Kernel-build-reports

kernel-build-reports@lists.linaro.org

107303 discussions

arm-soc boot: 26 pass, 6 fail (v3.13-rc5-1062-g25921cf)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: arm-soc Git describe: v3.13-rc5-1062-g25921cf Failed boot tests (console logs at the end) =========================================== am335x-boneblack: FAIL: multi_v7_defconfig omap3-beagle-xm: FAIL: multi_v7_defconfig omap4-panda-es: FAIL: multi_v7_defconfig am335x-bone: FAIL: multi_v7_defconfig omap3-tobi,3730storm: FAIL: multi_v7_defconfig omap3-tobi,3530overo: FAIL: multi_v7_defconfig Full Report =========== omap2plus_defconfig ------------------- am335x-boneblack PASS: 0 min 27.8 sec omap3-beagle-xm PASS: 1 min 0.5 sec am335x-bone PASS: 0 min 26.6 sec omap4-panda PASS: 1 min 7.0 sec omap4-panda-es PASS: 1 min 8.7 sec omap3-tobi,3730storm PASS: 0 min 24.1 sec omap3-tobi,3530overo PASS: 0 min 21.8 sec tegra_defconfig --------------- tegra30-beaver PASS: 0 min 16.9 sec imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual PASS: 0 min 16.9 sec imx6dl-wandboard,wand-solo PASS: 0 min 18.5 sec imx6q-wandboard PASS: 0 min 16.8 sec sunxi_defconfig --------------- sun7i-a20-cubieboard2 PASS: 0 min 12.0 sec mvebu_defconfig --------------- armada-xp-openblocks-ax3-4 PASS: 0 min 22.0 sec armada-370-mirabox PASS: 0 min 20.3 sec exynos_defconfig ---------------- exynos5250-arndale PASS: 0 min 29.7 sec multi_v7_defconfig ------------------ ste-snowball PASS: 1 min 17.1 sec tegra30-beaver PASS: 0 min 19.0 sec am335x-boneblack FAIL: 0 min 30.6 sec omap3-beagle-xm FAIL: 0 min 56.8 sec sun7i-a20-cubieboard2 PASS: 0 min 13.4 sec armada-370-mirabox PASS: 0 min 21.6 sec omap4-panda PASS: 0 min 53.2 sec omap4-panda-es FAIL: 1 min 48.3 sec armada-xp-openblocks-ax3-4 PASS: 0 min 23.8 sec imx6dl-wandboard,wand-solo PASS: 0 min 17.2 sec am335x-bone FAIL: 0 min 29.4 sec imx6q-wandboard PASS: 0 min 16.6 sec omap3-tobi,3730storm FAIL: 0 min 25.4 sec imx6dl-wandboard,wand-dual PASS: 0 min 17.6 sec omap3-tobi,3530overo FAIL: 0 min 27.1 sec u8500_defconfig --------------- ste-snowball PASS: 0 min 27.9 sec sama5_defconfig --------------- sama5d35ek PASS: 0 min 17.5 sec Console logs for failures ========================= multi_v7_defconfig ------------------ am335x-boneblack: FAIL: last 24 lines of boot log: -------------------------------------------------- done Bytes transferred = 17911 (45f7 hex) U-Boot#printenv bootargs printenv bootargs bootargs=console=ttyO0,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.176:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none U-Boot#bootz 0x80200000 0x81000000 0x81f00000 bootz 0x80200000 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 9f19b000, end 9f237300 ... OK Using Device Tree in place at 81f00000, end 81f075f6 Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 30.64 seconds. # PYBOOT: Result: FAIL omap3-beagle-xm: FAIL: last 24 lines of boot log: ------------------------------------------------- done Bytes transferred = 15577 (3cd9 hex) OMAP3 beagleboard.org # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.152:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none OMAP3 beagleboard.org #bootz ${loadaddr} 0x81000000 0x81f00000 bootz ${loadaddr} 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8ff63000, end 8ffff300 ... OK Loading Device Tree to 8ff5c000, end 8ff62cd8 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 56.84 seconds. # PYBOOT: Result: FAIL omap4-panda-es: FAIL: last 24 lines of boot log: ------------------------------------------------ [ 1.529663] Registering SWP/SWPB emulation handler [ 1.535339] reg-fixed-voltage wl12xx_vmmc.10: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_gpio, deferring probe [ 1.548156] platform wl12xx_vmmc.10: Driver reg-fixed-voltage requests probe deferral [ 1.556732] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 1.568298] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 1.575805] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 1.587310] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 1.587341] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 1.606353] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 1.613861] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 1.625366] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 1.633117] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.640777] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.648345] omap_hsmmc 4809c000.mmc: vmmc regulator missing [ 1.652740] omap-dma-engine 4a056000.dma-controller: freeing channel for 61 [ 1.661560] omap-dma-engine 4a056000.dma-controller: freeing channel for 62 [ 1.668853] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.676605] omap_hsmmc 480d5000.mmc: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_pins, deferring probe [ 1.688476] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.696044] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.704956] spear_cpufreq: Invalid cpufreq_tbl~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 108.32 seconds. # PYBOOT: Result: FAIL am335x-bone: FAIL: last 24 lines of boot log: --------------------------------------------- done Bytes transferred = 17315 (43a3 hex) U-Boot# printenv bootargs printenv bootargs bootargs=console=ttyO0,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.174:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none U-Boot# bootz 0x80200000 0x81000000 0x81f00000 bootz 0x80200000 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8f19b000, end 8f237300 ... OK Using Device Tree in place at 81f00000, end 81f073a2 Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 29.41 seconds. # PYBOOT: Result: FAIL omap3-tobi,3730storm: FAIL: last 24 lines of boot log: ------------------------------------------------------ smc911x: MAC 00:15:c9:28:f0:11 Using smc911x-0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.159 Filename 'tmp/3730storm-YoYIWN/omap3-tobi.dtb'. Load address: 0x81f00000 Loading: *## 1.8 MiB/s done Bytes transferred = 15191 (3b57 hex) Overo # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.159:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none Overo # bootz ${loadaddr} - 0x81f00000 bootz ${loadaddr} - 0x81f00000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Device Tree to 8fff9000, end 8ffffb56 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 25.35 seconds. # PYBOOT: Result: FAIL omap3-tobi,3530overo: FAIL: last 24 lines of boot log: ------------------------------------------------------ done Bytes transferred = 15191 (3b57 hex) Overo # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk debug rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.151:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none Overo # bootz ${loadaddr} 0x81000000 0x81f00000 bootz ${loadaddr} 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8ff63000, end 8ffff300 ... OK Loading Device Tree to 8ff5c000, end 8ff62b56 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 27.09 seconds. # PYBOOT: Result: FAIL

11 years, 4 months

arm-soc boot: 27 passed 2 failed (arm-soc/v3.13-rc5-1062-g25921cf)

by Olof's autobooter

Failed boards: bbb multi_v7_defconfig : FAILED 1:25.24 panda multi_v7_defconfig : FAILED 1:45.47 Successful boards: apc vt8500_v6_v7_defconfig : passed 1:20.14 arndale exynos_defconfig : passed 1:06.98 bbb omap2plus_defconfig : passed 1:37.18 beaver tegra_defconfig : passed 0:53.88 beaver multi_v7_defconfig : passed 0:50.61 capri bcm_defconfig : passed 0:42.69 capri multi_v7_defconfig : passed 0:44.19 cubie sunxi_defconfig : passed 0:53.22 cubie multi_v7_defconfig : passed 0:51.82 cubie2 sunxi_defconfig : passed 0:51.93 cubie2 multi_v7_defconfig : passed 0:59.34 cubie2 multi_lpae_defconfig : passed 0:50.22 cubox dove_defconfig : warnings 1:07.29 dalmore tegra_defconfig : passed 1:19.69 dalmore multi_v7_defconfig : passed 1:20.80 dalmore multi_lpae_defconfig : passed 1:18.52 panda omap2plus_defconfig : passed 1:19.69 sama5 sama5_defconfig : passed 1:52.96 seaboard tegra_defconfig : passed 0:59.13 seaboard multi_v7_defconfig : passed 1:09.79 snow exynos_defconfig : passed 1:21.04 snowball u8500_defconfig : passed 1:31.68 snowball multi_v7_defconfig : passed 2:14.29 trimslice tegra_defconfig : passed 0:58.85 trimslice multi_v7_defconfig : passed 1:06.98 wandboard imx_v6_v7_defconfig : passed 0:58.21 wandboard multi_v7_defconfig : passed 1:14.84 Board legend is available at http://arm-soc.lixom.net/boards.html Last entries of failed logs below: ======================================================================== Board bbb-multi_v7_defconfig failure log: ------------------------------------------------- Using cpsw device TFTP from server 172.16.1.3; our IP address is 172.16.1.121 Filename 'arm-soc/v3.13-rc5-1062-g25921cf/multi_v7_defconfig/zImage'. Load address: 0x80200000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ##################################### 1.2 MiB/s done Bytes transferred = 4350736 (426310 hex) U-Boot# setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U-Boot# tftp 0x81f00000 arm-soc/v3.13-rc5-1062-g25921cf/multi_v7_defconfig/dtbs/am335x-boneblack.dtb tftp 0x81f00000 arm-soc/v3.13-rc5-1062-g25921cf/multi_v7_defconfig/dtbs/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 172.16.1.3; our IP address is 172.16.1.121 Filename 'arm-soc/v3.13-rc5-1062-g25921cf/multi_v7_defconfig/dtbs/am335x-boneblack.dtb'. Load address: 0x81f00000 Loading: *## 472.7 KiB/s done Bytes transferred = 17911 (45f7 hex) U-Boot# setenv bootargs console=ttyO0,115200 root=/dev/mmcblk0p2 rootwait rw debug earlyprintk setenv bootargs console=ttyO0,115200 root=/dev/mmcblk0p2 rootwait rw debug earlyprintk U-Boot# printenv bootargs printenv bootargs bootargs=console=ttyO0,115200 root=/dev/mmcblk0p2 rootwait rw debug earlyprintk U-Boot# bootz 0x80200000 - 0x81f00000 bootz 0x80200000 - 0x81f00000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Using Device Tree in place at 81f00000, end 81f075f6 Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board panda-multi_v7_defconfig failure log: ------------------------------------------------- [ 1.422668] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.430114] omap_hsmmc 480d5000.mmc: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_pins, deferring probe [ 1.442016] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.449676] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.456481] usbcore: registered new interface driver usbhid [ 1.462341] usbhid: USB HID core driver [ 1.469268] TCP: cubic registered [ 1.472778] NET: Registered protocol family 17 [ 1.477661] Key type dns_resolver registered [ 1.482543] Power Management for TI OMAP4+ devices. [ 1.487701] Power Management for TI OMAP4. [ 1.492004] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.499145] Registering SWP/SWPB emulation handler [ 1.505157] reg-fixed-voltage wl12xx_vmmc.10: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_gpio, deferring probe [ 1.517852] platform wl12xx_vmmc.10: Driver reg-fixed-voltage requests probe deferral [ 1.526184] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 1.538024] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 1.538024] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 1.557037] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 1.564544] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 1.576049] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 1.576507] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 1.595092] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 1.602813] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.610504] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.618072] omap_hsmmc 4809c000.mmc: vmmc regulator missing [ 1.618438] omap-dma-engine 4a056000.dma-controller: freeing channel for 61 [ 1.631286] omap-dma-engine 4a056000.dma-controller: freeing channel for 62 [ 1.631286] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.646301] omap_hsmmc 480d5000.mmc: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_pins, deferring probe [ 1.658233] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.665802] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.674713] spear_cpufreq: Invalid cpufreq_tbl [ 1.679321] ALSA device list: [ 1.679321] No soundcards found. [ 1.686248] omap_uart 48020000.serial: no wakeirq for uart2 [ 1.692504] Waiting for root device /dev/mmcblk0p2... [ 1.776214] usb 1-1: new high-speed USB device number 2 using ehci-omap ~$off # PYBOOT: Exception: timeout

11 years, 4 months

arm-soc build: 53 warnings 0 failures (arm-soc/v3.13-rc5-1062-g25921cf)

by Olof's autobuilder

Here are the build results from automated periodic testing. The tree being built was arm-soc, found at: http://git.kernel.org/cgit/linux/kernel/git/arm/arm-soc.git (for-next or to-build branch) Topmost commit: 25921cf Merge branch 'next/cleanup' into to-build Build logs (stderr only) can be found at the following link (experimental): http://arm-soc.lixom.net/buildlogs/arm-soc/v3.13-rc5-1062-g25921cf/ Runtime: 41m 0s Passed: 122 Failed: 0 Warnings: 53 Section mismatches: 0 ------------------------------------------------------------------------------- Failed defconfigs: ------------------------------------------------------------------------------- Errors: Warnings: 1 drivers/leds/leds-pwm.c:88:22: warning: unused variable 'node' [-Wunused-variable] 1 drivers/net/ethernet/ti/cpsw.c:2138:2: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' [-Wformat=] 1 drivers/net/ethernet/ti/davinci_cpdma.c:182:3: warning: passing argument 3 of 'dma_alloc_attrs' from incompatible pointer type [enabled by default] 1 drivers/net/ethernet/ti/davinci_cpdma.c:222:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] 1 drivers/net/ethernet/ti/davinci_cpdma.c:223:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] 1 drivers/spi/spi-davinci.c:966:3: warning: format '%d' expects argument of type 'int', but argument 3 has type 'resource_size_t' [-Wformat=] 1 drivers/spi/spi-davinci.c:966:3: warning: format '%d' expects argument of type 'int', but argument 4 has type 'resource_size_t' [-Wformat=] 1 drivers/usb/host/xhci-plat.c:201:12: warning: 'xhci_plat_suspend' defined but not used [-Wunused-function] 1 drivers/usb/host/xhci-plat.c:209:12: warning: 'xhci_plat_resume' defined but not used [-Wunused-function] 2 drivers/mtd/nand/gpmi-nand/gpmi-nand.c:123:13: warning: 'set_geometry_by_ecc_info' defined but not used [-Wunused-function] 2 net/netfilter/ipvs/ip_vs_sync.c:1640:8: warning: unused variable 'ret' [-Wunused-variable] 20 drivers/pinctrl/pinconf.c:299:28: warning: unused variable 'ops' [-Wunused-variable] 20 drivers/pinctrl/pinconf.c:346:28: warning: unused variable 'ops' [-Wunused-variable] Section mismatches:

11 years, 4 months

next boot: 25 pass, 6 fail (next-20140106)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: next Git describe: next-20140106 Failed boot tests (console logs at the end) =========================================== am335x-boneblack: FAIL: multi_v7_defconfig omap3-beagle-xm: FAIL: multi_v7_defconfig omap4-panda-es: FAIL: multi_v7_defconfig am335x-bone: FAIL: multi_v7_defconfig omap3-tobi,3730storm: FAIL: multi_v7_defconfig omap3-tobi,3530overo: FAIL: multi_v7_defconfig Full Report =========== omap2plus_defconfig ------------------- am335x-boneblack PASS: 0 min 28.1 sec omap3-beagle-xm PASS: 0 min 56.8 sec am335x-bone PASS: 0 min 26.8 sec omap4-panda PASS: 1 min 5.8 sec omap4-panda-es PASS: 1 min 2.3 sec omap3-tobi,3730storm PASS: 0 min 22.0 sec omap3-tobi,3530overo PASS: 0 min 23.0 sec tegra_defconfig --------------- tegra30-beaver PASS: 0 min 16.9 sec imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual PASS: 0 min 16.9 sec imx6dl-wandboard,wand-solo PASS: 0 min 16.8 sec imx6q-wandboard PASS: 0 min 16.8 sec sunxi_defconfig --------------- sun7i-a20-cubieboard2 PASS: 0 min 12.2 sec mvebu_defconfig --------------- armada-xp-openblocks-ax3-4 PASS: 0 min 22.2 sec armada-370-mirabox PASS: 0 min 20.2 sec exynos_defconfig ---------------- exynos5250-arndale PASS: 0 min 29.9 sec multi_v7_defconfig ------------------ ste-snowball PASS: 1 min 20.1 sec tegra30-beaver PASS: 0 min 19.6 sec am335x-boneblack FAIL: 0 min 30.7 sec omap3-beagle-xm FAIL: 0 min 53.2 sec sun7i-a20-cubieboard2 PASS: 0 min 13.6 sec armada-370-mirabox PASS: 0 min 21.4 sec omap4-panda PASS: 0 min 53.6 sec omap4-panda-es FAIL: 1 min 46.9 sec armada-xp-openblocks-ax3-4 PASS: 0 min 24.0 sec imx6dl-wandboard,wand-solo PASS: 0 min 17.3 sec am335x-bone FAIL: 0 min 29.5 sec imx6q-wandboard PASS: 0 min 16.8 sec omap3-tobi,3730storm FAIL: 0 min 28.4 sec imx6dl-wandboard,wand-dual PASS: 0 min 17.5 sec omap3-tobi,3530overo FAIL: 0 min 27.0 sec u8500_defconfig --------------- ste-snowball PASS: 0 min 31.5 sec Console logs for failures ========================= multi_v7_defconfig ------------------ am335x-boneblack: FAIL: last 24 lines of boot log: -------------------------------------------------- done Bytes transferred = 17911 (45f7 hex) U-Boot# printenv bootargs printenv bootargs bootargs=console=ttyO0,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.176:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none U-Boot# bootz 0x80200000 0x81000000 0x81f00000 bootz 0x80200000 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 9f19b000, end 9f237300 ... OK Using Device Tree in place at 81f00000, end 81f075f6 Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 30.68 seconds. # PYBOOT: Result: FAIL omap3-beagle-xm: FAIL: last 24 lines of boot log: ------------------------------------------------- done Bytes transferred = 15577 (3cd9 hex) OMAP3 beagleboard.org # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.152:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none OMAP3 beagleboard.org # bootz ${loadaddr} 0x81000000 0x81f00000 bootz ${loadaddr} 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8ff63000, end 8ffff300 ... OK Loading Device Tree to 8ff5c000, end 8ff62cd8 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 53.18 seconds. # PYBOOT: Result: FAIL omap4-panda-es: FAIL: last 24 lines of boot log: ------------------------------------------------ [ 1.589843] platform wl12xx_vmmc.10: Driver reg-fixed-voltage requests probe deferral [ 1.598083] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 1.609924] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 1.617156] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 1.628936] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 1.636169] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 1.647918] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 1.655151] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 1.666900] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 1.674591] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.682250] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.685638] omap_hsmmc 4809c000.mmc: vmmc regulator missing [ 1.695739] omap-dma-engine 4a056000.dma-controller: freeing channel for 61 [ 1.695739] omap-dma-engine 4a056000.dma-controller: freeing channel for 62 [ 1.710357] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.718048] omap_hsmmc 480d5000.mmc: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_pins, deferring probe [ 1.729919] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.737548] leds-gpio leds.6: could not find pctldev for node /ocp/pinmux@4a100040/gpio_led_pmx, deferring probe [ 1.748229] platform leds.6: Driver leds-gpio requests probe deferral [ 1.755401] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.764099] spear_cpufreq: Invalid cpufreq_tbl~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 106.87 seconds. # PYBOOT: Result: FAIL am335x-bone: FAIL: last 24 lines of boot log: --------------------------------------------- done Bytes transferred = 17315 (43a3 hex) U-Boot# printenv bootargs printenv bootargs bootargs=console=ttyO0,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.174:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none U-Boot# bootz 0x80200000 0x81000000 0x81f00000 bootz 0x80200000 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8f19b000, end 8f237300 ... OK Using Device Tree in place at 81f00000, end 81f073a2 Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 29.50 seconds. # PYBOOT: Result: FAIL omap3-tobi,3730storm: FAIL: last 24 lines of boot log: ------------------------------------------------------ smc911x: MAC 00:15:c9:28:f0:11 Using smc911x-0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.159 Filename 'tmp/3730storm-ULTj3O/omap3-tobi.dtb'. Load address: 0x81f00000 Loading: *## 2.1 MiB/s done Bytes transferred = 15191 (3b57 hex) Overo # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.159:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none Overo # bootz ${loadaddr} - 0x81f00000 bootz ${loadaddr} - 0x81f00000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Device Tree to 8fff9000, end 8ffffb56 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 28.36 seconds. # PYBOOT: Result: FAIL omap3-tobi,3530overo: FAIL: last 24 lines of boot log: ------------------------------------------------------ done Bytes transferred = 15191 (3b57 hex) Overo # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk debug rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.151:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none Overo # bootz ${loadaddr} 0x81000000 0x81f00000 bootz ${loadaddr} 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8ff63000, end 8ffff300 ... OK Loading Device Tree to 8ff5c000, end 8ff62b56 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 27.00 seconds. # PYBOOT: Result: FAIL

11 years, 4 months

next boot: 27 passed 3 failed (next/next-20140106)

by Olof's autobooter

Failed boards: bbb multi_v7_defconfig : FAILED 1:19.04 hummingboard multi_v7_defconfig : FAILED 0:23.21 panda multi_v7_defconfig : FAILED 1:44.33 sama5 sama5_defconfig : BUILD FAILED Successful boards: apc vt8500_v6_v7_defconfig : passed 1:18.19 arndale exynos_defconfig : passed 1:10.14 bbb omap2plus_defconfig : passed 1:37.12 beaver tegra_defconfig : passed 0:54.07 beaver multi_v7_defconfig : passed 0:51.74 capri bcm_defconfig : passed 0:43.01 capri multi_v7_defconfig : passed 0:43.30 cubie sunxi_defconfig : passed 0:50.46 cubie multi_v7_defconfig : passed 0:49.61 cubie2 sunxi_defconfig : passed 0:49.90 cubie2 multi_v7_defconfig : passed 0:57.11 cubie2 multi_lpae_defconfig : passed 0:49.65 cubox dove_defconfig : passed 1:04.24 dalmore tegra_defconfig : passed 1:18.86 dalmore multi_v7_defconfig : passed 1:14.59 dalmore multi_lpae_defconfig : passed 1:17.78 hummingboard imx_v6_v7_defconfig : passed 2:30.09 panda omap2plus_defconfig : passed 1:20.14 seaboard tegra_defconfig : passed 1:00.54 seaboard multi_v7_defconfig : passed 1:11.97 snow exynos_defconfig : passed 1:20.27 snowball u8500_defconfig : passed 1:31.00 snowball multi_v7_defconfig : passed 2:22.56 trimslice tegra_defconfig : passed 1:00.25 trimslice multi_v7_defconfig : passed 1:01.32 wandboard imx_v6_v7_defconfig : passed 0:57.35 wandboard multi_v7_defconfig : passed 1:04.99 Board legend is available at http://arm-soc.lixom.net/boards.html Last entries of failed logs below: ======================================================================== Board bbb-multi_v7_defconfig failure log: ------------------------------------------------- TFTP from server 172.16.1.3; our IP address is 172.16.1.121 Filename 'next/next-20140106/multi_v7_defconfig/zImage'. Load address: 0x80200000 Loading: *################################################################# ########node: bbb status: on ######################################################### ################################################################# ################################################################# ######################################## 1.2 MiB/s done Bytes transferred = 4401448 (432928 hex) U-Boot# setenv serverip 172.16.1.3 setenv serverip 172.16.1.3 U-Boot# tftp 0x81f00000 next/next-20140106/multi_v7_defconfig/dtbs/am335x-boneblack.dtb tftp 0x81f00000 next/next-20140106/multi_v7_defconfig/dtbs/am335x-boneblack.dtb link up on port 0, speed 100, full duplex Using cpsw device TFTP from server 172.16.1.3; our IP address is 172.16.1.121 Filename 'next/next-20140106/multi_v7_defconfig/dtbs/am335x-boneblack.dtb'. Load address: 0x81f00000 Loading: *## 583 KiB/s done Bytes transferred = 17911 (45f7 hex) U-Boot# setenv bootargs console=ttyO0,115200 root=/dev/mmcblk0p2 rootwait rw debug earlyprintk setenv bootargs console=ttyO0,115200 root=/dev/mmcblk0p2 rootwait rw debug earlyprintk U-Boot# printenv bootargs printenv bootargs bootargs=console=ttyO0,115200 root=/dev/mmcblk0p2 rootwait rw debug earlyprintk U-Boot# bootz 0x80200000 - 0x81f00000 bootz 0x80200000 - 0x81f00000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Using Device Tree in place at 81f00000, end 81f075f6 Starting kernel ... ~$off # PYBOOT: Exception: timeout ======================================================================== Board hummingboard-multi_v7_defconfig failure log: ------------------------------------------------- [ 1.074724] hub 1-0:1.0: 1 port detected [ 1.079380] ci_hdrc ci_hdrc.1: doesn't support gadget [ 1.084450] ci_hdrc ci_hdrc.1: EHCI Host Controller [ 1.089395] ci_hdrc ci_hdrc.1: new USB bus registered, assigned bus number 2 [ 1.114711] ci_hdrc ci_hdrc.1: USB 2.0 started, EHCI 1.00 [ 1.120850] hub 2-0:1.0: USB hub found [ 1.124644] hub 2-0:1.0: 1 port detected [ 1.129323] mousedev: PS/2 mouse device common for all mice [ 1.136582] i2c /dev entries driver [ 1.141283] sdhci: Secure Digital Host Controller Interface driver [ 1.147512] sdhci: Copyright(c) Pierre Ossman [ 1.152356] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.158592] sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state, work on normal mode [ 1.167776] mmc0: no vqmmc regulator found [ 1.214716] mmc0: SDHCI controller on 2194000.usdhc [2194000.usdhc] using ADMA [ 1.222728] usbcore: registered new interface driver usbhid [ 1.228344] usbhid: USB HID core driver [ 1.235747] TCP: cubic registered [ 1.239079] NET: Registered protocol family 17 [ 1.243695] Key type dns_resolver registered [ 1.248133] Registering SWP/SWPB emulation handler [ 1.256025] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.264303] spear_cpufreq: Invalid cpufreq_tbl [ 1.275127] ALSA device list: [ 1.278303] No soundcards found. [ 1.282408] VFS: Cannot open root device "mmcblk0p2" or unknown-block(0,0): error -6 [ 1.290190] Please append a correct "root=" boot option; here are the available partitions: [ 1.298569] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ 1.306843] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc7-next-20140106 #1 [ 1.314363] [<c001580c>] (unwind_backtrace) from [<c00113dc>] (show_stack+0x10/0x14) [ 1.322121] [<c00113dc>] (show_stack) from [<c057fd84>] (dump_stack+0x84/0x94) [ 1.329361] [<c057fd84>] (dump_stack) from [<c057cd60>] (panic+0xa0/0x1f4) [ 1.336255] [<c057cd60>] (panic) from [<c07fc034>] (mount_block_root+0x1a0/0x230) [ 1.343748] [<c07fc034>] (mount_block_root) from [<c07fc1cc>] (mount_root+0x108/0x110) [ 1.351675] [<c07fc1cc>] (mount_root) from [<c07fc32c>] (prepare_namespace+0x158/0x1a0) [ 1.359690] [<c07fc32c>] (prepare_namespace) from [<c07fbcf0>] (kernel_init_freeable+0x1cc/0x1dc) [ 1.368574] [<c07fbcf0>] (kernel_init_freeable) from [<c057a1f4>] (kernel_init+0x8/0x120) [ 1.376765] [<c057a1f4>] (kernel_init) from [<c000e578>] (ret_from_fork+0x14/0x3c) ~$off # PYBOOT: Exception: panic ======================================================================== Board panda-multi_v7_defconfig failure log: ------------------------------------------------- [ 1.473175] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.479644] leds-gpio leds.6: could not find pctldev for node /ocp/pinmux@4a100040/gpio_led_pmx, deferring probe [ 1.490356] platform leds.6: Driver leds-gpio requests probe deferral [ 1.497467] usbcore: registered new interface driver usbhid [ 1.503326] usbhid: USB HID core driver [ 1.510650] TCP: cubic registered [ 1.514129] NET: Registered protocol family 17 [ 1.518981] Key type dns_resolver registered [ 1.523895] Power Management for TI OMAP4+ devices. [ 1.529022] Power Management for TI OMAP4. [ 1.533355] OMAP4 PM: u-boot >= v2012.07 is required for full PM support [ 1.540740] Registering SWP/SWPB emulation handler [ 1.546569] reg-fixed-voltage wl12xx_vmmc.10: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_gpio, deferring probe [ 1.559265] platform wl12xx_vmmc.10: Driver reg-fixed-voltage requests probe deferral [ 1.567504] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 1.579345] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 1.586853] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 1.598358] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 1.605590] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 1.617340] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 1.624572] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 1.636322] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 1.644012] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.651672] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.655303] omap_hsmmc 4809c000.mmc: vmmc regulator missing [ 1.665161] omap-dma-engine 4a056000.dma-controller: freeing channel for 61 [ 1.665161] omap-dma-engine 4a056000.dma-controller: freeing channel for 62 [ 1.679779] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.687469] omap_hsmmc 480d5000.mmc: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_pins, deferring probe [ 1.699340] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.706970] leds-gpio leds.6: could not find pctldev for node /ocp/pinmux@4a100040/gpio_led_pmx, deferring probe [ 1.717651] platform leds.6: Driver leds-gpio requests probe deferral [ 1.724609] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.733489] spear_cpufreq: Invalid cpufreq_tbl [ 1.743621] ALSA device list: [ 1.747009] No soundcards found. [ 1.750701] omap_uart 48020000.serial: no wakeirq for uart2 [ 1.756988] Waiting for root device /dev/mmcblk0p2... ~$off # PYBOOT: Exception: timeout

11 years, 4 months

next build: 32 warnings 9 failures (next/next-20140106)

by Olof's autobuilder

Here are the build results from automated periodic testing. The tree being built was next, found at: http://git.kernel.org/cgit/linux/kernel/git/next/linux-next.git (master branch) Topmost commit: b4a839b Add linux-next specific files for 20140106 Build logs (stderr only) can be found at the following link (experimental): http://arm-soc.lixom.net/buildlogs/next/next-20140106/ Runtime: 38m 11s Passed: 113 Failed: 9 Warnings: 32 Section mismatches: 0 ------------------------------------------------------------------------------- Failed defconfigs: at91_dt_defconfig at91rm9200_defconfig at91sam9260_9g20_defconfig at91sam9261_9g10_defconfig at91sam9263_defconfig at91sam9g45_defconfig mini2440_defconfig s3c2410_defconfig sama5_defconfig ------------------------------------------------------------------------------- Errors: at91_dt_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined drivers/usb/host/ohci-at91.c:206:2: error: type defaults to 'int' in declaration of 'at91_stop_hc' [-Werror=implicit-int] drivers/usb/host/ohci-at91.c:206:2: error: conflicting types for 'at91_stop_hc' drivers/usb/host/ohci-at91.c:208:5: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token drivers/usb/host/ohci-at91.c:210:2: error: expected identifier or '(' before 'return' drivers/usb/host/ohci-at91.c:211:1: error: expected identifier or '(' before '}' token at91rm9200_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined drivers/usb/host/ohci-at91.c:206:2: error: type defaults to 'int' in declaration of 'at91_stop_hc' [-Werror=implicit-int] drivers/usb/host/ohci-at91.c:206:2: error: conflicting types for 'at91_stop_hc' drivers/usb/host/ohci-at91.c:208:5: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token drivers/usb/host/ohci-at91.c:210:2: error: expected identifier or '(' before 'return' drivers/usb/host/ohci-at91.c:211:1: error: expected identifier or '(' before '}' token at91sam9260_9g20_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined drivers/usb/host/ohci-at91.c:206:2: error: type defaults to 'int' in declaration of 'at91_stop_hc' [-Werror=implicit-int] drivers/usb/host/ohci-at91.c:206:2: error: conflicting types for 'at91_stop_hc' drivers/usb/host/ohci-at91.c:208:5: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token drivers/usb/host/ohci-at91.c:210:2: error: expected identifier or '(' before 'return' drivers/usb/host/ohci-at91.c:211:1: error: expected identifier or '(' before '}' token at91sam9261_9g10_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined drivers/usb/host/ohci-at91.c:206:2: error: type defaults to 'int' in declaration of 'at91_stop_hc' [-Werror=implicit-int] drivers/usb/host/ohci-at91.c:206:2: error: conflicting types for 'at91_stop_hc' drivers/usb/host/ohci-at91.c:208:5: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token drivers/usb/host/ohci-at91.c:210:2: error: expected identifier or '(' before 'return' drivers/usb/host/ohci-at91.c:211:1: error: expected identifier or '(' before '}' token at91sam9263_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined drivers/usb/host/ohci-at91.c:206:2: error: type defaults to 'int' in declaration of 'at91_stop_hc' [-Werror=implicit-int] drivers/usb/host/ohci-at91.c:206:2: error: conflicting types for 'at91_stop_hc' drivers/usb/host/ohci-at91.c:208:5: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token drivers/usb/host/ohci-at91.c:210:2: error: expected identifier or '(' before 'return' drivers/usb/host/ohci-at91.c:211:1: error: expected identifier or '(' before '}' token at91sam9g45_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined drivers/usb/host/ohci-at91.c:206:2: error: type defaults to 'int' in declaration of 'at91_stop_hc' [-Werror=implicit-int] drivers/usb/host/ohci-at91.c:206:2: error: conflicting types for 'at91_stop_hc' drivers/usb/host/ohci-at91.c:208:5: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token drivers/usb/host/ohci-at91.c:210:2: error: expected identifier or '(' before 'return' drivers/usb/host/ohci-at91.c:211:1: error: expected identifier or '(' before '}' token mini2440_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/leds/leds-s3c24xx.c:100:2: error: implicit declaration of function 's3c_gpio_setpull' [-Werror=implicit-function-declaration] drivers/leds/leds-s3c24xx.c:100:32: error: 'S3C_GPIO_PULL_NONE' undeclared (first use in this function) s3c2410_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! arch/arm/mach-s3c24xx/mach-osiris-dvs.c:76:4: error: implicit declaration of function 'S3C2410_GPB' [-Werror=implicit-function-declaration] drivers/leds/leds-s3c24xx.c:100:2: error: implicit declaration of function 's3c_gpio_setpull' [-Werror=implicit-function-declaration] drivers/leds/leds-s3c24xx.c:100:32: error: 'S3C_GPIO_PULL_NONE' undeclared (first use in this function) sama5_defconfig: arch/arm/Kconfig:1963:error: recursive dependency detected! drivers/usb/host/ohci-at91.c:190:4: error: label 'err' used but not defined drivers/usb/host/ohci-at91.c:206:2: error: type defaults to 'int' in declaration of 'at91_stop_hc' [-Werror=implicit-int] drivers/usb/host/ohci-at91.c:206:2: error: conflicting types for 'at91_stop_hc' drivers/usb/host/ohci-at91.c:208:5: error: expected '=', ',', ';', 'asm' or '__attribute__' before ':' token drivers/usb/host/ohci-at91.c:210:2: error: expected identifier or '(' before 'return' drivers/usb/host/ohci-at91.c:211:1: error: expected identifier or '(' before '}' token Warnings: 1 drivers/usb/host/xhci-plat.c:203:12: warning: 'xhci_plat_suspend' defined but not used [-Wunused-function] 1 drivers/usb/host/xhci-plat.c:211:12: warning: 'xhci_plat_resume' defined but not used [-Wunused-function] 2 buildall.arm.multi_lpae_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) 2 buildall.arm.multi_v7_defconfig.log.passed:warning: (ARM_HIGHBANK_CPUFREQ) selects GENERIC_CPUFREQ_CPU0 which has unmet direct dependencies (ARCH_HAS_CPUFREQ && CPU_FREQ && HAVE_CLK && REGULATOR && OF && THERMAL && CPU_THERMAL) 2 net/netfilter/ipvs/ip_vs_sync.c:1640:8: warning: unused variable 'ret' [-Wunused-variable] 3 fs/nfsd/nfssvc.c:246:53: warning: array subscript is above array bounds [-Warray-bounds] 7 drivers/usb/host/ohci-at91.c:206:2: warning: data definition has no type or storage class [enabled by default] 7 drivers/usb/host/ohci-at91.c:206:2: warning: parameter names (without types) in function declaration [enabled by default] 7 drivers/usb/host/ohci-at91.c:97:13: warning: 'at91_stop_hc' defined but not used [-Wunused-function] Section mismatches:

11 years, 4 months

mainline boot: 32 pass, 0 fail (v3.13-rc7-12-gf0a679a)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: mainline Git describe: v3.13-rc7-12-gf0a679a Full Report =========== omap2plus_defconfig ------------------- am335x-boneblack PASS: 0 min 27.9 sec omap3-beagle-xm PASS: 1 min 0.6 sec am335x-bone PASS: 0 min 26.6 sec omap4-panda PASS: 1 min 4.7 sec omap4-panda-es PASS: 1 min 4.1 sec omap3-tobi,3730storm PASS: 0 min 23.7 sec omap3-tobi,3530overo PASS: 0 min 22.0 sec tegra_defconfig --------------- tegra30-beaver PASS: 0 min 17.0 sec imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual PASS: 0 min 18.2 sec imx6dl-wandboard,wand-solo PASS: 0 min 18.3 sec imx6q-wandboard PASS: 0 min 16.9 sec sunxi_defconfig --------------- sun7i-a20-cubieboard2 PASS: 0 min 12.0 sec mvebu_defconfig --------------- armada-xp-openblocks-ax3-4 PASS: 0 min 22.1 sec armada-370-mirabox PASS: 0 min 20.1 sec exynos_defconfig ---------------- exynos5250-arndale PASS: 0 min 29.8 sec multi_v7_defconfig ------------------ ste-snowball PASS: 0 min 32.2 sec tegra30-beaver PASS: 0 min 20.2 sec am335x-boneblack PASS: 0 min 24.7 sec omap3-beagle-xm PASS: 0 min 59.7 sec sun7i-a20-cubieboard2 PASS: 0 min 13.1 sec armada-370-mirabox PASS: 0 min 20.6 sec omap4-panda PASS: 1 min 1.1 sec omap4-panda-es PASS: 1 min 2.7 sec armada-xp-openblocks-ax3-4 PASS: 0 min 22.7 sec imx6dl-wandboard,wand-solo PASS: 0 min 16.5 sec am335x-bone PASS: 0 min 23.5 sec imx6q-wandboard PASS: 0 min 15.8 sec omap3-tobi,3730storm PASS: 0 min 19.7 sec imx6dl-wandboard,wand-dual PASS: 0 min 16.8 sec omap3-tobi,3530overo PASS: 0 min 20.0 sec u8500_defconfig --------------- ste-snowball PASS: 0 min 30.7 sec sama5_defconfig --------------- sama5d35ek PASS: 0 min 17.3 sec

11 years, 4 months

mainline boot: 29 passed 0 failed (mainline/v3.13-rc7-12-gf0a679a)

by Olof's autobooter

Failed boards: Successful boards: apc vt8500_v6_v7_defconfig : passed 1:19.38 arndale exynos_defconfig : passed 1:08.38 bbb omap2plus_defconfig : passed 1:35.84 bbb multi_v7_defconfig : passed 1:22.89 beaver tegra_defconfig : passed 0:52.49 beaver multi_v7_defconfig : passed 0:46.86 capri bcm_defconfig : passed 0:43.52 capri multi_v7_defconfig : passed 0:42.65 cubie sunxi_defconfig : passed 0:52.93 cubie multi_v7_defconfig : passed 0:51.79 cubie2 sunxi_defconfig : passed 0:50.35 cubie2 multi_v7_defconfig : passed 1:00.81 cubie2 multi_lpae_defconfig : passed 0:50.37 cubox dove_defconfig : passed 1:10.92 dalmore tegra_defconfig : passed 1:23.13 dalmore multi_v7_defconfig : passed 1:03.56 dalmore multi_lpae_defconfig : passed 1:01.29 panda omap2plus_defconfig : passed 1:21.06 panda multi_v7_defconfig : passed 1:21.08 sama5 sama5_defconfig : passed 1:49.63 seaboard tegra_defconfig : passed 1:01.74 seaboard multi_v7_defconfig : passed 0:56.59 snow exynos_defconfig : passed 1:25.47 snowball u8500_defconfig : passed 1:27.81 snowball multi_v7_defconfig : passed 1:06.01 trimslice tegra_defconfig : passed 1:00.12 trimslice multi_v7_defconfig : passed 0:52.87 wandboard imx_v6_v7_defconfig : passed 0:56.10 wandboard multi_v7_defconfig : passed 0:59.43 Board legend is available at http://arm-soc.lixom.net/boards.html

11 years, 4 months

mainline build: 11 warnings 0 failures (mainline/v3.13-rc7-12-gf0a679a)

by Olof's autobuilder

Here are the build results from automated periodic testing. The tree being built was mainline, found at: http://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git (master branch) Topmost commit: f0a679a Merge branch 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm Build logs (stderr only) can be found at the following link (experimental): http://arm-soc.lixom.net/buildlogs/mainline/v3.13-rc7-12-gf0a679a/ Runtime: 39m 25s Passed: 119 Failed: 0 Warnings: 11 Section mismatches: 0 ------------------------------------------------------------------------------- Failed defconfigs: ------------------------------------------------------------------------------- Errors: Warnings: 1 drivers/leds/leds-pwm.c:88:22: warning: unused variable 'node' [-Wunused-variable] 1 drivers/net/ethernet/ti/cpsw.c:2140:2: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'resource_size_t' [-Wformat=] 1 drivers/net/ethernet/ti/davinci_cpdma.c:182:3: warning: passing argument 3 of 'dma_alloc_attrs' from incompatible pointer type [enabled by default] 1 drivers/net/ethernet/ti/davinci_cpdma.c:222:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] 1 drivers/net/ethernet/ti/davinci_cpdma.c:223:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast] 1 drivers/spi/spi-davinci.c:966:3: warning: format '%d' expects argument of type 'int', but argument 3 has type 'resource_size_t' [-Wformat=] 1 drivers/spi/spi-davinci.c:966:3: warning: format '%d' expects argument of type 'int', but argument 4 has type 'resource_size_t' [-Wformat=] 2 drivers/mtd/nand/gpmi-nand/gpmi-nand.c:123:13: warning: 'set_geometry_by_ecc_info' defined but not used [-Wunused-function] 2 net/netfilter/ipvs/ip_vs_sync.c:1640:8: warning: unused variable 'ret' [-Wunused-variable] Section mismatches:

11 years, 4 months

arm-soc boot: 25 pass, 7 fail (v3.13-rc5-1047-g5e59dd4)

by Kevin's boot bot

Automated DT boot report for various ARM defconfigs. Tree/Branch: arm-soc Git describe: v3.13-rc5-1047-g5e59dd4 Failed boot tests (console logs at the end) =========================================== am335x-boneblack: FAIL: multi_v7_defconfig omap3-beagle-xm: FAIL: multi_v7_defconfig omap4-panda: FAIL: multi_v7_defconfig omap4-panda-es: FAIL: multi_v7_defconfig am335x-bone: FAIL: multi_v7_defconfig omap3-tobi,3730storm: FAIL: multi_v7_defconfig omap3-tobi,3530overo: FAIL: multi_v7_defconfig Full Report =========== omap2plus_defconfig ------------------- am335x-boneblack PASS: 0 min 27.8 sec omap3-beagle-xm PASS: 1 min 1.7 sec am335x-bone PASS: 0 min 26.6 sec omap4-panda PASS: 1 min 8.6 sec omap4-panda-es PASS: 1 min 11.7 sec omap3-tobi,3730storm PASS: 0 min 24.0 sec omap3-tobi,3530overo PASS: 0 min 21.9 sec tegra_defconfig --------------- tegra30-beaver PASS: 0 min 17.0 sec imx_v6_v7_defconfig ------------------- imx6dl-wandboard,wand-dual PASS: 0 min 17.0 sec imx6dl-wandboard,wand-solo PASS: 0 min 18.4 sec imx6q-wandboard PASS: 0 min 16.7 sec sunxi_defconfig --------------- sun7i-a20-cubieboard2 PASS: 0 min 12.0 sec mvebu_defconfig --------------- armada-xp-openblocks-ax3-4 PASS: 0 min 22.0 sec armada-370-mirabox PASS: 0 min 20.2 sec exynos_defconfig ---------------- exynos5250-arndale PASS: 0 min 59.8 sec multi_v7_defconfig ------------------ ste-snowball PASS: 1 min 20.0 sec tegra30-beaver PASS: 0 min 19.6 sec am335x-boneblack FAIL: 0 min 30.6 sec omap3-beagle-xm FAIL: 0 min 48.6 sec sun7i-a20-cubieboard2 PASS: 0 min 13.4 sec armada-370-mirabox PASS: 0 min 21.5 sec omap4-panda FAIL: 1 min 47.7 sec omap4-panda-es FAIL: 1 min 45.5 sec armada-xp-openblocks-ax3-4 PASS: 0 min 24.0 sec imx6dl-wandboard,wand-solo PASS: 0 min 17.2 sec am335x-bone FAIL: 0 min 29.5 sec imx6q-wandboard PASS: 0 min 16.7 sec omap3-tobi,3730storm FAIL: 0 min 28.2 sec imx6dl-wandboard,wand-dual PASS: 0 min 17.5 sec omap3-tobi,3530overo FAIL: 0 min 30.2 sec u8500_defconfig --------------- ste-snowball PASS: 0 min 27.6 sec sama5_defconfig --------------- sama5d35ek PASS: 0 min 17.4 sec Console logs for failures ========================= multi_v7_defconfig ------------------ am335x-boneblack: FAIL: last 24 lines of boot log: -------------------------------------------------- done Bytes transferred = 17911 (45f7 hex) U-Boot#printenv bootargs printenv bootargs bootargs=console=ttyO0,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.176:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none U-Boot# bootz 0x80200000 0x81000000 0x81f00000 bootz 0x80200000 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 9f19b000, end 9f237300 ... OK Using Device Tree in place at 81f00000, end 81f075f6 Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 30.63 seconds. # PYBOOT: Result: FAIL omap3-beagle-xm: FAIL: last 24 lines of boot log: ------------------------------------------------- done Bytes transferred = 15577 (3cd9 hex) OMAP3 beagleboard.org # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.152:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none OMAP3 beagleboard.org # bootz ${loadaddr} 0x81000000 0x81f00000 bootz ${loadaddr} 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8ff63000, end 8ffff300 ... OK Loading Device Tree to 8ff5c000, end 8ff62cd8 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 48.57 seconds. # PYBOOT: Result: FAIL omap4-panda: FAIL: last 24 lines of boot log: --------------------------------------------- [ 2.017456] reg-fixed-voltage wl12xx_vmmc.9: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_gpio, deferring probe [ 2.030120] platform wl12xx_vmmc.9: Driver reg-fixed-voltage requests probe deferral [ 2.038299] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 2.050354] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 2.057952] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 2.069488] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 2.077117] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 2.077117] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 2.095886] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 2.107788] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 2.115020] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 2.123382] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 2.131042] omap_hsmmc 4809c000.mmc: vmmc regulator missing [ 2.136932] omap-dma-engine 4a056000.dma-controller: freeing channel for 61 [ 2.144256] omap-dma-engine 4a056000.dma-controller: freeing channel for 62 [ 2.151580] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 2.159088] omap_hsmmc 480d5000.mmc: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_pins, deferring probe [ 2.171386] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 2.293243] usb 1-1.1: new high-speed USB device number 3 using ehci-omap [ 2.427032] smsc95xx v1.0.4 ~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 107.69 seconds. # PYBOOT: Result: FAIL omap4-panda-es: FAIL: last 24 lines of boot log: ------------------------------------------------ [ 1.529693] Registering SWP/SWPB emulation handler [ 1.535583] reg-fixed-voltage wl12xx_vmmc.10: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_gpio, deferring probe [ 1.548370] platform wl12xx_vmmc.10: Driver reg-fixed-voltage requests probe deferral [ 1.556762] omap_i2c 48070000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c1_pins, deferring probe [ 1.568542] platform 48070000.i2c: Driver omap_i2c requests probe deferral [ 1.576049] omap_i2c 48072000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c2_pins, deferring probe [ 1.587585] platform 48072000.i2c: Driver omap_i2c requests probe deferral [ 1.595092] omap_i2c 48060000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c3_pins, deferring probe [ 1.606597] platform 48060000.i2c: Driver omap_i2c requests probe deferral [ 1.613830] omap_i2c 48350000.i2c: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_i2c4_pins, deferring probe [ 1.625640] platform 48350000.i2c: Driver omap_i2c requests probe deferral [ 1.633483] omap-dma-engine 4a056000.dma-controller: allocating channel for 62 [ 1.641082] omap-dma-engine 4a056000.dma-controller: allocating channel for 61 [ 1.648712] omap_hsmmc 4809c000.mmc: vmmc regulator missing [ 1.648803] omap-dma-engine 4a056000.dma-controller: freeing channel for 61 [ 1.661895] omap-dma-engine 4a056000.dma-controller: freeing channel for 62 [ 1.669250] platform 4809c000.mmc: Driver omap_hsmmc requests probe deferral [ 1.676788] omap_hsmmc 480d5000.mmc: could not find pctldev for node /ocp/pinmux@4a100040/pinmux_wl12xx_pins, deferring probe [ 1.688873] platform 480d5000.mmc: Driver omap_hsmmc requests probe deferral [ 1.696655] /home/build/work/batch/drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 1.705322] spear_cpufreq: Invalid cpufreq_tbl~$off # PYBOOT: Exception: kernel: ERROR: failed to boot: <class 'pexpect.TIMEOUT'> # PYBOOT: Time: 105.55 seconds. # PYBOOT: Result: FAIL am335x-bone: FAIL: last 24 lines of boot log: --------------------------------------------- done Bytes transferred = 17315 (43a3 hex) U-Boot# printenv bootargs printenv bootargs bootargs=console=ttyO0,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.174:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none U-Boot# bootz 0x80200000 0x81000000 0x81f00000 bootz 0x80200000 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8f19b000, end 8f237300 ... OK Using Device Tree in place at 81f00000, end 81f073a2 Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 29.47 seconds. # PYBOOT: Result: FAIL omap3-tobi,3730storm: FAIL: last 24 lines of boot log: ------------------------------------------------------ smc911x: MAC 00:15:c9:28:f0:11 Using smc911x-0 device TFTP from server 192.168.1.2; our IP address is 192.168.1.159 Filename 'tmp/3730storm-8PTV3F/omap3-tobi.dtb'. Load address: 0x81f00000 Loading: *## 2.1 MiB/s done Bytes transferred = 15191 (3b57 hex) Overo # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.159:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none Overo # bootz ${loadaddr} - 0x81f00000 bootz ${loadaddr} - 0x81f00000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Device Tree to 8fff9000, end 8ffffb56 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 28.19 seconds. # PYBOOT: Result: FAIL omap3-tobi,3530overo: FAIL: last 24 lines of boot log: ------------------------------------------------------ done Bytes transferred = 15191 (3b57 hex) Overo # printenv bootargs printenv bootargs bootargs=console=ttyO2,115200n8 earlyprintk debug rw root=/dev/mmcblk0p2 rootwait rootfstype=ext4 ip=192.168.1.151:192.168.1.2:192.168.1.254:255.255.255.0::::192.168.1.254:none Overo # bootz ${loadaddr} 0x81000000 0x81f00000 bootz ${loadaddr} 0x81000000 0x81f00000 ## Loading init Ramdisk from Legacy Image at 81000000 ... Image Name: Image Type: ARM Linux RAMDisk Image (uncompressed) Data Size: 639744 Bytes = 624.8 KiB Load Address: 81000000 Entry Point: 81000000 ## Flattened Device Tree blob at 81f00000 Booting using the fdt blob at 0x81f00000 Loading Ramdisk to 8ff63000, end 8ffff300 ... OK Loading Device Tree to 8ff5c000, end 8ff62b56 ... OK Starting kernel ... ~$off # PYBOOT: Exception: kernel: ERROR: did not start booting. # PYBOOT: Time: 30.20 seconds. # PYBOOT: Result: FAIL

11 years, 4 months

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

Kernel-build-reports