller + */ + +/* PAD MUX Control register 1 (LOW) 16bit (R/W) */ +#define U300_SYSCON_PMC1LR 0x007C +#define U300_SYSCON_PMC1LR_MASK 0xFFFF +#define U300_SYSCON_PMC1LR_CDI_MASK 0xC000 +#define U300_SYSCON_PMC1LR_CDI_CDI 0x0000 +#define U300_SYSCON_PMC1LR_CDI_EMIF 0x4000 +/* For BS335 */ +#define U300_SYSCON_PMC1LR_CDI_CDI2 0x8000 +#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO 0xC000 +/* For BS365 */ +#define U300_SYSCON_PMC1LR_CDI_GPIO 0x8000 +#define U300_SYSCON_PMC1LR_CDI_WCDMA 0xC000 +/* Common defs */ +#define U300_SYSCON_PMC1LR_PDI_MASK 0x3000 +#define U300_SYSCON_PMC1LR_PDI_PDI 0x0000 +#define U300_SYSCON_PMC1LR_PDI_EGG 0x1000 +#define U300_SYSCON_PMC1LR_PDI_WCDMA 0x3000 +#define U300_SYSCON_PMC1LR_MMCSD_MASK 0x0C00 +#define U300_SYSCON_PMC1LR_MMCSD_MMCSD 0x0000 +#define U300_SYSCON_PMC1LR_MMCSD_MSPRO 0x0400 +#define U300_SYSCON_PMC1LR_MMCSD_DSP 0x0800 +#define U300_SYSCON_PMC1LR_MMCSD_WCDMA 0x0C00 +#define U300_SYSCON_PMC1LR_ETM_MASK 0x0300 +#define U300_SYSCON_PMC1LR_ETM_ACC 0x0000 +#define U300_SYSCON_PMC1LR_ETM_APP 0x0100 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK 0x00C0 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF 0x0040 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM 0x0080 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB 0x00C0 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK 0x0030 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF 0x0010 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM 0x0020 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI 0x0030 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK 0x000C +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF 0x0004 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM 0x0008 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI 0x000C +#define U300_SYSCON_PMC1LR_EMIF_1_MASK 0x0003 +#define U300_SYSCON_PMC1LR_EMIF_1_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 0x0001 +#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1 0x0002 +#define U300_SYSCON_PMC1LR_EMIF_1 0x0003 +/* PAD MUX Control register 2 (HIGH) 16bit (R/W) */ +#define U300_SYSCON_PMC1HR 0x007E +#define U300_SYSCON_PMC1HR_MASK 0xFFFF +#define U300_SYSCON_PMC1HR_MISC_2_MASK 0xC000 +#define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_MISC_2_MSPRO 0x4000 +#define U300_SYSCON_PMC1HR_MISC_2_DSP 0x8000 +#define U300_SYSCON_PMC1HR_MISC_2_AAIF 0xC000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK 0x3000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF 0x1000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP 0x2000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF 0x3000 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK 0x0C00 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC 0x0400 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP 0x0800 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF 0x0C00 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK 0x0300 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI 0x0100 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF 0x0300 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK 0x00C0 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI 0x0040 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF 0x00C0 +#define U300_SYSCON_PMC1HR_APP_SPI_2_MASK 0x0030 +#define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_SPI_2_SPI 0x0010 +#define U300_SYSCON_PMC1HR_APP_SPI_2_DSP 0x0020 +#define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF 0x0030 +#define U300_SYSCON_PMC1HR_APP_UART0_2_MASK 0x000C +#define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_UART0_2_UART0 0x0004 +#define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS 0x0008 +#define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF 0x000C +#define U300_SYSCON_PMC1HR_APP_UART0_1_MASK 0x0003 +#define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_UART0_1_UART0 0x0001 +#define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF 0x0003 +/* Padmux 2 control */ +#define U300_SYSCON_PMC2R 0x100 +#define U300_SYSCON_PMC2R_APP_MISC_0_MASK 0x00C0 +#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM 0x0040 +#define U300_SYSCON_PMC2R_APP_MISC_0_MMC 0x0080 +#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 0x00C0 +#define U300_SYSCON_PMC2R_APP_MISC_1_MASK 0x0300 +#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM 0x0100 +#define U300_SYSCON_PMC2R_APP_MISC_1_MMC 0x0200 +#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 0x0300 +#define U300_SYSCON_PMC2R_APP_MISC_2_MASK 0x0C00 +#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM 0x0400 +#define U300_SYSCON_PMC2R_APP_MISC_2_MMC 0x0800 +#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 0x0C00 +#define U300_SYSCON_PMC2R_APP_MISC_3_MASK 0x3000 +#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM 0x1000 +#define U300_SYSCON_PMC2R_APP_MISC_3_MMC 0x2000 +#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 0x3000 +#define U300_SYSCON_PMC2R_APP_MISC_4_MASK 0xC000 +#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM 0x4000 +#define U300_SYSCON_PMC2R_APP_MISC_4_MMC 0x8000 +#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO 0xC000 +/* TODO: More SYSCON registers missing */ +#define U300_SYSCON_PMC3R 0x10C +#define U300_SYSCON_PMC3R_APP_MISC_11_MASK 0xC000 +#define U300_SYSCON_PMC3R_APP_MISC_11_SPI 0x4000 +#define U300_SYSCON_PMC3R_APP_MISC_10_MASK 0x3000 +#define U300_SYSCON_PMC3R_APP_MISC_10_SPI 0x1000 +/* TODO: Missing other configs */ +#define U300_SYSCON_PMC4R 0x168 +#define U300_SYSCON_PMC4R_APP_MISC_12_MASK 0x0003 +#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_13_MASK 0x000C +#define U300_SYSCON_PMC4R_APP_MISC_13_CDI 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA 0x0004 +#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 0x0008 +#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO 0x000C +#define U300_SYSCON_PMC4R_APP_MISC_14_MASK 0x0030 +#define U300_SYSCON_PMC4R_APP_MISC_14_CDI 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA 0x0010 +#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 0x0020 +#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO 0x0030 +#define U300_SYSCON_PMC4R_APP_MISC_16_MASK 0x0300 +#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS 0x0100 +#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N 0x0200 + +#define DRIVER_NAME "pinmux-u300" + +/* + * The DB3350 has 467 pads, I have enumerated the pads clockwise around the + * edges of the silicon, finger by finger. LTCORNER upper left is pad 0. + * Data taken from the PadRing chart, arranged like this: + * + * 0 ..... 104 + * 466 105 + * . . + * . . + * 358 224 + * 357 .... 225 + */ +#define U300_NUM_PADS 467 + +/* Pad names for the pinmux subsystem */ +static const struct pinctrl_pin_desc __refdata u300_pads[] = { + /* Pads along the top edge of the chip */ + PINCTRL_PIN(0, "P PAD VDD 28"), + PINCTRL_PIN(1, "P PAD GND 28"), + PINCTRL_PIN(2, "PO SIM RST N"), + PINCTRL_PIN(3, "VSSIO 25"), + PINCTRL_PIN(4, "VSSA ADDA ESDSUB"), + PINCTRL_PIN(5, "PWR VSSCOMMON"), + PINCTRL_PIN(6, "PI ADC I1 POS"), + PINCTRL_PIN(7, "PI ADC I1 NEG"), + PINCTRL_PIN(8, "PWR VSSAD0"), + PINCTRL_PIN(9, "PWR VCCAD0"), + PINCTRL_PIN(10, "PI ADC Q1 NEG"), + PINCTRL_PIN(11, "PI ADC Q1 POS"), + PINCTRL_PIN(12, "PWR VDDAD"), + PINCTRL_PIN(13, "PWR GNDAD"), + PINCTRL_PIN(14, "PI ADC I2 POS"), + PINCTRL_PIN(15, "PI ADC I2 NEG"), + PINCTRL_PIN(16, "PWR VSSAD1"), + PINCTRL_PIN(17, "PWR VCCAD1"), + PINCTRL_PIN(18, "PI ADC Q2 NEG"), + PINCTRL_PIN(19, "PI ADC Q2 POS"), + PINCTRL_PIN(20, "VSSA ADDA ESDSUB"), + PINCTRL_PIN(21, "PWR VCCGPAD"), + PINCTRL_PIN(22, "PI TX POW"), + PINCTRL_PIN(23, "PWR VSSGPAD"), + PINCTRL_PIN(24, "PO DAC I POS"), + PINCTRL_PIN(25, "PO DAC I NEG"), + PINCTRL_PIN(26, "PO DAC Q POS"), + PINCTRL_PIN(27, "PO DAC Q NEG"), + PINCTRL_PIN(28, "PWR VSSDA"), + PINCTRL_PIN(29, "PWR VCCDA"), + PINCTRL_PIN(30, "VSSA ADDA ESDSUB"), + PINCTRL_PIN(31, "P PAD VDDIO 11"), + PINCTRL_PIN(32, "PI PLL 26 FILTVDD"), + PINCTRL_PIN(33, "PI PLL 26 VCONT"), + PINCTRL_PIN(34, "PWR AGNDPLL2V5 32 13"), + PINCTRL_PIN(35, "PWR AVDDPLL2V5 32 13"), + PINCTRL_PIN(36, "VDDA PLL ESD"), + PINCTRL_PIN(37, "VSSA PLL ESD"), + PINCTRL_PIN(38, "VSS PLL"), + PINCTRL_PIN(39, "VDDC PLL"), + PINCTRL_PIN(40, "PWR AGNDPLL2V5 26 60"), + PINCTRL_PIN(41, "PWR AVDDPLL2V5 26 60"), + PINCTRL_PIN(42, "PWR AVDDPLL2V5 26 208"), + PINCTRL_PIN(43, "PWR AGNDPLL2V5 26 208"), + PINCTRL_PIN(44, "PWR AVDDPLL2V5 13 208"), + PINCTRL_PIN(45, "PWR AGNDPLL2V5 13 208"), + PINCTRL_PIN(46, "P PAD VSSIO 11"), + PINCTRL_PIN(47, "P PAD VSSIO 12"), + PINCTRL_PIN(48, "PI POW RST N"), + PINCTRL_PIN(49, "VDDC IO"), + PINCTRL_PIN(50, "P PAD VDDIO 16"), + PINCTRL_PIN(51, "PO RF WCDMA EN 4"), + PINCTRL_PIN(52, "PO RF WCDMA EN 3"), + PINCTRL_PIN(53, "PO RF WCDMA EN 2"), + PINCTRL_PIN(54, "PO RF WCDMA EN 1"), + PINCTRL_PIN(55, "PO RF WCDMA EN 0"), + PINCTRL_PIN(56, "PO GSM PA ENABLE"), + PINCTRL_PIN(57, "PO RF DATA STRB"), + PINCTRL_PIN(58, "PO RF DATA2"), + PINCTRL_PIN(59, "PIO RF DATA1"), + PINCTRL_PIN(60, "PIO RF DATA0"), + PINCTRL_PIN(61, "P PAD VDD 11"), + PINCTRL_PIN(62, "P PAD GND 11"), + PINCTRL_PIN(63, "P PAD VSSIO 16"), + PINCTRL_PIN(64, "P PAD VDDIO 18"), + PINCTRL_PIN(65, "PO RF CTRL STRB2"), + PINCTRL_PIN(66, "PO RF CTRL STRB1"), + PINCTRL_PIN(67, "PO RF CTRL STRB0"), + PINCTRL_PIN(68, "PIO RF CTRL DATA"), + PINCTRL_PIN(69, "PO RF CTRL CLK"), + PINCTRL_PIN(70, "PO TX ADC STRB"), + PINCTRL_PIN(71, "PO ANT SW 2"), + PINCTRL_PIN(72, "PO ANT SW 3"), + PINCTRL_PIN(73, "PO ANT SW 0"), + PINCTRL_PIN(74, "PO ANT SW 1"), + PINCTRL_PIN(75, "PO M CLKRQ"), + PINCTRL_PIN(76, "PI M CLK"), + PINCTRL_PIN(77, "PI RTC CLK"), + PINCTRL_PIN(78, "P PAD VDD 8"), + PINCTRL_PIN(79, "P PAD GND 8"), + PINCTRL_PIN(80, "P PAD VSSIO 13"), + PINCTRL_PIN(81, "P PAD VDDIO 13"), + PINCTRL_PIN(82, "PO SYS 1 CLK"), + PINCTRL_PIN(83, "PO SYS 2 CLK"), + PINCTRL_PIN(84, "PO SYS 0 CLK"), + PINCTRL_PIN(85, "PI SYS 0 CLKRQ"), + PINCTRL_PIN(86, "PO PWR MNGT CTRL 1"), + PINCTRL_PIN(87, "PO PWR MNGT CTRL 0"), + PINCTRL_PIN(88, "PO RESOUT2 RST N"), + PINCTRL_PIN(89, "PO RESOUT1 RST N"), + PINCTRL_PIN(90, "PO RESOUT0 RST N"), + PINCTRL_PIN(91, "PI SERVICE N"), + PINCTRL_PIN(92, "P PAD VDD 29"), + PINCTRL_PIN(93, "P PAD GND 29"), + PINCTRL_PIN(94, "P PAD VSSIO 8"), + PINCTRL_PIN(95, "P PAD VDDIO 8"), + PINCTRL_PIN(96, "PI EXT IRQ1 N"), + PINCTRL_PIN(97, "PI EXT IRQ0 N"), + PINCTRL_PIN(98, "PIO DC ON"), + PINCTRL_PIN(99, "PIO ACC APP I2C DATA"), + PINCTRL_PIN(100, "PIO ACC APP I2C CLK"), + PINCTRL_PIN(101, "P PAD VDD 12"), + PINCTRL_PIN(102, "P PAD GND 12"), + PINCTRL_PIN(103, "P PAD VSSIO 14"), + PINCTRL_PIN(104, "P PAD VDDIO 14"), + /* Pads along the right edge of the chip */ + PINCTRL_PIN(105, "PIO APP I2C1 DATA"), + PINCTRL_PIN(106, "PIO APP I2C1 CLK"), + PINCTRL_PIN(107, "PO KEY OUT0"), + PINCTRL_PIN(108, "PO KEY OUT1"), + PINCTRL_PIN(109, "PO KEY OUT2"), + PINCTRL_PIN(110, "PO KEY OUT3"), + PINCTRL_PIN(111, "PO KEY OUT4"), + PINCTRL_PIN(112, "PI KEY IN0"), + PINCTRL_PIN(113, "PI KEY IN1"), + PINCTRL_PIN(114, "PI KEY IN2"), + PINCTRL_PIN(115, "P PAD VDDIO 15"), + PINCTRL_PIN(116, "P PAD VSSIO 15"), + PINCTRL_PIN(117, "P PAD GND 13"), + PINCTRL_PIN(118, "P PAD VDD 13"), + PINCTRL_PIN(119, "PI KEY IN3"), + PINCTRL_PIN(120, "PI KEY IN4"), + PINCTRL_PIN(121, "PI KEY IN5"), + PINCTRL_PIN(122, "PIO APP PCM I2S1 DATA B"), + PINCTRL_PIN(123, "PIO APP PCM I2S1 DATA A"), + PINCTRL_PIN(124, "PIO APP PCM I2S1 WS"), + PINCTRL_PIN(125, "PIO APP PCM I2S1 CLK"), + PINCTRL_PIN(126, "PIO APP PCM I2S0 DATA B"), + PINCTRL_PIN(127, "PIO APP PCM I2S0 DATA A"), + PINCTRL_PIN(128, "PIO APP PCM I2S0 WS"), + PINCTRL_PIN(129, "PIO APP PCM I2S0 CLK"), + PINCTRL_PIN(130, "P PAD VDD 17"), + PINCTRL_PIN(131, "P PAD GND 17"), + PINCTRL_PIN(132, "P PAD VSSIO 19"), + PINCTRL_PIN(133, "P PAD VDDIO 19"), + PINCTRL_PIN(134, "UART0 RTS"), + PINCTRL_PIN(135, "UART0 CTS"), + PINCTRL_PIN(136, "UART0 TX"), + PINCTRL_PIN(137, "UART0 RX"), + PINCTRL_PIN(138, "PIO ACC SPI DO"), + PINCTRL_PIN(139, "PIO ACC SPI DI"), + PINCTRL_PIN(140, "PIO ACC SPI CS0 N"), + PINCTRL_PIN(141, "PIO ACC SPI CS1 N"), + PINCTRL_PIN(142, "PIO ACC SPI CS2 N"), + PINCTRL_PIN(143, "PIO ACC SPI CLK"), + PINCTRL_PIN(144, "PO PDI EXT RST N"), + PINCTRL_PIN(145, "P PAD VDDIO 22"), + PINCTRL_PIN(146, "P PAD VSSIO 22"), + PINCTRL_PIN(147, "P PAD GND 18"), + PINCTRL_PIN(148, "P PAD VDD 18"), + PINCTRL_PIN(149, "PIO PDI C0"), + PINCTRL_PIN(150, "PIO PDI C1"), + PINCTRL_PIN(151, "PIO PDI C2"), + PINCTRL_PIN(152, "PIO PDI C3"), + PINCTRL_PIN(153, "PIO PDI C4"), + PINCTRL_PIN(154, "PIO PDI C5"), + PINCTRL_PIN(155, "PIO PDI D0"), + PINCTRL_PIN(156, "PIO PDI D1"), + PINCTRL_PIN(157, "PIO PDI D2"), + PINCTRL_PIN(158, "PIO PDI D3"), + PINCTRL_PIN(159, "P PAD VDDIO 21"), + PINCTRL_PIN(160, "P PAD VSSIO 21"), + PINCTRL_PIN(161, "PIO PDI D4"), + PINCTRL_PIN(162, "PIO PDI D5"), + PINCTRL_PIN(163, "PIO PDI D6"), + PINCTRL_PIN(164, "PIO PDI D7"), + PINCTRL_PIN(165, "PIO MS INS"), + PINCTRL_PIN(166, "MMC DATA DIR LS"), + PINCTRL_PIN(167, "MMC DATA 3"), + PINCTRL_PIN(168, "MMC DATA 2"), + PINCTRL_PIN(169, "MMC DATA 1"), + PINCTRL_PIN(170, "MMC DATA 0"), + PINCTRL_PIN(171, "MMC CMD DIR LS"), + PINCTRL_PIN(172, "P PAD VDD 27"), + PINCTRL_PIN(173, "P PAD GND 27"), + PINCTRL_PIN(174, "P PAD VSSIO 20"), + PINCTRL_PIN(175, "P PAD VDDIO 20"), + PINCTRL_PIN(176, "MMC CMD"), + PINCTRL_PIN(177, "MMC CLK"), + PINCTRL_PIN(178, "PIO APP GPIO 14"), + PINCTRL_PIN(179, "PIO APP GPIO 13"), + PINCTRL_PIN(180, "PIO APP GPIO 11"), + PINCTRL_PIN(181, "PIO APP GPIO 25"), + PINCTRL_PIN(182, "PIO APP GPIO 24"), + PINCTRL_PIN(183, "PIO APP GPIO 23"), + PINCTRL_PIN(184, "PIO APP GPIO 22"), + PINCTRL_PIN(185, "PIO APP GPIO 21"), + PINCTRL_PIN(186, "PIO APP GPIO 20"), + PINCTRL_PIN(187, "P PAD VDD 19"), + PINCTRL_PIN(188, "P PAD GND 19"), + PINCTRL_PIN(189, "P PAD VSSIO 23"), + PINCTRL_PIN(190, "P PAD VDDIO 23"), + PINCTRL_PIN(191, "PIO APP GPIO 19"), + PINCTRL_PIN(192, "PIO APP GPIO 18"), + PINCTRL_PIN(193, "PIO APP GPIO 17"), + PINCTRL_PIN(194, "PIO APP GPIO 16"), + PINCTRL_PIN(195, "PI CI D1"), + PINCTRL_PIN(196, "PI CI D0"), + PINCTRL_PIN(197, "PI CI HSYNC"), + PINCTRL_PIN(198, "PI CI VSYNC"), + PINCTRL_PIN(199, "PI CI EXT CLK"), + PINCTRL_PIN(200, "PO CI EXT RST N"), + PINCTRL_PIN(201, "P PAD VSSIO 43"), + PINCTRL_PIN(202, "P PAD VDDIO 43"), + PINCTRL_PIN(203, "PI CI D6"), + PINCTRL_PIN(204, "PI CI D7"), + PINCTRL_PIN(205, "PI CI D2"), + PINCTRL_PIN(206, "PI CI D3"), + PINCTRL_PIN(207, "PI CI D4"), + PINCTRL_PIN(208, "PI CI D5"), + PINCTRL_PIN(209, "PI CI D8"), + PINCTRL_PIN(210, "PI CI D9"), + PINCTRL_PIN(211, "P PAD VDD 20"), + PINCTRL_PIN(212, "P PAD GND 20"), + PINCTRL_PIN(213, "P PAD VSSIO 24"), + PINCTRL_PIN(214, "P PAD VDDIO 24"), + PINCTRL_PIN(215, "P PAD VDDIO 26"), + PINCTRL_PIN(216, "PO EMIF 1 A26"), + PINCTRL_PIN(217, "PO EMIF 1 A25"), + PINCTRL_PIN(218, "P PAD VSSIO 26"), + PINCTRL_PIN(219, "PO EMIF 1 A24"), + PINCTRL_PIN(220, "PO EMIF 1 A23"), + /* Pads along the bottom edge of the chip */ + PINCTRL_PIN(221, "PO EMIF 1 A22"), + PINCTRL_PIN(222, "PO EMIF 1 A21"), + PINCTRL_PIN(223, "P PAD VDD 21"), + PINCTRL_PIN(224, "P PAD GND 21"), + PINCTRL_PIN(225, "P PAD VSSIO 27"), + PINCTRL_PIN(226, "P PAD VDDIO 27"), + PINCTRL_PIN(227, "PO EMIF 1 A20"), + PINCTRL_PIN(228, "PO EMIF 1 A19"), + PINCTRL_PIN(229, "PO EMIF 1 A18"), + PINCTRL_PIN(230, "PO EMIF 1 A17"), + PINCTRL_PIN(231, "P PAD VDDIO 28"), + PINCTRL_PIN(232, "P PAD VSSIO 28"), + PINCTRL_PIN(233, "PO EMIF 1 A16"), + PINCTRL_PIN(234, "PIO EMIF 1 D15"), + PINCTRL_PIN(235, "PO EMIF 1 A15"), + PINCTRL_PIN(236, "PIO EMIF 1 D14"), + PINCTRL_PIN(237, "P PAD VDD 22"), + PINCTRL_PIN(238, "P PAD GND 22"), + PINCTRL_PIN(239, "P PAD VSSIO 29"), + PINCTRL_PIN(240, "P PAD VDDIO 29"), + PINCTRL_PIN(241, "PO EMIF 1 A14"), + PINCTRL_PIN(242, "PIO EMIF 1 D13"), + PINCTRL_PIN(243, "PO EMIF 1 A13"), + PINCTRL_PIN(244, "PIO EMIF 1 D12"), + PINCTRL_PIN(245, "P PAD VSSIO 30"), + PINCTRL_PIN(246, "P PAD VDDIO 30"), + PINCTRL_PIN(247, "PO EMIF 1 A12"), + PINCTRL_PIN(248, "PIO EMIF 1 D11"), + PINCTRL_PIN(249, "PO EMIF 1 A11"), + PINCTRL_PIN(250, "PIO EMIF 1 D10"), + PINCTRL_PIN(251, "P PAD VSSIO 31"), + PINCTRL_PIN(252, "P PAD VDDIO 31"), + PINCTRL_PIN(253, "PO EMIF 1 A10"), + PINCTRL_PIN(254, "PIO EMIF 1 D09"), + PINCTRL_PIN(255, "PO EMIF 1 A09"), + PINCTRL_PIN(256, "P PAD VDDIO 32"), + PINCTRL_PIN(257, "P PAD VSSIO 32"), + PINCTRL_PIN(258, "P PAD GND 24"), + PINCTRL_PIN(259, "P PAD VDD 24"), + PINCTRL_PIN(260, "PIO EMIF 1 D08"), + PINCTRL_PIN(261, "PO EMIF 1 A08"), + PINCTRL_PIN(262, "PIO EMIF 1 D07"), + PINCTRL_PIN(263, "PO EMIF 1 A07"), + PINCTRL_PIN(264, "P PAD VDDIO 33"), + PINCTRL_PIN(265, "P PAD VSSIO 33"), + PINCTRL_PIN(266, "PIO EMIF 1 D06"), + PINCTRL_PIN(267, "PO EMIF 1 A06"), + PINCTRL_PIN(268, "PIO EMIF 1 D05"), + PINCTRL_PIN(269, "PO EMIF 1 A05"), + PINCTRL_PIN(270, "P PAD VDDIO 34"), + PINCTRL_PIN(271, "P PAD VSSIO 34"), + PINCTRL_PIN(272, "PIO EMIF 1 D04"), + PINCTRL_PIN(273, "PO EMIF 1 A04"), + PINCTRL_PIN(274, "PIO EMIF 1 D03"), + PINCTRL_PIN(275, "PO EMIF 1 A03"), + PINCTRL_PIN(276, "P PAD VDDIO 35"), + PINCTRL_PIN(277, "P PAD VSSIO 35"), + PINCTRL_PIN(278, "P PAD GND 23"), + PINCTRL_PIN(279, "P PAD VDD 23"), + PINCTRL_PIN(280, "PIO EMIF 1 D02"), + PINCTRL_PIN(281, "PO EMIF 1 A02"), + PINCTRL_PIN(282, "PIO EMIF 1 D01"), + PINCTRL_PIN(283, "PO EMIF 1 A01"), + PINCTRL_PIN(284, "P PAD VDDIO 36"), + PINCTRL_PIN(285, "P PAD VSSIO 36"), + PINCTRL_PIN(286, "PIO EMIF 1 D00"), + PINCTRL_PIN(287, "PO EMIF 1 BE1 N"), + PINCTRL_PIN(288, "PO EMIF 1 BE0 N"), + PINCTRL_PIN(289, "PO EMIF 1 ADV N"), + PINCTRL_PIN(290, "P PAD VDDIO 37"), + PINCTRL_PIN(291, "P PAD VSSIO 37"), + PINCTRL_PIN(292, "PO EMIF 1 SD CKE0"), + PINCTRL_PIN(293, "PO EMIF 1 OE N"), + PINCTRL_PIN(294, "PO EMIF 1 WE N"), + PINCTRL_PIN(295, "P PAD VDDIO 38"), + PINCTRL_PIN(296, "P PAD VSSIO 38"), + PINCTRL_PIN(297, "PO EMIF 1 CLK"), + PINCTRL_PIN(298, "PIO EMIF 1 SD CLK"), + PINCTRL_PIN(299, "P PAD VSSIO 45 (not bonded)"), + PINCTRL_PIN(300, "P PAD VDDIO 42"), + PINCTRL_PIN(301, "P PAD VSSIO 42"), + PINCTRL_PIN(302, "P PAD GND 31"), + PINCTRL_PIN(303, "P PAD VDD 31"), + PINCTRL_PIN(304, "PI EMIF 1 RET CLK"), + PINCTRL_PIN(305, "PI EMIF 1 WAIT N"), + PINCTRL_PIN(306, "PI EMIF 1 NFIF READY"), + PINCTRL_PIN(307, "PO EMIF 1 SD CKE1"), + PINCTRL_PIN(308, "PO EMIF 1 CS3 N"), + PINCTRL_PIN(309, "P PAD VDD 25"), + PINCTRL_PIN(310, "P PAD GND 25"), + PINCTRL_PIN(311, "P PAD VSSIO 39"), + PINCTRL_PIN(312, "P PAD VDDIO 39"), + PINCTRL_PIN(313, "PO EMIF 1 CS2 N"), + PINCTRL_PIN(314, "PO EMIF 1 CS1 N"), + PINCTRL_PIN(315, "PO EMIF 1 CS0 N"), + PINCTRL_PIN(316, "PO ETM TRACE PKT0"), + PINCTRL_PIN(317, "PO ETM TRACE PKT1"), + PINCTRL_PIN(318, "PO ETM TRACE PKT2"), + PINCTRL_PIN(319, "P PAD VDD 30"), + PINCTRL_PIN(320, "P PAD GND 30"), + PINCTRL_PIN(321, "P PAD VSSIO 44"), + PINCTRL_PIN(322, "P PAD VDDIO 44"), + PINCTRL_PIN(323, "PO ETM TRACE PKT3"), + PINCTRL_PIN(324, "PO ETM TRACE PKT4"), + PINCTRL_PIN(325, "PO ETM TRACE PKT5"), + PINCTRL_PIN(326, "PO ETM TRACE PKT6"), + PINCTRL_PIN(327, "PO ETM TRACE PKT7"), + PINCTRL_PIN(328, "PO ETM PIPE STAT0"), + PINCTRL_PIN(329, "P PAD VDD 26"), + PINCTRL_PIN(330, "P PAD GND 26"), + PINCTRL_PIN(331, "P PAD VSSIO 40"), + PINCTRL_PIN(332, "P PAD VDDIO 40"), + PINCTRL_PIN(333, "PO ETM PIPE STAT1"), + PINCTRL_PIN(334, "PO ETM PIPE STAT2"), + PINCTRL_PIN(335, "PO ETM TRACE CLK"), + PINCTRL_PIN(336, "PO ETM TRACE SYNC"), + PINCTRL_PIN(337, "PIO ACC GPIO 33"), + PINCTRL_PIN(338, "PIO ACC GPIO 32"), + PINCTRL_PIN(339, "PIO ACC GPIO 30"), + PINCTRL_PIN(340, "PIO ACC GPIO 29"), + PINCTRL_PIN(341, "P PAD VDDIO 17"), + PINCTRL_PIN(342, "P PAD VSSIO 17"), + PINCTRL_PIN(343, "P PAD GND 15"), + PINCTRL_PIN(344, "P PAD VDD 15"), + PINCTRL_PIN(345, "PIO ACC GPIO 28"), + PINCTRL_PIN(346, "PIO ACC GPIO 27"), + PINCTRL_PIN(347, "PIO ACC GPIO 16"), + PINCTRL_PIN(348, "PI TAP TMS"), + PINCTRL_PIN(349, "PI TAP TDI"), + PINCTRL_PIN(350, "PO TAP TDO"), + PINCTRL_PIN(351, "PI TAP RST N"), + /* Pads along the left edge of the chip */ + PINCTRL_PIN(352, "PI EMU MODE 0"), + PINCTRL_PIN(353, "PO TAP RET CLK"), + PINCTRL_PIN(354, "PI TAP CLK"), + PINCTRL_PIN(355, "PO EMIF 0 SD CS N"), + PINCTRL_PIN(356, "PO EMIF 0 SD CAS N"), + PINCTRL_PIN(357, "PO EMIF 0 SD WE N"), + PINCTRL_PIN(358, "P PAD VDDIO 1"), + PINCTRL_PIN(359, "P PAD VSSIO 1"), + PINCTRL_PIN(360, "P PAD GND 1"), + PINCTRL_PIN(361, "P PAD VDD 1"), + PINCTRL_PIN(362, "PO EMIF 0 SD CKE"), + PINCTRL_PIN(363, "PO EMIF 0 SD DQML"), + PINCTRL_PIN(364, "PO EMIF 0 SD DQMU"), + PINCTRL_PIN(365, "PO EMIF 0 SD RAS N"), + PINCTRL_PIN(366, "PIO EMIF 0 D15"), + PINCTRL_PIN(367, "PO EMIF 0 A15"), + PINCTRL_PIN(368, "PIO EMIF 0 D14"), + PINCTRL_PIN(369, "PO EMIF 0 A14"), + PINCTRL_PIN(370, "PIO EMIF 0 D13"), + PINCTRL_PIN(371, "PO EMIF 0 A13"), + PINCTRL_PIN(372, "P PAD VDDIO 2"), + PINCTRL_PIN(373, "P PAD VSSIO 2"), + PINCTRL_PIN(374, "P PAD GND 2"), + PINCTRL_PIN(375, "P PAD VDD 2"), + PINCTRL_PIN(376, "PIO EMIF 0 D12"), + PINCTRL_PIN(377, "PO EMIF 0 A12"), + PINCTRL_PIN(378, "PIO EMIF 0 D11"), + PINCTRL_PIN(379, "PO EMIF 0 A11"), + PINCTRL_PIN(380, "PIO EMIF 0 D10"), + PINCTRL_PIN(381, "PO EMIF 0 A10"), + PINCTRL_PIN(382, "PIO EMIF 0 D09"), + PINCTRL_PIN(383, "PO EMIF 0 A09"), + PINCTRL_PIN(384, "PIO EMIF 0 D08"), + PINCTRL_PIN(385, "PO EMIF 0 A08"), + PINCTRL_PIN(386, "PIO EMIF 0 D07"), + PINCTRL_PIN(387, "PO EMIF 0 A07"), + PINCTRL_PIN(388, "P PAD VDDIO 3"), + PINCTRL_PIN(389, "P PAD VSSIO 3"), + PINCTRL_PIN(390, "P PAD GND 3"), + PINCTRL_PIN(391, "P PAD VDD 3"), + PINCTRL_PIN(392, "PO EFUSE RDOUT1"), + PINCTRL_PIN(393, "PIO EMIF 0 D06"), + PINCTRL_PIN(394, "PO EMIF 0 A06"), + PINCTRL_PIN(395, "PIO EMIF 0 D05"), + PINCTRL_PIN(396, "PO EMIF 0 A05"), + PINCTRL_PIN(397, "PIO EMIF 0 D04"), + PINCTRL_PIN(398, "PO EMIF 0 A04"), + PINCTRL_PIN(399, "A PADS/A VDDCO1v82v5 GND 80U SF LIN VDDCO AF"), + PINCTRL_PIN(400, "PWR VDDCO AF"), + PINCTRL_PIN(401, "PWR EFUSE HV1"), + PINCTRL_PIN(402, "P PAD VSSIO 4"), + PINCTRL_PIN(403, "P PAD VDDIO 4"), + PINCTRL_PIN(404, "P PAD GND 4"), + PINCTRL_PIN(405, "P PAD VDD 4"), + PINCTRL_PIN(406, "PIO EMIF 0 D03"), + PINCTRL_PIN(407, "PO EMIF 0 A03"), + PINCTRL_PIN(408, "PWR EFUSE HV2"), + PINCTRL_PIN(409, "PWR EFUSE HV3"), + PINCTRL_PIN(410, "PIO EMIF 0 D02"), + PINCTRL_PIN(411, "PO EMIF 0 A02"), + PINCTRL_PIN(412, "PIO EMIF 0 D01"), + PINCTRL_PIN(413, "P PAD VDDIO 5"), + PINCTRL_PIN(414, "P PAD VSSIO 5"), + PINCTRL_PIN(415, "P PAD GND 5"), + PINCTRL_PIN(416, "P PAD VDD 5"), + PINCTRL_PIN(417, "PO EMIF 0 A01"), + PINCTRL_PIN(418, "PIO EMIF 0 D00"), + PINCTRL_PIN(419, "IF 0 SD CLK"), + PINCTRL_PIN(420, "APP SPI CLK"), + PINCTRL_PIN(421, "APP SPI DO"), + PINCTRL_PIN(422, "APP SPI DI"), + PINCTRL_PIN(423, "APP SPI CS0"), + PINCTRL_PIN(424, "APP SPI CS1"), + PINCTRL_PIN(425, "APP SPI CS2"), + PINCTRL_PIN(426, "PIO APP GPIO 10"), + PINCTRL_PIN(427, "P PAD VDDIO 41"), + PINCTRL_PIN(428, "P PAD VSSIO 41"), + PINCTRL_PIN(429, "P PAD GND 6"), + PINCTRL_PIN(430, "P PAD VDD 6"), + PINCTRL_PIN(431, "PIO ACC SDIO0 CMD"), + PINCTRL_PIN(432, "PIO ACC SDIO0 CK"), + PINCTRL_PIN(433, "PIO ACC SDIO0 D3"), + PINCTRL_PIN(434, "PIO ACC SDIO0 D2"), + PINCTRL_PIN(435, "PIO ACC SDIO0 D1"), + PINCTRL_PIN(436, "PIO ACC SDIO0 D0"), + PINCTRL_PIN(437, "PIO USB PU"), + PINCTRL_PIN(438, "PIO USB SP"), + PINCTRL_PIN(439, "PIO USB DAT VP"), + PINCTRL_PIN(440, "PIO USB SE0 VM"), + PINCTRL_PIN(441, "PIO USB OE"), + PINCTRL_PIN(442, "PIO USB SUSP"), + PINCTRL_PIN(443, "P PAD VSSIO 6"), + PINCTRL_PIN(444, "P PAD VDDIO 6"), + PINCTRL_PIN(445, "PIO USB PUEN"), + PINCTRL_PIN(446, "PIO ACC UART0 RX"), + PINCTRL_PIN(447, "PIO ACC UART0 TX"), + PINCTRL_PIN(448, "PIO ACC UART0 CTS"), + PINCTRL_PIN(449, "PIO ACC UART0 RTS"), + PINCTRL_PIN(450, "PIO ACC UART3 RX"), + PINCTRL_PIN(451, "PIO ACC UART3 TX"), + PINCTRL_PIN(452, "PIO ACC UART3 CTS"), + PINCTRL_PIN(453, "PIO ACC UART3 RTS"), + PINCTRL_PIN(454, "PIO ACC IRDA TX"), + PINCTRL_PIN(455, "P PAD VDDIO 7"), + PINCTRL_PIN(456, "P PAD VSSIO 7"), + PINCTRL_PIN(457, "P PAD GND 7"), + PINCTRL_PIN(458, "P PAD VDD 7"), + PINCTRL_PIN(459, "PIO ACC IRDA RX"), + PINCTRL_PIN(460, "PIO ACC PCM I2S CLK"), + PINCTRL_PIN(461, "PIO ACC PCM I2S WS"), + PINCTRL_PIN(462, "PIO ACC PCM I2S DATA A"), + PINCTRL_PIN(463, "PIO ACC PCM I2S DATA B"), + PINCTRL_PIN(464, "PO SIM CLK"), + PINCTRL_PIN(465, "PIO ACC IRDA SD"), + PINCTRL_PIN(466, "PIO SIM DATA"), +}; + +/** + * @dev: a pointer back to containing device + * @virtbase: the offset to the controller in virtual memory + */ +struct u300_pmx { + struct device *dev; + struct pinctrl_dev *pctl; + u32 phybase; + u32 physize; + void __iomem *virtbase; +}; + +/** + * u300_pmx_registers - the array of registers read/written for each pinmux + * shunt setting + */ +const u32 u300_pmx_registers[] = { + U300_SYSCON_PMC1LR, + U300_SYSCON_PMC1HR, + U300_SYSCON_PMC2R, + U300_SYSCON_PMC3R, + U300_SYSCON_PMC4R, +}; + +/** + * struct u300_pin_group - describes a U300 pin group + * @name: the name of this specific pin group + * @pins: an array of discrete physical pins used in this group, taken + * from the driver-local pin enumeration space + * @num_pins: the number of pins in this group array, i.e. the number of + * elements in .pins so we can iterate over that array + */ +struct u300_pin_group { + const char *name; + const unsigned int *pins; + const unsigned num_pins; +}; + +/** + * struct pmx_onmask - mask bits to enable/disable padmux + * @mask: mask bits to disable + * @val: mask bits to enable + * + * onmask lazy dog: + * onmask = { + * {"PMC1LR" mask, "PMC1LR" value}, + * {"PMC1HR" mask, "PMC1HR" value}, + * {"PMC2R" mask, "PMC2R" value}, + * {"PMC3R" mask, "PMC3R" value}, + * {"PMC4R" mask, "PMC4R" value} + * } + */ +struct u300_pmx_mask { + u16 mask; + u16 bits; +}; + +/* The chip power pins are VDD, GND, VDDIO and VSSIO */ +static const unsigned power_pins[] = { 0, 1, 3, 31, 46, 47, 49, 50, 61, 62, 63, + 64, 78, 79, 80, 81, 92, 93, 94, 95, 101, 102, 103, 104, 115, 116, 117, + 118, 130, 131, 132, 133, 145, 146, 147, 148, 159, 160, 172, 173, 174, + 175, 187, 188, 189, 190, 201, 202, 211, 212, 213, 214, 215, 218, 223, + 224, 225, 226, 231, 232, 237, 238, 239, 240, 245, 246, 251, 252, 256, + 257, 258, 259, 264, 265, 270, 271, 276, 277, 278, 279, 284, 285, 290, + 291, 295, 296, 299, 300, 301, 302, 303, 309, 310, 311, 312, 319, 320, + 321, 322, 329, 330, 331, 332, 341, 342, 343, 344, 358, 359, 360, 361, + 372, 373, 374, 375, 388, 389, 390, 391, 402, 403, 404, 405, 413, 414, + 415, 416, 427, 428, 429, 430, 443, 444, 455, 456, 457, 458 }; +static const unsigned emif0_pins[] = { 355, 356, 357, 362, 363, 364, 365, 366, + 367, 368, 369, 370, 371, 376, 377, 378, 379, 380, 381, 382, 383, 384, + 385, 386, 387, 393, 394, 395, 396, 397, 398, 406, 407, 410, 411, 412, + 417, 418 }; +static const unsigned emif1_pins[] = { 216, 217, 219, 220, 221, 222, 227, 228, + 229, 230, 233, 234, 235, 236, 241, 242, 243, 244, 247, 248, 249, 250, + 253, 254, 255, 260, 261, 262, 263, 266, 267, 268, 269, 272, 273, 274, + 275, 280, 281, 282, 283, 286, 287, 288, 289, 292, 293, 294, 297, 298, + 304, 305, 306, 307, 308, 313, 314, 315 }; +static const unsigned uart0_pins[] = { 134, 135, 136, 137 }; +static const unsigned mmc0_pins[] = { 166, 167, 168, 169, 170, 171, 176, 177 }; +static const unsigned spi0_pins[] = { 420, 421, 422, 423, 424, 425 }; + +static const struct u300_pmx_mask emif0_mask[] = { + {0, 0}, + {0, 0}, + {0, 0}, + {0, 0}, + {0, 0}, +}; + +static const struct u300_pmx_mask emif1_mask[] = { + /* + * This connects the SDRAM to CS2 and a NAND flash to + * CS0 on the EMIF. + */ + { + U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK | + U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK | + U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK | + U300_SYSCON_PMC1LR_EMIF_1_MASK, + U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM | + U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC | + U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF | + U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 + }, + {0, 0}, + {0, 0}, + {0, 0}, + {0, 0}, +}; + +static const struct u300_pmx_mask uart0_mask[] = { + {0, 0}, + { + U300_SYSCON_PMC1HR_APP_UART0_1_MASK | + U300_SYSCON_PMC1HR_APP_UART0_2_MASK, + U300_SYSCON_PMC1HR_APP_UART0_1_UART0 | + U300_SYSCON_PMC1HR_APP_UART0_2_UART0 + }, + {0, 0}, + {0, 0}, + {0, 0}, +}; + +static const struct u300_pmx_mask mmc0_mask[] = { + { U300_SYSCON_PMC1LR_MMCSD_MASK, U300_SYSCON_PMC1LR_MMCSD_MMCSD}, + {0, 0}, + {0, 0}, + {0, 0}, + { U300_SYSCON_PMC4R_APP_MISC_12_MASK, + U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO } +}; + +static const struct u300_pmx_mask spi0_mask[] = { + {0, 0}, + { + U300_SYSCON_PMC1HR_APP_SPI_2_MASK | + U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK | + U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK, + U300_SYSCON_PMC1HR_APP_SPI_2_SPI | + U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI | + U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI + }, + {0, 0}, + {0, 0}, + {0, 0} +}; + +static const struct u300_pin_group u300_pin_groups[] = { + { + .name = "powergrp", + .pins = power_pins, + .num_pins = ARRAY_SIZE(power_pins), + }, + { + .name = "emif0grp", + .pins = emif0_pins, + .num_pins = ARRAY_SIZE(emif0_pins), + }, + { + .name = "emif1grp", + .pins = emif1_pins, + .num_pins = ARRAY_SIZE(emif1_pins), + }, + { + .name = "uart0grp", + .pins = uart0_pins, + .num_pins = ARRAY_SIZE(uart0_pins), + }, + { + .name = "mmc0grp", + .pins = mmc0_pins, + .num_pins = ARRAY_SIZE(mmc0_pins), + }, + { + .name = "spi0grp", + .pins = spi0_pins, + .num_pins = ARRAY_SIZE(spi0_pins), + }, +}; + +static int u300_list_groups(struct pinctrl_dev *pctldev, unsigned selector) +{ + if (selector >= ARRAY_SIZE(u300_pin_groups)) + return -EINVAL; + return 0; +} + +static const char *u300_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + if (selector >= ARRAY_SIZE(u300_pin_groups)) + return NULL; + return u300_pin_groups[selector].name; +} + +static int u300_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector, + unsigned ** const pins, + unsigned * const num_pins) +{ + if (selector >= ARRAY_SIZE(u300_pin_groups)) + return -EINVAL; + *pins = (unsigned *) u300_pin_groups[selector].pins; + *num_pins = u300_pin_groups[selector].num_pins; + return 0; +} + +static void u300_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, + unsigned offset) +{ + seq_printf(s, " " DRIVER_NAME); +} + +static struct pinctrl_ops u300_pctrl_ops = { + .list_groups = u300_list_groups, + .get_group_name = u300_get_group_name, + .get_group_pins = u300_get_group_pins, + .pin_dbg_show = u300_pin_dbg_show, +}; + +/* + * Here we define the available functions and their corresponding pin groups + */ + +/** + * struct u300_pmx_func - describes U300 pinmux functions + * @name: the name of this specific function + * @groups: corresponding pin groups + * @onmask: bits to set to enable this when doing pin muxing + */ +struct u300_pmx_func { + const char *name; + const char * const *groups; + const unsigned num_groups; + const struct u300_pmx_mask *mask; +}; + +static const char * const powergrps[] = { "powergrp" }; +static const char * const emif0grps[] = { "emif0grp" }; +static const char * const emif1grps[] = { "emif1grp" }; +static const char * const uart0grps[] = { "uart0grp" }; +static const char * const mmc0grps[] = { "mmc0grp" }; +static const char * const spi0grps[] = { "spi0grp" }; + +static const struct u300_pmx_func u300_pmx_functions[] = { + { + .name = "power", + .groups = powergrps, + .num_groups = ARRAY_SIZE(powergrps), + /* Mask is N/A */ + }, + { + .name = "emif0", + .groups = emif0grps, + .num_groups = ARRAY_SIZE(emif0grps), + .mask = emif0_mask, + }, + { + .name = "emif1", + .groups = emif1grps, + .num_groups = ARRAY_SIZE(emif1grps), + .mask = emif1_mask, + }, + { + .name = "uart0", + .groups = uart0grps, + .num_groups = ARRAY_SIZE(uart0grps), + .mask = uart0_mask, + }, + { + .name = "mmc0", + .groups = mmc0grps, + .num_groups = ARRAY_SIZE(mmc0grps), + .mask = mmc0_mask, + }, + { + .name = "spi0", + .groups = spi0grps, + .num_groups = ARRAY_SIZE(spi0grps), + .mask = spi0_mask, + }, +}; + +static void u300_pmx_endisable(struct u300_pmx *upmx, unsigned selector, + bool enable) +{ + u16 regval, val, mask; + int i; + + for (i = 0; i < ARRAY_SIZE(u300_pmx_registers); i++) { + if (enable) + val = u300_pmx_functions[selector].mask->bits; + else + val = 0; + + mask = u300_pmx_functions[selector].mask->mask; + if (mask != 0) { + regval = readw(upmx->virtbase + u300_pmx_registers[i]); + regval &= ~mask; + regval |= val; + writew(regval, upmx->virtbase + u300_pmx_registers[i]); + } + } +} + +static int u300_pmx_enable(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group) +{ + struct u300_pmx *upmx; + + /* There is nothing to do with the power pins */ + if (selector == 0) + return 0; + + upmx = pctldev_get_drvdata(pctldev); + u300_pmx_endisable(upmx, selector, true); + + return 0; +} + +static void u300_pmx_disable(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group) +{ + struct u300_pmx *upmx; + + /* There is nothing to do with the power pins */ + if (selector == 0) + return; + + upmx = pctldev_get_drvdata(pctldev); + u300_pmx_endisable(upmx, selector, false); +} + +static int u300_pmx_list_funcs(struct pinctrl_dev *pctldev, unsigned selector) +{ + if (selector >= ARRAY_SIZE(u300_pmx_functions)) + return -EINVAL; + return 0; +} + +static const char *u300_pmx_get_func_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + return u300_pmx_functions[selector].name; +} + +static int u300_pmx_get_groups(struct pinctrl_dev *pctldev, unsigned selector, + const char * const **groups, + unsigned * const num_groups) +{ + *groups = u300_pmx_functions[selector].groups; + *num_groups = u300_pmx_functions[selector].num_groups; + return 0; +} + +static struct pinmux_ops u300_pmx_ops = { + .list_functions = u300_pmx_list_funcs, + .get_function_name = u300_pmx_get_func_name, + .get_function_groups = u300_pmx_get_groups, + .enable = u300_pmx_enable, + .disable = u300_pmx_disable, +}; + +/* + * FIXME: this will be set to sane values as this driver engulfs + * drivers/gpio/gpio-u300.c and we really know this stuff. + */ +static struct pinctrl_gpio_range u300_gpio_range = { + .name = "COH901*", + .id = 0, + .base = 0, + .npins = 64, +}; + +static struct pinctrl_desc u300_pmx_desc = { + .name = DRIVER_NAME, + .pins = u300_pads, + .npins = ARRAY_SIZE(u300_pads), + .maxpin = U300_NUM_PADS-1, + .pctlops = &u300_pctrl_ops, + .pmxops = &u300_pmx_ops, + .owner = THIS_MODULE, +}; + +static int __init u300_pmx_probe(struct platform_device *pdev) +{ + int ret; + struct u300_pmx *upmx; + struct resource *res; + + /* Create state holders etc for this driver */ + upmx = devm_kzalloc(&pdev->dev, sizeof(*upmx), GFP_KERNEL); + if (!upmx) + return -ENOMEM; + + upmx->dev = &pdev->dev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + ret = -ENOENT; + goto out_no_resource; + } + upmx->phybase = res->start; + upmx->physize = resource_size(res); + + if (request_mem_region(upmx->phybase, upmx->physize, + DRIVER_NAME) == NULL) { + ret = -EBUSY; + goto out_no_memregion; + } + + upmx->virtbase = ioremap(upmx->phybase, upmx->physize); + if (!upmx->virtbase) { + ret = -ENOMEM; + goto out_no_remap; + } + + upmx->pctl = pinctrl_register(&u300_pmx_desc, &pdev->dev, upmx); + if (IS_ERR(upmx->pctl)) { + dev_err(&pdev->dev, "could not register U300 pinmux driver\n"); + ret = PTR_ERR(upmx->pctl); + goto out_no_pmx; + } + + /* We will handle a range of GPIO pins */ + pinctrl_add_gpio_range(upmx->pctl, &u300_gpio_range); + + platform_set_drvdata(pdev, upmx); + + dev_info(&pdev->dev, "initialized U300 pinmux driver\n"); + + return 0; + +out_no_pmx: + iounmap(upmx->virtbase); +out_no_remap: + platform_set_drvdata(pdev, NULL); +out_no_memregion: + release_mem_region(upmx->phybase, upmx->physize); +out_no_resource: + devm_kfree(&pdev->dev, upmx); + return ret; +} + +static int __exit u300_pmx_remove(struct platform_device *pdev) +{ + struct u300_pmx *upmx = platform_get_drvdata(pdev); + + pinctrl_remove_gpio_range(upmx->pctl, &u300_gpio_range); + pinctrl_unregister(upmx->pctl); + iounmap(upmx->virtbase); + release_mem_region(upmx->phybase, upmx->physize); + platform_set_drvdata(pdev, NULL); + devm_kfree(&pdev->dev, upmx); + + return 0; +} + +static struct platform_driver u300_pmx_driver = { + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + }, + .remove = __exit_p(u300_pmx_remove), +}; + +static int __init u300_pmx_init(void) +{ + return platform_driver_probe(&u300_pmx_driver, u300_pmx_probe); +} +arch_initcall(u300_pmx_init); + +static void __exit u300_pmx_exit(void) +{ + platform_driver_unregister(&u300_pmx_driver); +} +module_exit(u300_pmx_exit); + +MODULE_AUTHOR("Linus Walleij <linus.walleij(a)linaro.org>"); +MODULE_DESCRIPTION("U300 pin control driver"); +MODULE_LICENSE("GPL v2"); -- 1.7.3.2

13 years, 10 months

[PATCH 2/2] pinmux: add a driver for the U300 pinmux

by Linus Walleij

From: Linus Walleij <linus.walleij(a)linaro.org> This adds a driver for the U300 pinmux portions of the system controller "SYSCON". It also serves as an example of how to use the pinmux subsystem. This driver also houses the platform data for the only supported platform. This deletes the old U300 driver in arch/arm/mach-u300 and replace it with a driver using the new subsystem. The new driver is considerably fatter than the old one, but it also registers all 467 pins of the system and adds the power and EMIF pin groups and corresponding functions. The idea is to use this driver as a a reference for other implementation so it needs to be as complete and verbose as possible. Signed-off-by: Linus Walleij <linus.walleij(a)linaro.org> --- ChangeLog v7->v9: - Use devm_kzalloc()/devm_kfree() to allocate memory - Merge the pinmux-u300.h header file into the the driver file. --- arch/arm/mach-u300/Kconfig | 2 + arch/arm/mach-u300/Makefile | 2 +- arch/arm/mach-u300/core.c | 84 +++- arch/arm/mach-u300/include/mach/syscon.h | 136 ---- arch/arm/mach-u300/mmc.c | 16 - arch/arm/mach-u300/padmux.c | 367 ---------- arch/arm/mach-u300/padmux.h | 39 - arch/arm/mach-u300/spi.c | 20 - drivers/pinctrl/Kconfig | 7 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinmux-u300.c | 1148 ++++++++++++++++++++++++++++++ 11 files changed, 1241 insertions(+), 581 deletions(-) delete mode 100644 arch/arm/mach-u300/padmux.c delete mode 100644 arch/arm/mach-u300/padmux.h create mode 100644 drivers/pinctrl/pinmux-u300.c diff --git a/arch/arm/mach-u300/Kconfig b/arch/arm/mach-u300/Kconfig index 32a7b0f..449fd6a 100644 --- a/arch/arm/mach-u300/Kconfig +++ b/arch/arm/mach-u300/Kconfig @@ -6,6 +6,8 @@ comment "ST-Ericsson Mobile Platform Products" config MACH_U300 bool "U300" + select PINCTRL + select PINMUX_U300 comment "ST-Ericsson U300/U330/U335/U365 Feature Selections" diff --git a/arch/arm/mach-u300/Makefile b/arch/arm/mach-u300/Makefile index 8fd354a..2855381 100644 --- a/arch/arm/mach-u300/Makefile +++ b/arch/arm/mach-u300/Makefile @@ -2,7 +2,7 @@ # Makefile for the linux kernel, U300 machine. # -obj-y := core.o clock.o timer.o padmux.o +obj-y := core.o clock.o timer.o obj-m := obj-n := obj- := diff --git a/arch/arm/mach-u300/core.c b/arch/arm/mach-u300/core.c index 399c89f..2f5929b 100644 --- a/arch/arm/mach-u300/core.c +++ b/arch/arm/mach-u300/core.c @@ -25,6 +25,8 @@ #include <linux/err.h> #include <linux/mtd/nand.h> #include <linux/mtd/fsmc.h> +#include <linux/pinctrl/machine.h> +#include <linux/pinctrl/pinmux.h> #include <asm/types.h> #include <asm/setup.h> @@ -1535,6 +1537,14 @@ static struct coh901318_platform coh901318_platform = { .max_channels = U300_DMA_CHANNELS, }; +static struct resource pinmux_resources[] = { + { + .start = U300_SYSCON_BASE, + .end = U300_SYSCON_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + static struct platform_device wdog_device = { .name = "coh901327_wdog", .id = -1, @@ -1630,6 +1640,72 @@ static struct platform_device dma_device = { }, }; +static struct platform_device pinmux_device = { + .name = "pinmux-u300", + .id = -1, + .num_resources = ARRAY_SIZE(pinmux_resources), + .resource = pinmux_resources, +}; + +/* Pinmux settings */ +static struct pinmux_map u300_pinmux_map[] = { + /* anonymous maps for chip power and EMIFs */ + PINMUX_MAP_PRIMARY_SYS_HOG("POWER", "power"), + PINMUX_MAP_PRIMARY_SYS_HOG("EMIF0", "emif0"), + PINMUX_MAP_PRIMARY_SYS_HOG("EMIF1", "emif1"), + /* per-device maps for MMC/SD, SPI and UART */ + PINMUX_MAP_PRIMARY("MMCSD", "mmc0", "mmci"), + PINMUX_MAP_PRIMARY("SPI", "spi0", "pl022"), + PINMUX_MAP_PRIMARY("UART0", "uart0", "uart0"), +}; + +struct u300_mux_hog { + const char *name; + struct device *dev; + struct pinmux *pmx; +}; + +static struct u300_mux_hog u300_mux_hogs[] = { + { + .name = "uart0", + .dev = &uart0_device.dev, + }, + { + .name = "spi0", + .dev = &pl022_device.dev, + }, + { + .name = "mmc0", + .dev = &mmcsd_device.dev, + }, +}; + +static int __init u300_pinmux_fetch(void) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(u300_mux_hogs); i++) { + struct pinmux *pmx; + int ret; + + pmx = pinmux_get(u300_mux_hogs[i].dev, NULL); + if (IS_ERR(pmx)) { + pr_err("u300: could not get pinmux hog %s\n", + u300_mux_hogs[i].name); + continue; + } + ret = pinmux_enable(pmx); + if (ret) { + pr_err("u300: could enable pinmux hog %s\n", + u300_mux_hogs[i].name); + continue; + } + u300_mux_hogs[i].pmx = pmx; + } + return 0; +} +subsys_initcall(u300_pinmux_fetch); + /* * Notice that AMBA devices are initialized before platform devices. * @@ -1643,10 +1719,10 @@ static struct platform_device *platform_devs[] __initdata = { &gpio_device, &nand_device, &wdog_device, - &ave_device + &ave_device, + &pinmux_device, }; - /* * Interrupts: the U300 platforms have two pl190 ARM PrimeCells connected * together so some interrupts are connected to the first one and some @@ -1828,6 +1904,10 @@ void __init u300_init_devices(void) u300_assign_physmem(); + /* Initialize pinmuxing */ + pinmux_register_mappings(u300_pinmux_map, + ARRAY_SIZE(u300_pinmux_map)); + /* Register subdevices on the I2C buses */ u300_i2c_register_board_devices(); diff --git a/arch/arm/mach-u300/include/mach/syscon.h b/arch/arm/mach-u300/include/mach/syscon.h index 7444f5c..6e84f07 100644 --- a/arch/arm/mach-u300/include/mach/syscon.h +++ b/arch/arm/mach-u300/include/mach/syscon.h @@ -234,91 +234,6 @@ #define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE (0x0004) #define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE (0x0002) #define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE (0x0001) -/* PAD MUX Control register 1 (LOW) 16bit (R/W) */ -#define U300_SYSCON_PMC1LR (0x007C) -#define U300_SYSCON_PMC1LR_MASK (0xFFFF) -#define U300_SYSCON_PMC1LR_CDI_MASK (0xC000) -#define U300_SYSCON_PMC1LR_CDI_CDI (0x0000) -#define U300_SYSCON_PMC1LR_CDI_EMIF (0x4000) -#ifdef CONFIG_MACH_U300_BS335 -#define U300_SYSCON_PMC1LR_CDI_CDI2 (0x8000) -#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO (0xC000) -#elif CONFIG_MACH_U300_BS365 -#define U300_SYSCON_PMC1LR_CDI_GPIO (0x8000) -#define U300_SYSCON_PMC1LR_CDI_WCDMA (0xC000) -#endif -#define U300_SYSCON_PMC1LR_PDI_MASK (0x3000) -#define U300_SYSCON_PMC1LR_PDI_PDI (0x0000) -#define U300_SYSCON_PMC1LR_PDI_EGG (0x1000) -#define U300_SYSCON_PMC1LR_PDI_WCDMA (0x3000) -#define U300_SYSCON_PMC1LR_MMCSD_MASK (0x0C00) -#define U300_SYSCON_PMC1LR_MMCSD_MMCSD (0x0000) -#define U300_SYSCON_PMC1LR_MMCSD_MSPRO (0x0400) -#define U300_SYSCON_PMC1LR_MMCSD_DSP (0x0800) -#define U300_SYSCON_PMC1LR_MMCSD_WCDMA (0x0C00) -#define U300_SYSCON_PMC1LR_ETM_MASK (0x0300) -#define U300_SYSCON_PMC1LR_ETM_ACC (0x0000) -#define U300_SYSCON_PMC1LR_ETM_APP (0x0100) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK (0x00C0) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF (0x0040) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM (0x0080) -#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB (0x00C0) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK (0x0030) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF (0x0010) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM (0x0020) -#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI (0x0030) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK (0x000C) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF (0x0004) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM (0x0008) -#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI (0x000C) -#define U300_SYSCON_PMC1LR_EMIF_1_MASK (0x0003) -#define U300_SYSCON_PMC1LR_EMIF_1_STATIC (0x0000) -#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 (0x0001) -#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1 (0x0002) -#define U300_SYSCON_PMC1LR_EMIF_1 (0x0003) -/* PAD MUX Control register 2 (HIGH) 16bit (R/W) */ -#define U300_SYSCON_PMC1HR (0x007E) -#define U300_SYSCON_PMC1HR_MASK (0xFFFF) -#define U300_SYSCON_PMC1HR_MISC_2_MASK (0xC000) -#define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_MISC_2_MSPRO (0x4000) -#define U300_SYSCON_PMC1HR_MISC_2_DSP (0x8000) -#define U300_SYSCON_PMC1HR_MISC_2_AAIF (0xC000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK (0x3000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF (0x1000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP (0x2000) -#define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF (0x3000) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK (0x0C00) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC (0x0400) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP (0x0800) -#define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF (0x0C00) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK (0x0300) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI (0x0100) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF (0x0300) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK (0x00C0) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI (0x0040) -#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF (0x00C0) -#define U300_SYSCON_PMC1HR_APP_SPI_2_MASK (0x0030) -#define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_SPI_2_SPI (0x0010) -#define U300_SYSCON_PMC1HR_APP_SPI_2_DSP (0x0020) -#define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF (0x0030) -#define U300_SYSCON_PMC1HR_APP_UART0_2_MASK (0x000C) -#define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_UART0_2_UART0 (0x0004) -#define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS (0x0008) -#define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF (0x000C) -#define U300_SYSCON_PMC1HR_APP_UART0_1_MASK (0x0003) -#define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC1HR_APP_UART0_1_UART0 (0x0001) -#define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF (0x0003) /* Step one for killing the applications system 16bit (-/W) */ #define U300_SYSCON_KA1R (0x0080) #define U300_SYSCON_KA1R_MASK (0xFFFF) @@ -357,57 +272,6 @@ #define U300_SYSCON_PUCR_EMIF_1_16BIT_PU_ENABLE (0x0080) #define U300_SYSCON_PUCR_EMIF_1_8BIT_PU_ENABLE (0x0040) #define U300_SYSCON_PUCR_KEY_IN_PU_EN_MASK (0x003F) -/* Padmux 2 control */ -#define U300_SYSCON_PMC2R (0x100) -#define U300_SYSCON_PMC2R_APP_MISC_0_MASK (0x00C0) -#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM (0x0040) -#define U300_SYSCON_PMC2R_APP_MISC_0_MMC (0x0080) -#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 (0x00C0) -#define U300_SYSCON_PMC2R_APP_MISC_1_MASK (0x0300) -#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM (0x0100) -#define U300_SYSCON_PMC2R_APP_MISC_1_MMC (0x0200) -#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 (0x0300) -#define U300_SYSCON_PMC2R_APP_MISC_2_MASK (0x0C00) -#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM (0x0400) -#define U300_SYSCON_PMC2R_APP_MISC_2_MMC (0x0800) -#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 (0x0C00) -#define U300_SYSCON_PMC2R_APP_MISC_3_MASK (0x3000) -#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM (0x1000) -#define U300_SYSCON_PMC2R_APP_MISC_3_MMC (0x2000) -#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 (0x3000) -#define U300_SYSCON_PMC2R_APP_MISC_4_MASK (0xC000) -#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO (0x0000) -#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM (0x4000) -#define U300_SYSCON_PMC2R_APP_MISC_4_MMC (0x8000) -#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO (0xC000) -/* TODO: More SYSCON registers missing */ -#define U300_SYSCON_PMC3R (0x10c) -#define U300_SYSCON_PMC3R_APP_MISC_11_MASK (0xc000) -#define U300_SYSCON_PMC3R_APP_MISC_11_SPI (0x4000) -#define U300_SYSCON_PMC3R_APP_MISC_10_MASK (0x3000) -#define U300_SYSCON_PMC3R_APP_MISC_10_SPI (0x1000) -/* TODO: Missing other configs */ -#define U300_SYSCON_PMC4R (0x168) -#define U300_SYSCON_PMC4R_APP_MISC_12_MASK (0x0003) -#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_13_MASK (0x000C) -#define U300_SYSCON_PMC4R_APP_MISC_13_CDI (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA (0x0004) -#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 (0x0008) -#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO (0x000C) -#define U300_SYSCON_PMC4R_APP_MISC_14_MASK (0x0030) -#define U300_SYSCON_PMC4R_APP_MISC_14_CDI (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA (0x0010) -#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 (0x0020) -#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO (0x0030) -#define U300_SYSCON_PMC4R_APP_MISC_16_MASK (0x0300) -#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 (0x0000) -#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS (0x0100) -#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N (0x0200) /* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */ #define U300_SYSCON_S0CCR (0x120) #define U300_SYSCON_S0CCR_FIELD_MASK (0x43FF) diff --git a/arch/arm/mach-u300/mmc.c b/arch/arm/mach-u300/mmc.c index 677ccef..d5e4a98 100644 --- a/arch/arm/mach-u300/mmc.c +++ b/arch/arm/mach-u300/mmc.c @@ -21,7 +21,6 @@ #include <mach/dma_channels.h> #include "mmc.h" -#include "padmux.h" static struct mmci_platform_data mmc0_plat_data = { /* @@ -45,24 +44,9 @@ static struct mmci_platform_data mmc0_plat_data = { int __devinit mmc_init(struct amba_device *adev) { struct device *mmcsd_device = &adev->dev; - struct pmx *pmx; int ret = 0; mmcsd_device->platform_data = &mmc0_plat_data; - /* - * Setup padmuxing for MMC. Since this must always be - * compiled into the kernel, pmx is never released. - */ - pmx = pmx_get(mmcsd_device, U300_APP_PMX_MMC_SETTING); - - if (IS_ERR(pmx)) - pr_warning("Could not get padmux handle\n"); - else { - ret = pmx_activate(mmcsd_device, pmx); - if (IS_ERR_VALUE(ret)) - pr_warning("Could not activate padmuxing\n"); - } - return ret; } diff --git a/arch/arm/mach-u300/padmux.c b/arch/arm/mach-u300/padmux.c deleted file mode 100644 index 4c93c6c..0000000 --- a/arch/arm/mach-u300/padmux.c +++ /dev/null @@ -1,367 +0,0 @@ -/* - * - * arch/arm/mach-u300/padmux.c - * - * - * Copyright (C) 2009 ST-Ericsson AB - * License terms: GNU General Public License (GPL) version 2 - * U300 PADMUX functions - * Author: Martin Persson <martin.persson(a)stericsson.com> - */ - -#include <linux/module.h> -#include <linux/kernel.h> -#include <linux/device.h> -#include <linux/err.h> -#include <linux/errno.h> -#include <linux/io.h> -#include <linux/mutex.h> -#include <linux/string.h> -#include <linux/bug.h> -#include <linux/debugfs.h> -#include <linux/seq_file.h> -#include <mach/u300-regs.h> -#include <mach/syscon.h> -#include "padmux.h" - -static DEFINE_MUTEX(pmx_mutex); - -const u32 pmx_registers[] = { - (U300_SYSCON_VBASE + U300_SYSCON_PMC1LR), - (U300_SYSCON_VBASE + U300_SYSCON_PMC1HR), - (U300_SYSCON_VBASE + U300_SYSCON_PMC2R), - (U300_SYSCON_VBASE + U300_SYSCON_PMC3R), - (U300_SYSCON_VBASE + U300_SYSCON_PMC4R) -}; - -/* High level functionality */ - -/* Lazy dog: - * onmask = { - * {"PMC1LR" mask, "PMC1LR" value}, - * {"PMC1HR" mask, "PMC1HR" value}, - * {"PMC2R" mask, "PMC2R" value}, - * {"PMC3R" mask, "PMC3R" value}, - * {"PMC4R" mask, "PMC4R" value} - * } - */ -static struct pmx mmc_setting = { - .setting = U300_APP_PMX_MMC_SETTING, - .default_on = false, - .activated = false, - .name = "MMC", - .onmask = { - {U300_SYSCON_PMC1LR_MMCSD_MASK, - U300_SYSCON_PMC1LR_MMCSD_MMCSD}, - {0, 0}, - {0, 0}, - {0, 0}, - {U300_SYSCON_PMC4R_APP_MISC_12_MASK, - U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO} - }, -}; - -static struct pmx spi_setting = { - .setting = U300_APP_PMX_SPI_SETTING, - .default_on = false, - .activated = false, - .name = "SPI", - .onmask = {{0, 0}, - {U300_SYSCON_PMC1HR_APP_SPI_2_MASK | - U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK | - U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK, - U300_SYSCON_PMC1HR_APP_SPI_2_SPI | - U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI | - U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI}, - {0, 0}, - {0, 0}, - {0, 0} - }, -}; - -/* Available padmux settings */ -static struct pmx *pmx_settings[] = { - &mmc_setting, - &spi_setting, -}; - -static void update_registers(struct pmx *pmx, bool activate) -{ - u16 regval, val, mask; - int i; - - for (i = 0; i < ARRAY_SIZE(pmx_registers); i++) { - if (activate) - val = pmx->onmask[i].val; - else - val = 0; - - mask = pmx->onmask[i].mask; - if (mask != 0) { - regval = readw(pmx_registers[i]); - regval &= ~mask; - regval |= val; - writew(regval, pmx_registers[i]); - } - } -} - -struct pmx *pmx_get(struct device *dev, enum pmx_settings setting) -{ - int i; - struct pmx *pmx = ERR_PTR(-ENOENT); - - if (dev == NULL) - return ERR_PTR(-EINVAL); - - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (setting == pmx_settings[i]->setting) { - - if (pmx_settings[i]->dev != NULL) { - WARN(1, "padmux: required setting " - "in use by another consumer\n"); - } else { - pmx = pmx_settings[i]; - pmx->dev = dev; - dev_dbg(dev, "padmux: setting nr %d is now " - "bound to %s and ready to use\n", - setting, dev_name(dev)); - break; - } - } - } - mutex_unlock(&pmx_mutex); - - return pmx; -} -EXPORT_SYMBOL(pmx_get); - -int pmx_put(struct device *dev, struct pmx *pmx) -{ - int i; - int ret = -ENOENT; - - if (pmx == NULL || dev == NULL) - return -EINVAL; - - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (pmx->setting == pmx_settings[i]->setting) { - - if (dev != pmx->dev) { - WARN(1, "padmux: cannot release handle as " - "it is bound to another consumer\n"); - ret = -EINVAL; - break; - } else { - pmx_settings[i]->dev = NULL; - ret = 0; - break; - } - } - } - mutex_unlock(&pmx_mutex); - - return ret; -} -EXPORT_SYMBOL(pmx_put); - -int pmx_activate(struct device *dev, struct pmx *pmx) -{ - int i, j, ret; - ret = 0; - - if (pmx == NULL || dev == NULL) - return -EINVAL; - - mutex_lock(&pmx_mutex); - - /* Make sure the required bits are not used */ - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (pmx_settings[i]->dev == NULL || pmx_settings[i] == pmx) - continue; - - for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) { - - if (pmx_settings[i]->onmask[j].mask & pmx-> - onmask[j].mask) { - /* More than one entry on the same bits */ - WARN(1, "padmux: cannot activate " - "setting. Bit conflict with " - "an active setting\n"); - - ret = -EUSERS; - goto exit; - } - } - } - update_registers(pmx, true); - pmx->activated = true; - dev_dbg(dev, "padmux: setting nr %d is activated\n", - pmx->setting); - -exit: - mutex_unlock(&pmx_mutex); - return ret; -} -EXPORT_SYMBOL(pmx_activate); - -int pmx_deactivate(struct device *dev, struct pmx *pmx) -{ - int i; - int ret = -ENOENT; - - if (pmx == NULL || dev == NULL) - return -EINVAL; - - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (pmx_settings[i]->dev == NULL) - continue; - - if (pmx->setting == pmx_settings[i]->setting) { - - if (dev != pmx->dev) { - WARN(1, "padmux: cannot deactivate " - "pmx setting as it was activated " - "by another consumer\n"); - - ret = -EBUSY; - continue; - } else { - update_registers(pmx, false); - pmx_settings[i]->dev = NULL; - pmx->activated = false; - ret = 0; - dev_dbg(dev, "padmux: setting nr %d is deactivated", - pmx->setting); - break; - } - } - } - mutex_unlock(&pmx_mutex); - - return ret; -} -EXPORT_SYMBOL(pmx_deactivate); - -/* - * For internal use only. If it is to be exported, - * it should be reentrant. Notice that pmx_activate - * (i.e. runtime settings) always override default settings. - */ -static int pmx_set_default(void) -{ - /* Used to identify several entries on the same bits */ - u16 modbits[ARRAY_SIZE(pmx_registers)]; - - int i, j; - - memset(modbits, 0, ARRAY_SIZE(pmx_registers) * sizeof(u16)); - - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - - if (!pmx_settings[i]->default_on) - continue; - - for (j = 0; j < ARRAY_SIZE(pmx_registers); j++) { - - /* Make sure there is only one entry on the same bits */ - if (modbits[j] & pmx_settings[i]->onmask[j].mask) { - BUG(); - return -EUSERS; - } - modbits[j] |= pmx_settings[i]->onmask[j].mask; - } - update_registers(pmx_settings[i], true); - } - return 0; -} - -#if (defined(CONFIG_DEBUG_FS) && defined(CONFIG_U300_DEBUG)) -static int pmx_show(struct seq_file *s, void *data) -{ - int i; - seq_printf(s, "-------------------------------------------------\n"); - seq_printf(s, "SETTING BOUND TO DEVICE STATE\n"); - seq_printf(s, "-------------------------------------------------\n"); - mutex_lock(&pmx_mutex); - for (i = 0; i < ARRAY_SIZE(pmx_settings); i++) { - /* Format pmx and device name nicely */ - char cdp[33]; - int chars; - - chars = snprintf(&cdp[0], 17, "%s", pmx_settings[i]->name); - while (chars < 16) { - cdp[chars] = ' '; - chars++; - } - chars = snprintf(&cdp[16], 17, "%s", pmx_settings[i]->dev ? - dev_name(pmx_settings[i]->dev) : "N/A"); - while (chars < 16) { - cdp[chars+16] = ' '; - chars++; - } - cdp[32] = '\0'; - - seq_printf(s, - "%s\t%s\n", - &cdp[0], - pmx_settings[i]->activated ? - "ACTIVATED" : "DEACTIVATED" - ); - - } - mutex_unlock(&pmx_mutex); - return 0; -} - -static int pmx_open(struct inode *inode, struct file *file) -{ - return single_open(file, pmx_show, NULL); -} - -static const struct file_operations pmx_operations = { - .owner = THIS_MODULE, - .open = pmx_open, - .read = seq_read, - .llseek = seq_lseek, - .release = single_release, -}; - -static int __init init_pmx_read_debugfs(void) -{ - /* Expose a simple debugfs interface to view pmx settings */ - (void) debugfs_create_file("padmux", S_IFREG | S_IRUGO, - NULL, NULL, - &pmx_operations); - return 0; -} - -/* - * This needs to come in after the core_initcall(), - * because debugfs is not available until - * the subsystems come up. - */ -module_init(init_pmx_read_debugfs); -#endif - -static int __init pmx_init(void) -{ - int ret; - - ret = pmx_set_default(); - - if (IS_ERR_VALUE(ret)) - pr_crit("padmux: default settings could not be set\n"); - - return 0; -} - -/* Should be initialized before consumers */ -core_initcall(pmx_init); diff --git a/arch/arm/mach-u300/padmux.h b/arch/arm/mach-u300/padmux.h deleted file mode 100644 index 6e8b860..0000000 --- a/arch/arm/mach-u300/padmux.h +++ /dev/null @@ -1,39 +0,0 @@ -/* - * - * arch/arm/mach-u300/padmux.h - * - * - * Copyright (C) 2009 ST-Ericsson AB - * License terms: GNU General Public License (GPL) version 2 - * U300 PADMUX API - * Author: Martin Persson <martin.persson(a)stericsson.com> - */ - -#ifndef __MACH_U300_PADMUX_H -#define __MACH_U300_PADMUX_H - -enum pmx_settings { - U300_APP_PMX_MMC_SETTING, - U300_APP_PMX_SPI_SETTING -}; - -struct pmx_onmask { - u16 mask; /* Mask bits */ - u16 val; /* Value when active */ -}; - -struct pmx { - struct device *dev; - enum pmx_settings setting; - char *name; - bool activated; - bool default_on; - struct pmx_onmask onmask[]; -}; - -struct pmx *pmx_get(struct device *dev, enum pmx_settings setting); -int pmx_put(struct device *dev, struct pmx *pmx); -int pmx_activate(struct device *dev, struct pmx *pmx); -int pmx_deactivate(struct device *dev, struct pmx *pmx); - -#endif diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c index 7b597e2..a1affac 100644 --- a/arch/arm/mach-u300/spi.c +++ b/arch/arm/mach-u300/spi.c @@ -14,8 +14,6 @@ #include <mach/coh901318.h> #include <mach/dma_channels.h> -#include "padmux.h" - /* * The following is for the actual devices on the SSP/SPI bus */ @@ -95,25 +93,7 @@ static struct pl022_ssp_controller ssp_platform_data = { void __init u300_spi_init(struct amba_device *adev) { - struct pmx *pmx; - adev->dev.platform_data = &ssp_platform_data; - /* - * Setup padmuxing for SPI. Since this must always be - * compiled into the kernel, pmx is never released. - */ - pmx = pmx_get(&adev->dev, U300_APP_PMX_SPI_SETTING); - - if (IS_ERR(pmx)) - dev_warn(&adev->dev, "Could not get padmux handle\n"); - else { - int ret; - - ret = pmx_activate(&adev->dev, pmx); - if (IS_ERR_VALUE(ret)) - dev_warn(&adev->dev, "Could not activate padmuxing\n"); - } - } void __init u300_spi_register_board_devices(void) diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig index 7fa0fe0..8b3d081 100644 --- a/drivers/pinctrl/Kconfig +++ b/drivers/pinctrl/Kconfig @@ -26,4 +26,11 @@ config DEBUG_PINCTRL help Say Y here to add some extra checks and diagnostics to PINCTRL calls. +config PINMUX_U300 + bool "U300 pinmux driver" + depends on ARCH_U300 + select PINMUX + help + Say Y here to enable the U300 pinmux driver + endif diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile index 596ce9f..63d4241 100644 --- a/drivers/pinctrl/Makefile +++ b/drivers/pinctrl/Makefile @@ -4,3 +4,4 @@ ccflags-$(CONFIG_DEBUG_PINMUX) += -DDEBUG obj-$(CONFIG_PINCTRL) += core.o obj-$(CONFIG_PINMUX) += pinmux.o +obj-$(CONFIG_PINMUX_U300) += pinmux-u300.o diff --git a/drivers/pinctrl/pinmux-u300.c b/drivers/pinctrl/pinmux-u300.c new file mode 100644 index 0000000..a5c3385 --- /dev/null +++ b/drivers/pinctrl/pinmux-u300.c @@ -0,0 +1,1148 @@ +/* + * Driver for the U300 pin controller + * + * Based on the original U300 padmux functions + * Copyright (C) 2009-2011 ST-Ericsson AB + * Author: Martin Persson <martin.persson(a)stericsson.com> + * Author: Linus Walleij <linus.walleij(a)linaro.org> + * + * The DB3350 design and control registers are oriented around pads rather than + * pins, so we enumerate the pads we can mux rather than actual pins. The pads + * are connected to different pins in different packaging types, so it would + * be confusing. + */ +#include <linux/init.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/slab.h> +#include <linux/err.h> +#include <linux/pinctrl/pinctrl.h> +#include <linux/pinctrl/pinmux.h> + +/* + * Register definitions for the U300 Padmux control registers in the + * system controller + */ + +/* PAD MUX Control register 1 (LOW) 16bit (R/W) */ +#define U300_SYSCON_PMC1LR 0x007C +#define U300_SYSCON_PMC1LR_MASK 0xFFFF +#define U300_SYSCON_PMC1LR_CDI_MASK 0xC000 +#define U300_SYSCON_PMC1LR_CDI_CDI 0x0000 +#define U300_SYSCON_PMC1LR_CDI_EMIF 0x4000 +/* For BS335 */ +#define U300_SYSCON_PMC1LR_CDI_CDI2 0x8000 +#define U300_SYSCON_PMC1LR_CDI_WCDMA_APP_GPIO 0xC000 +/* For BS365 */ +#define U300_SYSCON_PMC1LR_CDI_GPIO 0x8000 +#define U300_SYSCON_PMC1LR_CDI_WCDMA 0xC000 +/* Common defs */ +#define U300_SYSCON_PMC1LR_PDI_MASK 0x3000 +#define U300_SYSCON_PMC1LR_PDI_PDI 0x0000 +#define U300_SYSCON_PMC1LR_PDI_EGG 0x1000 +#define U300_SYSCON_PMC1LR_PDI_WCDMA 0x3000 +#define U300_SYSCON_PMC1LR_MMCSD_MASK 0x0C00 +#define U300_SYSCON_PMC1LR_MMCSD_MMCSD 0x0000 +#define U300_SYSCON_PMC1LR_MMCSD_MSPRO 0x0400 +#define U300_SYSCON_PMC1LR_MMCSD_DSP 0x0800 +#define U300_SYSCON_PMC1LR_MMCSD_WCDMA 0x0C00 +#define U300_SYSCON_PMC1LR_ETM_MASK 0x0300 +#define U300_SYSCON_PMC1LR_ETM_ACC 0x0000 +#define U300_SYSCON_PMC1LR_ETM_APP 0x0100 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK 0x00C0 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_NFIF 0x0040 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM 0x0080 +#define U300_SYSCON_PMC1LR_EMIF_1_CS2_STATIC_2GB 0x00C0 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK 0x0030 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_NFIF 0x0010 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SDRAM 0x0020 +#define U300_SYSCON_PMC1LR_EMIF_1_CS1_SEMI 0x0030 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK 0x000C +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF 0x0004 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SDRAM 0x0008 +#define U300_SYSCON_PMC1LR_EMIF_1_CS0_SEMI 0x000C +#define U300_SYSCON_PMC1LR_EMIF_1_MASK 0x0003 +#define U300_SYSCON_PMC1LR_EMIF_1_STATIC 0x0000 +#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 0x0001 +#define U300_SYSCON_PMC1LR_EMIF_1_SDRAM1 0x0002 +#define U300_SYSCON_PMC1LR_EMIF_1 0x0003 +/* PAD MUX Control register 2 (HIGH) 16bit (R/W) */ +#define U300_SYSCON_PMC1HR 0x007E +#define U300_SYSCON_PMC1HR_MASK 0xFFFF +#define U300_SYSCON_PMC1HR_MISC_2_MASK 0xC000 +#define U300_SYSCON_PMC1HR_MISC_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_MISC_2_MSPRO 0x4000 +#define U300_SYSCON_PMC1HR_MISC_2_DSP 0x8000 +#define U300_SYSCON_PMC1HR_MISC_2_AAIF 0xC000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_MASK 0x3000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_NFIF 0x1000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_DSP 0x2000 +#define U300_SYSCON_PMC1HR_APP_GPIO_2_AAIF 0x3000 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_MASK 0x0C00 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_MMC 0x0400 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_DSP 0x0800 +#define U300_SYSCON_PMC1HR_APP_GPIO_1_AAIF 0x0C00 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK 0x0300 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI 0x0100 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_2_AAIF 0x0300 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK 0x00C0 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI 0x0040 +#define U300_SYSCON_PMC1HR_APP_SPI_CS_1_AAIF 0x00C0 +#define U300_SYSCON_PMC1HR_APP_SPI_2_MASK 0x0030 +#define U300_SYSCON_PMC1HR_APP_SPI_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_SPI_2_SPI 0x0010 +#define U300_SYSCON_PMC1HR_APP_SPI_2_DSP 0x0020 +#define U300_SYSCON_PMC1HR_APP_SPI_2_AAIF 0x0030 +#define U300_SYSCON_PMC1HR_APP_UART0_2_MASK 0x000C +#define U300_SYSCON_PMC1HR_APP_UART0_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_UART0_2_UART0 0x0004 +#define U300_SYSCON_PMC1HR_APP_UART0_2_NFIF_CS 0x0008 +#define U300_SYSCON_PMC1HR_APP_UART0_2_AAIF 0x000C +#define U300_SYSCON_PMC1HR_APP_UART0_1_MASK 0x0003 +#define U300_SYSCON_PMC1HR_APP_UART0_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC1HR_APP_UART0_1_UART0 0x0001 +#define U300_SYSCON_PMC1HR_APP_UART0_1_AAIF 0x0003 +/* Padmux 2 control */ +#define U300_SYSCON_PMC2R 0x100 +#define U300_SYSCON_PMC2R_APP_MISC_0_MASK 0x00C0 +#define U300_SYSCON_PMC2R_APP_MISC_0_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_0_EMIF_SDRAM 0x0040 +#define U300_SYSCON_PMC2R_APP_MISC_0_MMC 0x0080 +#define U300_SYSCON_PMC2R_APP_MISC_0_CDI2 0x00C0 +#define U300_SYSCON_PMC2R_APP_MISC_1_MASK 0x0300 +#define U300_SYSCON_PMC2R_APP_MISC_1_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_1_EMIF_SDRAM 0x0100 +#define U300_SYSCON_PMC2R_APP_MISC_1_MMC 0x0200 +#define U300_SYSCON_PMC2R_APP_MISC_1_CDI2 0x0300 +#define U300_SYSCON_PMC2R_APP_MISC_2_MASK 0x0C00 +#define U300_SYSCON_PMC2R_APP_MISC_2_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_2_EMIF_SDRAM 0x0400 +#define U300_SYSCON_PMC2R_APP_MISC_2_MMC 0x0800 +#define U300_SYSCON_PMC2R_APP_MISC_2_CDI2 0x0C00 +#define U300_SYSCON_PMC2R_APP_MISC_3_MASK 0x3000 +#define U300_SYSCON_PMC2R_APP_MISC_3_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_3_EMIF_SDRAM 0x1000 +#define U300_SYSCON_PMC2R_APP_MISC_3_MMC 0x2000 +#define U300_SYSCON_PMC2R_APP_MISC_3_CDI2 0x3000 +#define U300_SYSCON_PMC2R_APP_MISC_4_MASK 0xC000 +#define U300_SYSCON_PMC2R_APP_MISC_4_APP_GPIO 0x0000 +#define U300_SYSCON_PMC2R_APP_MISC_4_EMIF_SDRAM 0x4000 +#define U300_SYSCON_PMC2R_APP_MISC_4_MMC 0x8000 +#define U300_SYSCON_PMC2R_APP_MISC_4_ACC_GPIO 0xC000 +/* TODO: More SYSCON registers missing */ +#define U300_SYSCON_PMC3R 0x10C +#define U300_SYSCON_PMC3R_APP_MISC_11_MASK 0xC000 +#define U300_SYSCON_PMC3R_APP_MISC_11_SPI 0x4000 +#define U300_SYSCON_PMC3R_APP_MISC_10_MASK 0x3000 +#define U300_SYSCON_PMC3R_APP_MISC_10_SPI 0x1000 +/* TODO: Missing other configs */ +#define U300_SYSCON_PMC4R 0x168 +#define U300_SYSCON_PMC4R_APP_MISC_12_MASK 0x0003 +#define U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_13_MASK 0x000C +#define U300_SYSCON_PMC4R_APP_MISC_13_CDI 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA 0x0004 +#define U300_SYSCON_PMC4R_APP_MISC_13_SMIA2 0x0008 +#define U300_SYSCON_PMC4R_APP_MISC_13_APP_GPIO 0x000C +#define U300_SYSCON_PMC4R_APP_MISC_14_MASK 0x0030 +#define U300_SYSCON_PMC4R_APP_MISC_14_CDI 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_14_SMIA 0x0010 +#define U300_SYSCON_PMC4R_APP_MISC_14_CDI2 0x0020 +#define U300_SYSCON_PMC4R_APP_MISC_14_APP_GPIO 0x0030 +#define U300_SYSCON_PMC4R_APP_MISC_16_MASK 0x0300 +#define U300_SYSCON_PMC4R_APP_MISC_16_APP_GPIO_13 0x0000 +#define U300_SYSCON_PMC4R_APP_MISC_16_APP_UART1_CTS 0x0100 +#define U300_SYSCON_PMC4R_APP_MISC_16_EMIF_1_STATIC_CS5_N 0x0200 + +#define DRIVER_NAME "pinmux-u300" + +/* + * The DB3350 has 467 pads, I have enumerated the pads clockwise around the + * edges of the silicon, finger by finger. LTCORNER upper left is pad 0. + * Data taken from the PadRing chart, arranged like this: + * + * 0 ..... 104 + * 466 105 + * . . + * . . + * 358 224 + * 357 .... 225 + */ +#define U300_NUM_PADS 467 + +/* Pad names for the pinmux subsystem */ +static const struct pinctrl_pin_desc __refdata u300_pads[] = { + /* Pads along the top edge of the chip */ + PINCTRL_PIN(0, "P PAD VDD 28"), + PINCTRL_PIN(1, "P PAD GND 28"), + PINCTRL_PIN(2, "PO SIM RST N"), + PINCTRL_PIN(3, "VSSIO 25"), + PINCTRL_PIN(4, "VSSA ADDA ESDSUB"), + PINCTRL_PIN(5, "PWR VSSCOMMON"), + PINCTRL_PIN(6, "PI ADC I1 POS"), + PINCTRL_PIN(7, "PI ADC I1 NEG"), + PINCTRL_PIN(8, "PWR VSSAD0"), + PINCTRL_PIN(9, "PWR VCCAD0"), + PINCTRL_PIN(10, "PI ADC Q1 NEG"), + PINCTRL_PIN(11, "PI ADC Q1 POS"), + PINCTRL_PIN(12, "PWR VDDAD"), + PINCTRL_PIN(13, "PWR GNDAD"), + PINCTRL_PIN(14, "PI ADC I2 POS"), + PINCTRL_PIN(15, "PI ADC I2 NEG"), + PINCTRL_PIN(16, "PWR VSSAD1"), + PINCTRL_PIN(17, "PWR VCCAD1"), + PINCTRL_PIN(18, "PI ADC Q2 NEG"), + PINCTRL_PIN(19, "PI ADC Q2 POS"), + PINCTRL_PIN(20, "VSSA ADDA ESDSUB"), + PINCTRL_PIN(21, "PWR VCCGPAD"), + PINCTRL_PIN(22, "PI TX POW"), + PINCTRL_PIN(23, "PWR VSSGPAD"), + PINCTRL_PIN(24, "PO DAC I POS"), + PINCTRL_PIN(25, "PO DAC I NEG"), + PINCTRL_PIN(26, "PO DAC Q POS"), + PINCTRL_PIN(27, "PO DAC Q NEG"), + PINCTRL_PIN(28, "PWR VSSDA"), + PINCTRL_PIN(29, "PWR VCCDA"), + PINCTRL_PIN(30, "VSSA ADDA ESDSUB"), + PINCTRL_PIN(31, "P PAD VDDIO 11"), + PINCTRL_PIN(32, "PI PLL 26 FILTVDD"), + PINCTRL_PIN(33, "PI PLL 26 VCONT"), + PINCTRL_PIN(34, "PWR AGNDPLL2V5 32 13"), + PINCTRL_PIN(35, "PWR AVDDPLL2V5 32 13"), + PINCTRL_PIN(36, "VDDA PLL ESD"), + PINCTRL_PIN(37, "VSSA PLL ESD"), + PINCTRL_PIN(38, "VSS PLL"), + PINCTRL_PIN(39, "VDDC PLL"), + PINCTRL_PIN(40, "PWR AGNDPLL2V5 26 60"), + PINCTRL_PIN(41, "PWR AVDDPLL2V5 26 60"), + PINCTRL_PIN(42, "PWR AVDDPLL2V5 26 208"), + PINCTRL_PIN(43, "PWR AGNDPLL2V5 26 208"), + PINCTRL_PIN(44, "PWR AVDDPLL2V5 13 208"), + PINCTRL_PIN(45, "PWR AGNDPLL2V5 13 208"), + PINCTRL_PIN(46, "P PAD VSSIO 11"), + PINCTRL_PIN(47, "P PAD VSSIO 12"), + PINCTRL_PIN(48, "PI POW RST N"), + PINCTRL_PIN(49, "VDDC IO"), + PINCTRL_PIN(50, "P PAD VDDIO 16"), + PINCTRL_PIN(51, "PO RF WCDMA EN 4"), + PINCTRL_PIN(52, "PO RF WCDMA EN 3"), + PINCTRL_PIN(53, "PO RF WCDMA EN 2"), + PINCTRL_PIN(54, "PO RF WCDMA EN 1"), + PINCTRL_PIN(55, "PO RF WCDMA EN 0"), + PINCTRL_PIN(56, "PO GSM PA ENABLE"), + PINCTRL_PIN(57, "PO RF DATA STRB"), + PINCTRL_PIN(58, "PO RF DATA2"), + PINCTRL_PIN(59, "PIO RF DATA1"), + PINCTRL_PIN(60, "PIO RF DATA0"), + PINCTRL_PIN(61, "P PAD VDD 11"), + PINCTRL_PIN(62, "P PAD GND 11"), + PINCTRL_PIN(63, "P PAD VSSIO 16"), + PINCTRL_PIN(64, "P PAD VDDIO 18"), + PINCTRL_PIN(65, "PO RF CTRL STRB2"), + PINCTRL_PIN(66, "PO RF CTRL STRB1"), + PINCTRL_PIN(67, "PO RF CTRL STRB0"), + PINCTRL_PIN(68, "PIO RF CTRL DATA"), + PINCTRL_PIN(69, "PO RF CTRL CLK"), + PINCTRL_PIN(70, "PO TX ADC STRB"), + PINCTRL_PIN(71, "PO ANT SW 2"), + PINCTRL_PIN(72, "PO ANT SW 3"), + PINCTRL_PIN(73, "PO ANT SW 0"), + PINCTRL_PIN(74, "PO ANT SW 1"), + PINCTRL_PIN(75, "PO M CLKRQ"), + PINCTRL_PIN(76, "PI M CLK"), + PINCTRL_PIN(77, "PI RTC CLK"), + PINCTRL_PIN(78, "P PAD VDD 8"), + PINCTRL_PIN(79, "P PAD GND 8"), + PINCTRL_PIN(80, "P PAD VSSIO 13"), + PINCTRL_PIN(81, "P PAD VDDIO 13"), + PINCTRL_PIN(82, "PO SYS 1 CLK"), + PINCTRL_PIN(83, "PO SYS 2 CLK"), + PINCTRL_PIN(84, "PO SYS 0 CLK"), + PINCTRL_PIN(85, "PI SYS 0 CLKRQ"), + PINCTRL_PIN(86, "PO PWR MNGT CTRL 1"), + PINCTRL_PIN(87, "PO PWR MNGT CTRL 0"), + PINCTRL_PIN(88, "PO RESOUT2 RST N"), + PINCTRL_PIN(89, "PO RESOUT1 RST N"), + PINCTRL_PIN(90, "PO RESOUT0 RST N"), + PINCTRL_PIN(91, "PI SERVICE N"), + PINCTRL_PIN(92, "P PAD VDD 29"), + PINCTRL_PIN(93, "P PAD GND 29"), + PINCTRL_PIN(94, "P PAD VSSIO 8"), + PINCTRL_PIN(95, "P PAD VDDIO 8"), + PINCTRL_PIN(96, "PI EXT IRQ1 N"), + PINCTRL_PIN(97, "PI EXT IRQ0 N"), + PINCTRL_PIN(98, "PIO DC ON"), + PINCTRL_PIN(99, "PIO ACC APP I2C DATA"), + PINCTRL_PIN(100, "PIO ACC APP I2C CLK"), + PINCTRL_PIN(101, "P PAD VDD 12"), + PINCTRL_PIN(102, "P PAD GND 12"), + PINCTRL_PIN(103, "P PAD VSSIO 14"), + PINCTRL_PIN(104, "P PAD VDDIO 14"), + /* Pads along the right edge of the chip */ + PINCTRL_PIN(105, "PIO APP I2C1 DATA"), + PINCTRL_PIN(106, "PIO APP I2C1 CLK"), + PINCTRL_PIN(107, "PO KEY OUT0"), + PINCTRL_PIN(108, "PO KEY OUT1"), + PINCTRL_PIN(109, "PO KEY OUT2"), + PINCTRL_PIN(110, "PO KEY OUT3"), + PINCTRL_PIN(111, "PO KEY OUT4"), + PINCTRL_PIN(112, "PI KEY IN0"), + PINCTRL_PIN(113, "PI KEY IN1"), + PINCTRL_PIN(114, "PI KEY IN2"), + PINCTRL_PIN(115, "P PAD VDDIO 15"), + PINCTRL_PIN(116, "P PAD VSSIO 15"), + PINCTRL_PIN(117, "P PAD GND 13"), + PINCTRL_PIN(118, "P PAD VDD 13"), + PINCTRL_PIN(119, "PI KEY IN3"), + PINCTRL_PIN(120, "PI KEY IN4"), + PINCTRL_PIN(121, "PI KEY IN5"), + PINCTRL_PIN(122, "PIO APP PCM I2S1 DATA B"), + PINCTRL_PIN(123, "PIO APP PCM I2S1 DATA A"), + PINCTRL_PIN(124, "PIO APP PCM I2S1 WS"), + PINCTRL_PIN(125, "PIO APP PCM I2S1 CLK"), + PINCTRL_PIN(126, "PIO APP PCM I2S0 DATA B"), + PINCTRL_PIN(127, "PIO APP PCM I2S0 DATA A"), + PINCTRL_PIN(128, "PIO APP PCM I2S0 WS"), + PINCTRL_PIN(129, "PIO APP PCM I2S0 CLK"), + PINCTRL_PIN(130, "P PAD VDD 17"), + PINCTRL_PIN(131, "P PAD GND 17"), + PINCTRL_PIN(132, "P PAD VSSIO 19"), + PINCTRL_PIN(133, "P PAD VDDIO 19"), + PINCTRL_PIN(134, "UART0 RTS"), + PINCTRL_PIN(135, "UART0 CTS"), + PINCTRL_PIN(136, "UART0 TX"), + PINCTRL_PIN(137, "UART0 RX"), + PINCTRL_PIN(138, "PIO ACC SPI DO"), + PINCTRL_PIN(139, "PIO ACC SPI DI"), + PINCTRL_PIN(140, "PIO ACC SPI CS0 N"), + PINCTRL_PIN(141, "PIO ACC SPI CS1 N"), + PINCTRL_PIN(142, "PIO ACC SPI CS2 N"), + PINCTRL_PIN(143, "PIO ACC SPI CLK"), + PINCTRL_PIN(144, "PO PDI EXT RST N"), + PINCTRL_PIN(145, "P PAD VDDIO 22"), + PINCTRL_PIN(146, "P PAD VSSIO 22"), + PINCTRL_PIN(147, "P PAD GND 18"), + PINCTRL_PIN(148, "P PAD VDD 18"), + PINCTRL_PIN(149, "PIO PDI C0"), + PINCTRL_PIN(150, "PIO PDI C1"), + PINCTRL_PIN(151, "PIO PDI C2"), + PINCTRL_PIN(152, "PIO PDI C3"), + PINCTRL_PIN(153, "PIO PDI C4"), + PINCTRL_PIN(154, "PIO PDI C5"), + PINCTRL_PIN(155, "PIO PDI D0"), + PINCTRL_PIN(156, "PIO PDI D1"), + PINCTRL_PIN(157, "PIO PDI D2"), + PINCTRL_PIN(158, "PIO PDI D3"), + PINCTRL_PIN(159, "P PAD VDDIO 21"), + PINCTRL_PIN(160, "P PAD VSSIO 21"), + PINCTRL_PIN(161, "PIO PDI D4"), + PINCTRL_PIN(162, "PIO PDI D5"), + PINCTRL_PIN(163, "PIO PDI D6"), + PINCTRL_PIN(164, "PIO PDI D7"), + PINCTRL_PIN(165, "PIO MS INS"), + PINCTRL_PIN(166, "MMC DATA DIR LS"), + PINCTRL_PIN(167, "MMC DATA 3"), + PINCTRL_PIN(168, "MMC DATA 2"), + PINCTRL_PIN(169, "MMC DATA 1"), + PINCTRL_PIN(170, "MMC DATA 0"), + PINCTRL_PIN(171, "MMC CMD DIR LS"), + PINCTRL_PIN(172, "P PAD VDD 27"), + PINCTRL_PIN(173, "P PAD GND 27"), + PINCTRL_PIN(174, "P PAD VSSIO 20"), + PINCTRL_PIN(175, "P PAD VDDIO 20"), + PINCTRL_PIN(176, "MMC CMD"), + PINCTRL_PIN(177, "MMC CLK"), + PINCTRL_PIN(178, "PIO APP GPIO 14"), + PINCTRL_PIN(179, "PIO APP GPIO 13"), + PINCTRL_PIN(180, "PIO APP GPIO 11"), + PINCTRL_PIN(181, "PIO APP GPIO 25"), + PINCTRL_PIN(182, "PIO APP GPIO 24"), + PINCTRL_PIN(183, "PIO APP GPIO 23"), + PINCTRL_PIN(184, "PIO APP GPIO 22"), + PINCTRL_PIN(185, "PIO APP GPIO 21"), + PINCTRL_PIN(186, "PIO APP GPIO 20"), + PINCTRL_PIN(187, "P PAD VDD 19"), + PINCTRL_PIN(188, "P PAD GND 19"), + PINCTRL_PIN(189, "P PAD VSSIO 23"), + PINCTRL_PIN(190, "P PAD VDDIO 23"), + PINCTRL_PIN(191, "PIO APP GPIO 19"), + PINCTRL_PIN(192, "PIO APP GPIO 18"), + PINCTRL_PIN(193, "PIO APP GPIO 17"), + PINCTRL_PIN(194, "PIO APP GPIO 16"), + PINCTRL_PIN(195, "PI CI D1"), + PINCTRL_PIN(196, "PI CI D0"), + PINCTRL_PIN(197, "PI CI HSYNC"), + PINCTRL_PIN(198, "PI CI VSYNC"), + PINCTRL_PIN(199, "PI CI EXT CLK"), + PINCTRL_PIN(200, "PO CI EXT RST N"), + PINCTRL_PIN(201, "P PAD VSSIO 43"), + PINCTRL_PIN(202, "P PAD VDDIO 43"), + PINCTRL_PIN(203, "PI CI D6"), + PINCTRL_PIN(204, "PI CI D7"), + PINCTRL_PIN(205, "PI CI D2"), + PINCTRL_PIN(206, "PI CI D3"), + PINCTRL_PIN(207, "PI CI D4"), + PINCTRL_PIN(208, "PI CI D5"), + PINCTRL_PIN(209, "PI CI D8"), + PINCTRL_PIN(210, "PI CI D9"), + PINCTRL_PIN(211, "P PAD VDD 20"), + PINCTRL_PIN(212, "P PAD GND 20"), + PINCTRL_PIN(213, "P PAD VSSIO 24"), + PINCTRL_PIN(214, "P PAD VDDIO 24"), + PINCTRL_PIN(215, "P PAD VDDIO 26"), + PINCTRL_PIN(216, "PO EMIF 1 A26"), + PINCTRL_PIN(217, "PO EMIF 1 A25"), + PINCTRL_PIN(218, "P PAD VSSIO 26"), + PINCTRL_PIN(219, "PO EMIF 1 A24"), + PINCTRL_PIN(220, "PO EMIF 1 A23"), + /* Pads along the bottom edge of the chip */ + PINCTRL_PIN(221, "PO EMIF 1 A22"), + PINCTRL_PIN(222, "PO EMIF 1 A21"), + PINCTRL_PIN(223, "P PAD VDD 21"), + PINCTRL_PIN(224, "P PAD GND 21"), + PINCTRL_PIN(225, "P PAD VSSIO 27"), + PINCTRL_PIN(226, "P PAD VDDIO 27"), + PINCTRL_PIN(227, "PO EMIF 1 A20"), + PINCTRL_PIN(228, "PO EMIF 1 A19"), + PINCTRL_PIN(229, "PO EMIF 1 A18"), + PINCTRL_PIN(230, "PO EMIF 1 A17"), + PINCTRL_PIN(231, "P PAD VDDIO 28"), + PINCTRL_PIN(232, "P PAD VSSIO 28"), + PINCTRL_PIN(233, "PO EMIF 1 A16"), + PINCTRL_PIN(234, "PIO EMIF 1 D15"), + PINCTRL_PIN(235, "PO EMIF 1 A15"), + PINCTRL_PIN(236, "PIO EMIF 1 D14"), + PINCTRL_PIN(237, "P PAD VDD 22"), + PINCTRL_PIN(238, "P PAD GND 22"), + PINCTRL_PIN(239, "P PAD VSSIO 29"), + PINCTRL_PIN(240, "P PAD VDDIO 29"), + PINCTRL_PIN(241, "PO EMIF 1 A14"), + PINCTRL_PIN(242, "PIO EMIF 1 D13"), + PINCTRL_PIN(243, "PO EMIF 1 A13"), + PINCTRL_PIN(244, "PIO EMIF 1 D12"), + PINCTRL_PIN(245, "P PAD VSSIO 30"), + PINCTRL_PIN(246, "P PAD VDDIO 30"), + PINCTRL_PIN(247, "PO EMIF 1 A12"), + PINCTRL_PIN(248, "PIO EMIF 1 D11"), + PINCTRL_PIN(249, "PO EMIF 1 A11"), + PINCTRL_PIN(250, "PIO EMIF 1 D10"), + PINCTRL_PIN(251, "P PAD VSSIO 31"), + PINCTRL_PIN(252, "P PAD VDDIO 31"), + PINCTRL_PIN(253, "PO EMIF 1 A10"), + PINCTRL_PIN(254, "PIO EMIF 1 D09"), + PINCTRL_PIN(255, "PO EMIF 1 A09"), + PINCTRL_PIN(256, "P PAD VDDIO 32"), + PINCTRL_PIN(257, "P PAD VSSIO 32"), + PINCTRL_PIN(258, "P PAD GND 24"), + PINCTRL_PIN(259, "P PAD VDD 24"), + PINCTRL_PIN(260, "PIO EMIF 1 D08"), + PINCTRL_PIN(261, "PO EMIF 1 A08"), + PINCTRL_PIN(262, "PIO EMIF 1 D07"), + PINCTRL_PIN(263, "PO EMIF 1 A07"), + PINCTRL_PIN(264, "P PAD VDDIO 33"), + PINCTRL_PIN(265, "P PAD VSSIO 33"), + PINCTRL_PIN(266, "PIO EMIF 1 D06"), + PINCTRL_PIN(267, "PO EMIF 1 A06"), + PINCTRL_PIN(268, "PIO EMIF 1 D05"), + PINCTRL_PIN(269, "PO EMIF 1 A05"), + PINCTRL_PIN(270, "P PAD VDDIO 34"), + PINCTRL_PIN(271, "P PAD VSSIO 34"), + PINCTRL_PIN(272, "PIO EMIF 1 D04"), + PINCTRL_PIN(273, "PO EMIF 1 A04"), + PINCTRL_PIN(274, "PIO EMIF 1 D03"), + PINCTRL_PIN(275, "PO EMIF 1 A03"), + PINCTRL_PIN(276, "P PAD VDDIO 35"), + PINCTRL_PIN(277, "P PAD VSSIO 35"), + PINCTRL_PIN(278, "P PAD GND 23"), + PINCTRL_PIN(279, "P PAD VDD 23"), + PINCTRL_PIN(280, "PIO EMIF 1 D02"), + PINCTRL_PIN(281, "PO EMIF 1 A02"), + PINCTRL_PIN(282, "PIO EMIF 1 D01"), + PINCTRL_PIN(283, "PO EMIF 1 A01"), + PINCTRL_PIN(284, "P PAD VDDIO 36"), + PINCTRL_PIN(285, "P PAD VSSIO 36"), + PINCTRL_PIN(286, "PIO EMIF 1 D00"), + PINCTRL_PIN(287, "PO EMIF 1 BE1 N"), + PINCTRL_PIN(288, "PO EMIF 1 BE0 N"), + PINCTRL_PIN(289, "PO EMIF 1 ADV N"), + PINCTRL_PIN(290, "P PAD VDDIO 37"), + PINCTRL_PIN(291, "P PAD VSSIO 37"), + PINCTRL_PIN(292, "PO EMIF 1 SD CKE0"), + PINCTRL_PIN(293, "PO EMIF 1 OE N"), + PINCTRL_PIN(294, "PO EMIF 1 WE N"), + PINCTRL_PIN(295, "P PAD VDDIO 38"), + PINCTRL_PIN(296, "P PAD VSSIO 38"), + PINCTRL_PIN(297, "PO EMIF 1 CLK"), + PINCTRL_PIN(298, "PIO EMIF 1 SD CLK"), + PINCTRL_PIN(299, "P PAD VSSIO 45 (not bonded)"), + PINCTRL_PIN(300, "P PAD VDDIO 42"), + PINCTRL_PIN(301, "P PAD VSSIO 42"), + PINCTRL_PIN(302, "P PAD GND 31"), + PINCTRL_PIN(303, "P PAD VDD 31"), + PINCTRL_PIN(304, "PI EMIF 1 RET CLK"), + PINCTRL_PIN(305, "PI EMIF 1 WAIT N"), + PINCTRL_PIN(306, "PI EMIF 1 NFIF READY"), + PINCTRL_PIN(307, "PO EMIF 1 SD CKE1"), + PINCTRL_PIN(308, "PO EMIF 1 CS3 N"), + PINCTRL_PIN(309, "P PAD VDD 25"), + PINCTRL_PIN(310, "P PAD GND 25"), + PINCTRL_PIN(311, "P PAD VSSIO 39"), + PINCTRL_PIN(312, "P PAD VDDIO 39"), + PINCTRL_PIN(313, "PO EMIF 1 CS2 N"), + PINCTRL_PIN(314, "PO EMIF 1 CS1 N"), + PINCTRL_PIN(315, "PO EMIF 1 CS0 N"), + PINCTRL_PIN(316, "PO ETM TRACE PKT0"), + PINCTRL_PIN(317, "PO ETM TRACE PKT1"), + PINCTRL_PIN(318, "PO ETM TRACE PKT2"), + PINCTRL_PIN(319, "P PAD VDD 30"), + PINCTRL_PIN(320, "P PAD GND 30"), + PINCTRL_PIN(321, "P PAD VSSIO 44"), + PINCTRL_PIN(322, "P PAD VDDIO 44"), + PINCTRL_PIN(323, "PO ETM TRACE PKT3"), + PINCTRL_PIN(324, "PO ETM TRACE PKT4"), + PINCTRL_PIN(325, "PO ETM TRACE PKT5"), + PINCTRL_PIN(326, "PO ETM TRACE PKT6"), + PINCTRL_PIN(327, "PO ETM TRACE PKT7"), + PINCTRL_PIN(328, "PO ETM PIPE STAT0"), + PINCTRL_PIN(329, "P PAD VDD 26"), + PINCTRL_PIN(330, "P PAD GND 26"), + PINCTRL_PIN(331, "P PAD VSSIO 40"), + PINCTRL_PIN(332, "P PAD VDDIO 40"), + PINCTRL_PIN(333, "PO ETM PIPE STAT1"), + PINCTRL_PIN(334, "PO ETM PIPE STAT2"), + PINCTRL_PIN(335, "PO ETM TRACE CLK"), + PINCTRL_PIN(336, "PO ETM TRACE SYNC"), + PINCTRL_PIN(337, "PIO ACC GPIO 33"), + PINCTRL_PIN(338, "PIO ACC GPIO 32"), + PINCTRL_PIN(339, "PIO ACC GPIO 30"), + PINCTRL_PIN(340, "PIO ACC GPIO 29"), + PINCTRL_PIN(341, "P PAD VDDIO 17"), + PINCTRL_PIN(342, "P PAD VSSIO 17"), + PINCTRL_PIN(343, "P PAD GND 15"), + PINCTRL_PIN(344, "P PAD VDD 15"), + PINCTRL_PIN(345, "PIO ACC GPIO 28"), + PINCTRL_PIN(346, "PIO ACC GPIO 27"), + PINCTRL_PIN(347, "PIO ACC GPIO 16"), + PINCTRL_PIN(348, "PI TAP TMS"), + PINCTRL_PIN(349, "PI TAP TDI"), + PINCTRL_PIN(350, "PO TAP TDO"), + PINCTRL_PIN(351, "PI TAP RST N"), + /* Pads along the left edge of the chip */ + PINCTRL_PIN(352, "PI EMU MODE 0"), + PINCTRL_PIN(353, "PO TAP RET CLK"), + PINCTRL_PIN(354, "PI TAP CLK"), + PINCTRL_PIN(355, "PO EMIF 0 SD CS N"), + PINCTRL_PIN(356, "PO EMIF 0 SD CAS N"), + PINCTRL_PIN(357, "PO EMIF 0 SD WE N"), + PINCTRL_PIN(358, "P PAD VDDIO 1"), + PINCTRL_PIN(359, "P PAD VSSIO 1"), + PINCTRL_PIN(360, "P PAD GND 1"), + PINCTRL_PIN(361, "P PAD VDD 1"), + PINCTRL_PIN(362, "PO EMIF 0 SD CKE"), + PINCTRL_PIN(363, "PO EMIF 0 SD DQML"), + PINCTRL_PIN(364, "PO EMIF 0 SD DQMU"), + PINCTRL_PIN(365, "PO EMIF 0 SD RAS N"), + PINCTRL_PIN(366, "PIO EMIF 0 D15"), + PINCTRL_PIN(367, "PO EMIF 0 A15"), + PINCTRL_PIN(368, "PIO EMIF 0 D14"), + PINCTRL_PIN(369, "PO EMIF 0 A14"), + PINCTRL_PIN(370, "PIO EMIF 0 D13"), + PINCTRL_PIN(371, "PO EMIF 0 A13"), + PINCTRL_PIN(372, "P PAD VDDIO 2"), + PINCTRL_PIN(373, "P PAD VSSIO 2"), + PINCTRL_PIN(374, "P PAD GND 2"), + PINCTRL_PIN(375, "P PAD VDD 2"), + PINCTRL_PIN(376, "PIO EMIF 0 D12"), + PINCTRL_PIN(377, "PO EMIF 0 A12"), + PINCTRL_PIN(378, "PIO EMIF 0 D11"), + PINCTRL_PIN(379, "PO EMIF 0 A11"), + PINCTRL_PIN(380, "PIO EMIF 0 D10"), + PINCTRL_PIN(381, "PO EMIF 0 A10"), + PINCTRL_PIN(382, "PIO EMIF 0 D09"), + PINCTRL_PIN(383, "PO EMIF 0 A09"), + PINCTRL_PIN(384, "PIO EMIF 0 D08"), + PINCTRL_PIN(385, "PO EMIF 0 A08"), + PINCTRL_PIN(386, "PIO EMIF 0 D07"), + PINCTRL_PIN(387, "PO EMIF 0 A07"), + PINCTRL_PIN(388, "P PAD VDDIO 3"), + PINCTRL_PIN(389, "P PAD VSSIO 3"), + PINCTRL_PIN(390, "P PAD GND 3"), + PINCTRL_PIN(391, "P PAD VDD 3"), + PINCTRL_PIN(392, "PO EFUSE RDOUT1"), + PINCTRL_PIN(393, "PIO EMIF 0 D06"), + PINCTRL_PIN(394, "PO EMIF 0 A06"), + PINCTRL_PIN(395, "PIO EMIF 0 D05"), + PINCTRL_PIN(396, "PO EMIF 0 A05"), + PINCTRL_PIN(397, "PIO EMIF 0 D04"), + PINCTRL_PIN(398, "PO EMIF 0 A04"), + PINCTRL_PIN(399, "A PADS/A VDDCO1v82v5 GND 80U SF LIN VDDCO AF"), + PINCTRL_PIN(400, "PWR VDDCO AF"), + PINCTRL_PIN(401, "PWR EFUSE HV1"), + PINCTRL_PIN(402, "P PAD VSSIO 4"), + PINCTRL_PIN(403, "P PAD VDDIO 4"), + PINCTRL_PIN(404, "P PAD GND 4"), + PINCTRL_PIN(405, "P PAD VDD 4"), + PINCTRL_PIN(406, "PIO EMIF 0 D03"), + PINCTRL_PIN(407, "PO EMIF 0 A03"), + PINCTRL_PIN(408, "PWR EFUSE HV2"), + PINCTRL_PIN(409, "PWR EFUSE HV3"), + PINCTRL_PIN(410, "PIO EMIF 0 D02"), + PINCTRL_PIN(411, "PO EMIF 0 A02"), + PINCTRL_PIN(412, "PIO EMIF 0 D01"), + PINCTRL_PIN(413, "P PAD VDDIO 5"), + PINCTRL_PIN(414, "P PAD VSSIO 5"), + PINCTRL_PIN(415, "P PAD GND 5"), + PINCTRL_PIN(416, "P PAD VDD 5"), + PINCTRL_PIN(417, "PO EMIF 0 A01"), + PINCTRL_PIN(418, "PIO EMIF 0 D00"), + PINCTRL_PIN(419, "IF 0 SD CLK"), + PINCTRL_PIN(420, "APP SPI CLK"), + PINCTRL_PIN(421, "APP SPI DO"), + PINCTRL_PIN(422, "APP SPI DI"), + PINCTRL_PIN(423, "APP SPI CS0"), + PINCTRL_PIN(424, "APP SPI CS1"), + PINCTRL_PIN(425, "APP SPI CS2"), + PINCTRL_PIN(426, "PIO APP GPIO 10"), + PINCTRL_PIN(427, "P PAD VDDIO 41"), + PINCTRL_PIN(428, "P PAD VSSIO 41"), + PINCTRL_PIN(429, "P PAD GND 6"), + PINCTRL_PIN(430, "P PAD VDD 6"), + PINCTRL_PIN(431, "PIO ACC SDIO0 CMD"), + PINCTRL_PIN(432, "PIO ACC SDIO0 CK"), + PINCTRL_PIN(433, "PIO ACC SDIO0 D3"), + PINCTRL_PIN(434, "PIO ACC SDIO0 D2"), + PINCTRL_PIN(435, "PIO ACC SDIO0 D1"), + PINCTRL_PIN(436, "PIO ACC SDIO0 D0"), + PINCTRL_PIN(437, "PIO USB PU"), + PINCTRL_PIN(438, "PIO USB SP"), + PINCTRL_PIN(439, "PIO USB DAT VP"), + PINCTRL_PIN(440, "PIO USB SE0 VM"), + PINCTRL_PIN(441, "PIO USB OE"), + PINCTRL_PIN(442, "PIO USB SUSP"), + PINCTRL_PIN(443, "P PAD VSSIO 6"), + PINCTRL_PIN(444, "P PAD VDDIO 6"), + PINCTRL_PIN(445, "PIO USB PUEN"), + PINCTRL_PIN(446, "PIO ACC UART0 RX"), + PINCTRL_PIN(447, "PIO ACC UART0 TX"), + PINCTRL_PIN(448, "PIO ACC UART0 CTS"), + PINCTRL_PIN(449, "PIO ACC UART0 RTS"), + PINCTRL_PIN(450, "PIO ACC UART3 RX"), + PINCTRL_PIN(451, "PIO ACC UART3 TX"), + PINCTRL_PIN(452, "PIO ACC UART3 CTS"), + PINCTRL_PIN(453, "PIO ACC UART3 RTS"), + PINCTRL_PIN(454, "PIO ACC IRDA TX"), + PINCTRL_PIN(455, "P PAD VDDIO 7"), + PINCTRL_PIN(456, "P PAD VSSIO 7"), + PINCTRL_PIN(457, "P PAD GND 7"), + PINCTRL_PIN(458, "P PAD VDD 7"), + PINCTRL_PIN(459, "PIO ACC IRDA RX"), + PINCTRL_PIN(460, "PIO ACC PCM I2S CLK"), + PINCTRL_PIN(461, "PIO ACC PCM I2S WS"), + PINCTRL_PIN(462, "PIO ACC PCM I2S DATA A"), + PINCTRL_PIN(463, "PIO ACC PCM I2S DATA B"), + PINCTRL_PIN(464, "PO SIM CLK"), + PINCTRL_PIN(465, "PIO ACC IRDA SD"), + PINCTRL_PIN(466, "PIO SIM DATA"), +}; + +/** + * @dev: a pointer back to containing device + * @virtbase: the offset to the controller in virtual memory + */ +struct u300_pmx { + struct device *dev; + struct pinctrl_dev *pctl; + u32 phybase; + u32 physize; + void __iomem *virtbase; +}; + +/** + * u300_pmx_registers - the array of registers read/written for each pinmux + * shunt setting + */ +const u32 u300_pmx_registers[] = { + U300_SYSCON_PMC1LR, + U300_SYSCON_PMC1HR, + U300_SYSCON_PMC2R, + U300_SYSCON_PMC3R, + U300_SYSCON_PMC4R, +}; + +/** + * struct u300_pin_group - describes a U300 pin group + * @name: the name of this specific pin group + * @pins: an array of discrete physical pins used in this group, taken + * from the driver-local pin enumeration space + * @num_pins: the number of pins in this group array, i.e. the number of + * elements in .pins so we can iterate over that array + */ +struct u300_pin_group { + const char *name; + const unsigned int *pins; + const unsigned num_pins; +}; + +/** + * struct pmx_onmask - mask bits to enable/disable padmux + * @mask: mask bits to disable + * @val: mask bits to enable + * + * onmask lazy dog: + * onmask = { + * {"PMC1LR" mask, "PMC1LR" value}, + * {"PMC1HR" mask, "PMC1HR" value}, + * {"PMC2R" mask, "PMC2R" value}, + * {"PMC3R" mask, "PMC3R" value}, + * {"PMC4R" mask, "PMC4R" value} + * } + */ +struct u300_pmx_mask { + u16 mask; + u16 bits; +}; + +/* The chip power pins are VDD, GND, VDDIO and VSSIO */ +static const unsigned power_pins[] = { 0, 1, 3, 31, 46, 47, 49, 50, 61, 62, 63, + 64, 78, 79, 80, 81, 92, 93, 94, 95, 101, 102, 103, 104, 115, 116, 117, + 118, 130, 131, 132, 133, 145, 146, 147, 148, 159, 160, 172, 173, 174, + 175, 187, 188, 189, 190, 201, 202, 211, 212, 213, 214, 215, 218, 223, + 224, 225, 226, 231, 232, 237, 238, 239, 240, 245, 246, 251, 252, 256, + 257, 258, 259, 264, 265, 270, 271, 276, 277, 278, 279, 284, 285, 290, + 291, 295, 296, 299, 300, 301, 302, 303, 309, 310, 311, 312, 319, 320, + 321, 322, 329, 330, 331, 332, 341, 342, 343, 344, 358, 359, 360, 361, + 372, 373, 374, 375, 388, 389, 390, 391, 402, 403, 404, 405, 413, 414, + 415, 416, 427, 428, 429, 430, 443, 444, 455, 456, 457, 458 }; +static const unsigned emif0_pins[] = { 355, 356, 357, 362, 363, 364, 365, 366, + 367, 368, 369, 370, 371, 376, 377, 378, 379, 380, 381, 382, 383, 384, + 385, 386, 387, 393, 394, 395, 396, 397, 398, 406, 407, 410, 411, 412, + 417, 418 }; +static const unsigned emif1_pins[] = { 216, 217, 219, 220, 221, 222, 227, 228, + 229, 230, 233, 234, 235, 236, 241, 242, 243, 244, 247, 248, 249, 250, + 253, 254, 255, 260, 261, 262, 263, 266, 267, 268, 269, 272, 273, 274, + 275, 280, 281, 282, 283, 286, 287, 288, 289, 292, 293, 294, 297, 298, + 304, 305, 306, 307, 308, 313, 314, 315 }; +static const unsigned uart0_pins[] = { 134, 135, 136, 137 }; +static const unsigned mmc0_pins[] = { 166, 167, 168, 169, 170, 171, 176, 177 }; +static const unsigned spi0_pins[] = { 420, 421, 422, 423, 424, 425 }; + +static const struct u300_pmx_mask emif0_mask[] = { + {0, 0}, + {0, 0}, + {0, 0}, + {0, 0}, + {0, 0}, +}; + +static const struct u300_pmx_mask emif1_mask[] = { + /* + * This connects the SDRAM to CS2 and a NAND flash to + * CS0 on the EMIF. + */ + { + U300_SYSCON_PMC1LR_EMIF_1_CS2_MASK | + U300_SYSCON_PMC1LR_EMIF_1_CS1_MASK | + U300_SYSCON_PMC1LR_EMIF_1_CS0_MASK | + U300_SYSCON_PMC1LR_EMIF_1_MASK, + U300_SYSCON_PMC1LR_EMIF_1_CS2_SDRAM | + U300_SYSCON_PMC1LR_EMIF_1_CS1_STATIC | + U300_SYSCON_PMC1LR_EMIF_1_CS0_NFIF | + U300_SYSCON_PMC1LR_EMIF_1_SDRAM0 + }, + {0, 0}, + {0, 0}, + {0, 0}, + {0, 0}, +}; + +static const struct u300_pmx_mask uart0_mask[] = { + {0, 0}, + { + U300_SYSCON_PMC1HR_APP_UART0_1_MASK | + U300_SYSCON_PMC1HR_APP_UART0_2_MASK, + U300_SYSCON_PMC1HR_APP_UART0_1_UART0 | + U300_SYSCON_PMC1HR_APP_UART0_2_UART0 + }, + {0, 0}, + {0, 0}, + {0, 0}, +}; + +static const struct u300_pmx_mask mmc0_mask[] = { + { U300_SYSCON_PMC1LR_MMCSD_MASK, U300_SYSCON_PMC1LR_MMCSD_MMCSD}, + {0, 0}, + {0, 0}, + {0, 0}, + { U300_SYSCON_PMC4R_APP_MISC_12_MASK, + U300_SYSCON_PMC4R_APP_MISC_12_APP_GPIO } +}; + +static const struct u300_pmx_mask spi0_mask[] = { + {0, 0}, + { + U300_SYSCON_PMC1HR_APP_SPI_2_MASK | + U300_SYSCON_PMC1HR_APP_SPI_CS_1_MASK | + U300_SYSCON_PMC1HR_APP_SPI_CS_2_MASK, + U300_SYSCON_PMC1HR_APP_SPI_2_SPI | + U300_SYSCON_PMC1HR_APP_SPI_CS_1_SPI | + U300_SYSCON_PMC1HR_APP_SPI_CS_2_SPI + }, + {0, 0}, + {0, 0}, + {0, 0} +}; + +static const struct u300_pin_group u300_pin_groups[] = { + { + .name = "powergrp", + .pins = power_pins, + .num_pins = ARRAY_SIZE(power_pins), + }, + { + .name = "emif0grp", + .pins = emif0_pins, + .num_pins = ARRAY_SIZE(emif0_pins), + }, + { + .name = "emif1grp", + .pins = emif1_pins, + .num_pins = ARRAY_SIZE(emif1_pins), + }, + { + .name = "uart0grp", + .pins = uart0_pins, + .num_pins = ARRAY_SIZE(uart0_pins), + }, + { + .name = "mmc0grp", + .pins = mmc0_pins, + .num_pins = ARRAY_SIZE(mmc0_pins), + }, + { + .name = "spi0grp", + .pins = spi0_pins, + .num_pins = ARRAY_SIZE(spi0_pins), + }, +}; + +static int u300_list_groups(struct pinctrl_dev *pctldev, unsigned selector) +{ + if (selector >= ARRAY_SIZE(u300_pin_groups)) + return -EINVAL; + return 0; +} + +static const char *u300_get_group_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + if (selector >= ARRAY_SIZE(u300_pin_groups)) + return NULL; + return u300_pin_groups[selector].name; +} + +static int u300_get_group_pins(struct pinctrl_dev *pctldev, unsigned selector, + unsigned ** const pins, + unsigned * const num_pins) +{ + if (selector >= ARRAY_SIZE(u300_pin_groups)) + return -EINVAL; + *pins = (unsigned *) u300_pin_groups[selector].pins; + *num_pins = u300_pin_groups[selector].num_pins; + return 0; +} + +static void u300_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s, + unsigned offset) +{ + seq_printf(s, " " DRIVER_NAME); +} + +static struct pinctrl_ops u300_pctrl_ops = { + .list_groups = u300_list_groups, + .get_group_name = u300_get_group_name, + .get_group_pins = u300_get_group_pins, + .pin_dbg_show = u300_pin_dbg_show, +}; + +/* + * Here we define the available functions and their corresponding pin groups + */ + +/** + * struct u300_pmx_func - describes U300 pinmux functions + * @name: the name of this specific function + * @groups: corresponding pin groups + * @onmask: bits to set to enable this when doing pin muxing + */ +struct u300_pmx_func { + const char *name; + const char * const *groups; + const unsigned num_groups; + const struct u300_pmx_mask *mask; +}; + +static const char * const powergrps[] = { "powergrp" }; +static const char * const emif0grps[] = { "emif0grp" }; +static const char * const emif1grps[] = { "emif1grp" }; +static const char * const uart0grps[] = { "uart0grp" }; +static const char * const mmc0grps[] = { "mmc0grp" }; +static const char * const spi0grps[] = { "spi0grp" }; + +static const struct u300_pmx_func u300_pmx_functions[] = { + { + .name = "power", + .groups = powergrps, + .num_groups = ARRAY_SIZE(powergrps), + /* Mask is N/A */ + }, + { + .name = "emif0", + .groups = emif0grps, + .num_groups = ARRAY_SIZE(emif0grps), + .mask = emif0_mask, + }, + { + .name = "emif1", + .groups = emif1grps, + .num_groups = ARRAY_SIZE(emif1grps), + .mask = emif1_mask, + }, + { + .name = "uart0", + .groups = uart0grps, + .num_groups = ARRAY_SIZE(uart0grps), + .mask = uart0_mask, + }, + { + .name = "mmc0", + .groups = mmc0grps, + .num_groups = ARRAY_SIZE(mmc0grps), + .mask = mmc0_mask, + }, + { + .name = "spi0", + .groups = spi0grps, + .num_groups = ARRAY_SIZE(spi0grps), + .mask = spi0_mask, + }, +}; + +static void u300_pmx_endisable(struct u300_pmx *upmx, unsigned selector, + bool enable) +{ + u16 regval, val, mask; + int i; + + for (i = 0; i < ARRAY_SIZE(u300_pmx_registers); i++) { + if (enable) + val = u300_pmx_functions[selector].mask->bits; + else + val = 0; + + mask = u300_pmx_functions[selector].mask->mask; + if (mask != 0) { + regval = readw(upmx->virtbase + u300_pmx_registers[i]); + regval &= ~mask; + regval |= val; + writew(regval, upmx->virtbase + u300_pmx_registers[i]); + } + } +} + +static int u300_pmx_enable(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group) +{ + struct u300_pmx *upmx; + + /* There is nothing to do with the power pins */ + if (selector == 0) + return 0; + + upmx = pctldev_get_drvdata(pctldev); + u300_pmx_endisable(upmx, selector, true); + + return 0; +} + +static void u300_pmx_disable(struct pinctrl_dev *pctldev, unsigned selector, + unsigned group) +{ + struct u300_pmx *upmx; + + /* There is nothing to do with the power pins */ + if (selector == 0) + return; + + upmx = pctldev_get_drvdata(pctldev); + u300_pmx_endisable(upmx, selector, false); +} + +static int u300_pmx_list_funcs(struct pinctrl_dev *pctldev, unsigned selector) +{ + if (selector >= ARRAY_SIZE(u300_pmx_functions)) + return -EINVAL; + return 0; +} + +static const char *u300_pmx_get_func_name(struct pinctrl_dev *pctldev, + unsigned selector) +{ + return u300_pmx_functions[selector].name; +} + +static int u300_pmx_get_groups(struct pinctrl_dev *pctldev, unsigned selector, + const char * const **groups, + unsigned * const num_groups) +{ + *groups = u300_pmx_functions[selector].groups; + *num_groups = u300_pmx_functions[selector].num_groups; + return 0; +} + +static struct pinmux_ops u300_pmx_ops = { + .list_functions = u300_pmx_list_funcs, + .get_function_name = u300_pmx_get_func_name, + .get_function_groups = u300_pmx_get_groups, + .enable = u300_pmx_enable, + .disable = u300_pmx_disable, +}; + +/* + * FIXME: this will be set to sane values as this driver engulfs + * drivers/gpio/gpio-u300.c and we really know this stuff. + */ +static struct pinctrl_gpio_range u300_gpio_range = { + .name = "COH901*", + .id = 0, + .base = 0, + .npins = 64, +}; + +static struct pinctrl_desc u300_pmx_desc = { + .name = DRIVER_NAME, + .pins = u300_pads, + .npins = ARRAY_SIZE(u300_pads), + .maxpin = U300_NUM_PADS-1, + .pctlops = &u300_pctrl_ops, + .pmxops = &u300_pmx_ops, + .owner = THIS_MODULE, +}; + +static void __init u300_pmx_dumpregs(struct u300_pmx *upmx) +{ + u16 regval; + int i; + + for (i = 0; i < ARRAY_SIZE(u300_pmx_registers); i++) { + regval = readw(upmx->virtbase + u300_pmx_registers[i]); + dev_info(upmx->dev, "PMX%u: 0x%04x\n", i, regval); + } +} + +static int __init u300_pmx_probe(struct platform_device *pdev) +{ + int ret; + struct u300_pmx *upmx; + struct resource *res; + + /* Create state holders etc for this driver */ + upmx = devm_kzalloc(&pdev->dev, sizeof(struct u300_pmx), GFP_KERNEL); + if (!upmx) + return -ENOMEM; + + upmx->dev = &pdev->dev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + ret = -ENOENT; + goto out_no_resource; + } + upmx->phybase = res->start; + upmx->physize = resource_size(res); + + if (request_mem_region(upmx->phybase, upmx->physize, + DRIVER_NAME) == NULL) { + ret = -EBUSY; + goto out_no_memregion; + } + + upmx->virtbase = ioremap(upmx->phybase, upmx->physize); + if (!upmx->virtbase) { + ret = -ENOMEM; + goto out_no_remap; + } + + upmx->pctl = pinctrl_register(&u300_pmx_desc, &pdev->dev, upmx); + if (IS_ERR(upmx->pctl)) { + dev_err(&pdev->dev, "could not register U300 pinmux driver\n"); + ret = PTR_ERR(upmx->pctl); + goto out_no_pmx; + } + + /* We will handle a range of GPIO pins */ + pinctrl_add_gpio_range(upmx->pctl, &u300_gpio_range); + + platform_set_drvdata(pdev, upmx); + + u300_pmx_dumpregs(upmx); + + dev_info(&pdev->dev, "initialized U300 pinmux driver\n"); + + return 0; + +out_no_pmx: + iounmap(upmx->virtbase); +out_no_remap: + platform_set_drvdata(pdev, NULL); +out_no_memregion: + release_mem_region(upmx->phybase, upmx->physize); +out_no_resource: + devm_kfree(&pdev->dev, upmx); + return ret; +} + +static int __exit u300_pmx_remove(struct platform_device *pdev) +{ + struct u300_pmx *upmx = platform_get_drvdata(pdev); + + pinctrl_remove_gpio_range(upmx->pctl, &u300_gpio_range); + pinctrl_unregister(upmx->pctl); + iounmap(upmx->virtbase); + release_mem_region(upmx->phybase, upmx->physize); + platform_set_drvdata(pdev, NULL); + devm_kfree(&pdev->dev, upmx); + + return 0; +} + +static struct platform_driver u300_pmx_driver = { + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + }, + .remove = __exit_p(u300_pmx_remove), +}; + +static int __init u300_pmx_init(void) +{ + return platform_driver_probe(&u300_pmx_driver, u300_pmx_probe); +} +arch_initcall(u300_pmx_init); + +static void __exit u300_pmx_exit(void) +{ + platform_driver_unregister(&u300_pmx_driver); +} +module_exit(u300_pmx_exit); + +MODULE_AUTHOR("Linus Walleij <linus.walleij(a)linaro.org>"); +MODULE_DESCRIPTION("U300 pin control driver"); +MODULE_LICENSE("GPL v2"); -- 1.7.3.2

13 years, 10 months

Announce: TILT tracking Androidization trees

by Andy Green

Hi - TI Landing Team has added a couple of new trees to our git repo over the weekend http://git.linaro.org/gitweb?p=people/andygreen/kernel-tilt.git;a=summary Both of them track Linus HEAD, currently at 3.1-rc8. First is "linaro-androidization-tracking", this is Linus HEAD plus a set of Androidization patches formed from common-3.0 and common-3.1. "common-3.1 you say?", yes, TI needed a tracking Androidization tree and have made their own public one using pieces from common-3.1. You can find TI's tree that was an ingredient in this here if you're interested, it's public http://git.omapzoom.org/?p=kernel/omap.git;a=shortlog;h=refs/heads/p-androi… Due to android.git.kernel.org down, AFAIK there's no public access to common-3.1 direct otherwise at the moment. So what's this tree good for? If you have a kernel for any arch or board that is based on Linus HEAD, 3.1-rc8 at the moment, you can merge or rebase a copy of it with linaro-androidization-tracking to create an Android version of the same kernel. That's very handy if you did your work to get stuff looking good on Vanilla Linus HEAD and don't want to repeat the effort to get the same features coming in an Android kernel. Until now there was no way to casually Androidize a Linus HEAD basis tree unless it happened common-3.x was tracking it, which it only does for a short period at the end. It meant that you had to use old release to start integrating and adding drivers for Android and backport from HEAD anything nice that was coming. Now with this tree, you can do your work on Linus HEAD and fork off working release trees when Linus HEAD goes through a release. This Androidization tree is generic and should be usable for any arch or board, there's nothing TI specific in there. Why then is TI Landing team announcing it / TI go to the effort of creating their original one we based off? Nobody else in Linaro wanted to do the work to create and maintain it, so we own it at the moment. We'll have to see how tough it is to keep tracking Linus HEAD through the post-release patchstorm but reviewing the Androidization patchset I'm cautiously optimistic. I don't have any connection to Google guys who are basically doing the same work on common-3.x, but it would be very cool to be able to cooperate with them on bringing this Androidization patchset forward for everyone's benefit. The second branch is "tilt-android-tracking". This is our main tracking branch tilt-tracking for Panda enablement we have been running for some months combined with "linaro-androidization-tracking" above. This gets you an effective Panda enabled "3.1 preview" kernel that we have had for a while on Vanilla also on Android in an ongoing way. Current status of it is + 1080p SGX acceleration - Suspend borked - WLAN borked But we only generated it Sunday, we are working on those issues now. Lastly TILT is also providing tracking versions of the Android autobuilt Panda-LEB tarballs that are ready to use. These are the Autobuilt tarballs with the kernel replaced with a tracking one by us. You can find them linked from our git repo in tilt-android-tracking column of the status table there. -Andy -- Andy Green | TI Landing Team Leader Linaro.org │ Open source software for ARM SoCs | Follow Linaro http://facebook.com/pages/Linaro/155974581091106 - http://twitter.com/#!/linaroorg - http://linaro.org/linaro-blog

13 years, 10 months

[PATCH V2 0/2] ARM: S3C2410: Remove section mismatch warning

by Tushar Behera

While compiling with s3c2410_defconfig, we receive 4 section mismatch warnings. Patch 1 addresses a couple of warnings related to usb_simtec_init(). Patch 2 addresses mismatch warnings in a couple of mach-*/irq.c files. Changes for V2: * The original patch is splitted to address to different logical solutions. * __initdata attribute is removed from struct sysdev_driver structures and __init attribute is removed from all referenced function definitions. The patches are rebased on v3.1-rc8. They are only build tested, they are not boot tested on any hardware. Tushar Behera (2): ARM: S3C2410: Add __init attribute to usb_simtec_init() ARM: S3C2410: irq: Remove __init attributes to fix compilation warning arch/arm/mach-s3c2410/usb-simtec.c | 2 +- arch/arm/mach-s3c2410/usb-simtec.h | 2 +- arch/arm/mach-s3c2416/irq.c | 4 ++-- arch/arm/mach-s3c2443/irq.c | 4 ++-- 4 files changed, 6 insertions(+), 6 deletions(-) -- 1.7.4.1

13 years, 10 months

[GIT PULL][U-boot] Add support for MC34708 based i.MX53 QuickStart

by Eric Miao

The following changes since commit 212bd07b46a8928a05b0dd0062a5c967a784d122: Revert "armv7: adapt omap3 to the new cache maintenance framework" (2011-09-28 23:53:14 -0600) are available in the git repository at: git://git.linaro.org/bsp/freescale/u-boot-linaro.git master Eric Miao (2): mxc_i2c: fix i2c_probe() failure by using i2c_reset() mx53loco: add support for MC34708 board/freescale/mx53loco/mx53loco.c | 57 +++++++++++++++++++++++++++-------- drivers/i2c/mxc_i2c.c | 3 +- include/configs/mx53loco.h | 3 +- 3 files changed, 47 insertions(+), 16 deletions(-)

13 years, 10 months

[PATCH 0/2] Add support for Freescale's MC34708 based i.MX53 QuickStart

by Eric Miao

The two patches below added support for the new i.MX53 QuickStart boards, which are based on Freescale's own MC34708 PMIC (Power Management IC), replacing the previous Dialog Semi's DA9053. The resulting binary will be working on both the DA9053 based boards and the newly MC34708 based boards. [PATCH 1/2] mxc_i2c: fix i2c_probe() failure by using i2c_reset() [PATCH 2/2] mx53loco: add support for MC34708

13 years, 10 months

All recent hwpack builds on snapshots.linaro.org are failing...

by Dave Martin

Hi all, does anyone know why all the hwpack builds have started failing? See, for example: http://snapshots.linaro.org/11.05-daily/linaro-hwpacks/panda/20111006/0/bui… ...a similar problem seems to have affected the recent builds for every hwpack. Looks like some build-depends package is not getting installed properly. Cheers ---Dave

13 years, 10 months

Oneiric image directory on snapshots.linaro.org

by Paul Larson

I know this has come up before, but I'd like to raise it again: Is there any reason for the lack of consistency between directory layouts for: http://snapshots.linaro.org/oneiric/ vs. http://snapshots.linaro.org/11.05-daily/ Would it be possible to rename the oneiric directory to 11.11-daily and split the hwpacks off into a linaro-hwpacks directory like the 11.04 images? Also, keeping some kind of -oneiric or -11.11 on the image/hwpack dirs probably makes sense, but are we planning on changing anything after these become the default LEB images? Thanks, Paul Larson

13 years, 10 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

linaro-dev October 2011